A wardrobe order rarely goes wrong on the drawing. It goes wrong on the surface. Two panels can share a colour name, a board code and a supplier line, and still read differently once they are standing next to a window at 4pm. That is exactly why we ask every buyer to sign off physical matte finish melamine wardrobes samples before the boards are cut, edge-banded and packed. The sample is the cheapest quality control step in the whole programme, and it is the one most often skipped.
Below is the review routine our project team uses when a client is specifying melamine wardrobe panels for villas and apartment fit-outs — what to request, what to look at, and how to record the decision so that the delivered goods can be measured against it.
Start with the sample set, not a single panel
One A4 offcut tells you very little. Ask for a small set instead: the door or drawer-front material, the matching carcass board, the edge banding in the same décor, and one internal finish such as a shelf or back panel. Ordering them together lets you check how the tones sit against each other, which is where matte melamine is most often judged after installation. If your scheme also includes textured melamine wardrobes or a contrasting gloss detail, request those samples in the same batch so you are comparing finishes under identical light.
What to check on each sample
- Sheen under two light sources. Matte is a low-reflection surface, but the exact level of softness varies. Look at the panel under daylight from a window and under a warm LED downlight. Note whether the surface looks chalky, flat or slightly satin, and compare that with your expectation for the room.
- Colour cast. Greys, taupes and warm neutrals drift towards green, blue or pink depending on the décor batch and the light. Place two candidate samples side by side and decide which one you would live with, rather than judging each in isolation.
- Grain direction and repeat. For wood-effect melamine, confirm which way the grain runs on the door front and how it behaves on a wide panel. Then check that the direction is drawn correctly on your elevation, because grain cannot be changed after pressing.
- Edge banding match. Hold the loose edge band against the sample surface at arm's length and again up close. A band that reads a shade lighter than the board is one of the most common complaints on completed wardrobes.
- Surface feel and fingerprint behaviour. Run a clean, dry hand across the panel and leave it for a few minutes. Matte surfaces differ in how visibly oils and marks show, and this matters more on tall, frequently used doors than on upper cabinets.
- Mark resistance with items you actually use. Press a coin, a key and a ring against an offcut area. You are not looking for damage — melamine is a hard surface — but for whether the mark wipes away or stays visible.
- Clean-up test. Wipe the sample with a damp cloth, then with the cleaning product your maintenance team already uses. Anything left behind is a sign to change the cleaner, not the board.
Check the substrate and the build details the finish cannot show
A décor sample says nothing about what is behind it, so review that separately. Our melamine wardrobe panels are made to measure for each project, with the layout, material and finish specified at order stage. Confirm the board type you are being quoted, the panel thickness for doors and carcass, how the edges are closed, and the hardware set — hinges, slides, handles or a handleless profile. These decisions change cost and feel more than the colour does, and they are all agreed before production starts.
Also confirm how the unit meets the room: skirting boards, uneven walls, ceiling lines, and any recess. Our design and production coordination stage covers drawings and detail confirmation, so this is the point in the process where site conditions should be reflected on paper rather than solved on site.
Record the approval so it protects the order
- Label and keep the physical sample. Write the décor code, project name and approval date on the back with a permanent marker. Store it flat, out of direct sun, until handover.
- Photograph it once, properly. Shoot the approved sample next to your floor finish and wall colour in the room where the wardrobe will stand. One well-lit reference photo settles most later disagreements.
- Name one approver. A single person signs off the finish. Where an interior designer, a builder and an owner each pick a different panel, you get three opinions on site.
- Write down what is not included. Glass inserts, lighting, mirrors and metal trims are usually approved separately. Note that in your record so nothing is assumed.
A short pre-production checklist
| Check | Pass condition |
|---|---|
| Finish code on the sample and on the drawing match | Same décor code, same supplier reference, on paper |
| Sheen accepted under daylight and LED | No surprise shine or chalkiness at either light |
| Edge banding matches the board | No visible tone step at arm's length |
| Grain direction shown on elevations | Drawing states the run direction for every panel |
| Marks and cleaning test pass | Marks wipe away with your normal cleaner |
| Board type, thickness and hardware confirmed | All listed in the quotation you signed |
| Sample stored until handover | Labelled sample physically available on site |
Where this fits in a project timeline
Sample review belongs after the layout is agreed and before boards are ordered. If you are furnishing several rooms, do it together with the other melamine elements — matte melamine cabinets in the kitchen and laundry use the same review logic, and matching a wardrobe to cabinetry across rooms is far easier when both are approved from one sample batch. Once production starts, colour changes become rework; before it starts, they are a note on a drawing.
SANTERSON supplies made-to-measure wardrobe panels and the surrounding fit-out package — cabinetry, doors, wall and ceiling finishes, flooring, lighting and bathroom products — from our own factory, with door-to-door delivery, installation support and after-sales service. Send us your elevations and finish shortlist and we will ship a sample set for you to test on site before you confirm the order.