A freestanding pedestal basin is one of the few bathroom items that a guest or homeowner sees the moment they walk in, yet it is usually specified late in a project and reviewed quickly. When a project buyer evaluates a supplier for the Freestanding Pedestal Basin 1003S, Modern Round Ceramic Stand Basin for Bathroom, the decision is rarely about the basin alone. It is about whether the supplier can confirm dimensions, keep a matching suite together, and deliver the whole order on one schedule. The checklist below follows the way an experienced buyer actually reads a product page and a quotation.
Start With What Has to Be Confirmed Before an Order Is Placed
Ceramic sanitaryware looks simple on a drawing. It is the installation detail that causes rework. Before comparing prices, ask the supplier to confirm each of the following in writing for the exact model you are ordering — not for the range in general.
- Finished dimensions and footprint. The 1003S is listed at 490 × 490 × 805 mm. Check that this footprint fits the setting-out drawing, including clearance for the faucet and for a user standing in front of it.
- How the basin is secured. The 1003S is fixed to the wall through a back panel. That wall has to be able to take the fixing — blockwork or a properly braced stud wall, decided before tiling, not after.
- Drain and rough-in arrangement. Confirm the trap type and the position of the waste outlet against your plumbing drawing. A round stand basin ordered against a square-basin rough-in is an expensive mistake.
- Faucet provision. The 1003S has a pre-reserved tap hole for a single faucet. Confirm tap reach and height so the spout clears the rim, and confirm whether the mixer is included in your line item or supplied separately.
- Which items form the matching set. Bathroom fit-outs are usually specified as a suite across many rooms. Confirm which wall-hung basins and toilets in the same series can be ordered together so the glaze colour and profile match room to room.
Material and Finish Are What You Will Be Judging on After Two Years of Use
The 1003S is made from vitreous ceramic with a high-gloss glaze. In project terms this matters in three specific ways, and each one is worth putting into the specification so that substitutions cannot be quietly made later.
Cleaning regime. A dense glazed surface resists water staining, limescale and discolouration, which is why these basins hold up in hotel and serviced-apartment washrooms where housekeeping cleans daily. Specify the cleaning agents you intend to use and ask the supplier to confirm compatibility — abrasive or strongly acidic products will dull any glaze.
Colour consistency between rooms. Glaze tone varies between production runs. For a project ordering the same basin across several bathrooms, place one order for the whole building rather than repeating small orders over months, and state the required shade on the purchase order.
Edge and rim condition on arrival. Ceramic is heavy and brittle. Ask how basins are packed and braced in the container, and inspect every piece against the packing list before signing. Damage claims after the containers have left the port are difficult to resolve.
Where a Round Stand Basin Fits in a Project
A freestanding pedestal basin solves a particular set of design problems, and it is worth being honest about where it does not fit.
- Villa master bathrooms and ensuite projects. The tapered round silhouette reads as a designed object rather than a utility item, which is why it is specified in villa work such as the Melbourne and Sydney residential projects shown in our project cases.
- Boutique hotel and guesthouse washrooms. A stand basin gives a strong visual at relatively low cost per point, and it does not require a vanity carcass to be manufactured, shipped and installed.
- Where counter space is not needed. Because the design removes the need for a bathroom cabinet, guests lose the storage and counter area a vanity would give. In family bathrooms or high-traffic shared washrooms, pair the stand basin with a Wall Hung Ceramic Basin 1004B at the mirror wall so storage is not lost.
- Accessible and commercial washrooms. Check clearances, tapware type and any project-specific accessibility requirements before specifying a freestanding unit. Confirm these against your own local requirements with your specifier — do not assume a product page covers them.
Buying From a Manufacturer: What Actually Changes on the Order
SANTERSON has been producing furniture and building materials in China since 2008, and bathroom ceramics sit inside the same Bathroom Sanitary Fixtures range as the toilets, bidets and wall-hung basins that go with them. For a project buyer, buying ceramics from a one-stop supplier rather than from a single-product trader changes four things on the order.
One specification sheet instead of six. Basins, toilets, shower systems, vanity tops, lighting, flooring and wall panelling can be coordinated by one team, so glaze colour, metal finish and profile are matched across the room rather than reconciled at site level.
Custom and OEM options before production starts. Where a project needs a different finish, size or branding, that decision has to be made during prototyping. Our Custom & OEM Service covers bespoke finishes and private labelling, so changes are agreed with drawings rather than requested after the moulds are running.
Consolidated freight. Bathroom ceramics are heavy but low volume. Shipping them in the same container as joinery, flooring and furniture reduces handling and means one delivery window on site instead of several. Our Logistics & Door-to-Door Delivery service covers freight forwarding, customs paperwork and container loading.
One point of contact for snags. Replacement parts and post-handover issues are easier to resolve when the same supplier issued the packing list. Our Installation & After-sales Support service covers inspection, snag lists and spare parts.
Questions Project Buyers Ask Us Most
Can the 1003S be mixed with other models in one order?
Yes. A typical villa or hotel order takes stand basins for feature bathrooms and wall-hung basins for secondary bathrooms, with matching toilets throughout. Tell us the room schedule and we will price it as a suite.
What information should I send with an enquiry?
The bathroom layout or setting-out drawing, the quantity per model, the drain arrangement for each location, and your target delivery destination. With those four items we can confirm feasibility and quote without a round of clarifying emails.
Are dimensions on the product page final?
Use them for space planning, and request the current technical sheet before you issue construction drawings. Trap position and rough-in details in particular should be confirmed on the sheet that applies to your production run.
Do you ship bathroom ceramics to Australia?
We deliver door-to-door by sea, air or rail, and we have completed villa and apartment projects in Willoughby, Perth, North Turramurra, Melbourne and Sydney. Import terms, duties and delivery scope are confirmed per project on the quotation.
Send us your bathroom schedule
Email the room list, quantities and setting-out drawings for your project and we will confirm the 1003S fit, matching suite options and consolidated delivery to site.
Contact: PHILLIP | Phone / WhatsApp: +86-13928214007 | Email: santerson@qq.com
Enquiry page: Contact SANTERSON