Noise travels through hard surfaces. In a hotel lobby, sound bounces off stone floors, glass partitions and high ceilings until conversations blur into one continuous hum. In a villa with open-plan living, the same problem shows up in a different form: the dining room carries the television, the study cannot stay quiet, and a home cinema fights with the HVAC system. Acoustic wall panels are one of the few fit-out elements that address both problems at once, because they change how a room sounds without changing how it looks. This guide walks through how to specify Santerson Acoustic Panels for hospitality and residential projects, what to decide before you request a quotation, and where sliding acoustic systems make more sense than fixed wall cladding.

Start With the Room, Not the Panel

Buyers often begin by asking which panel is "the best". The more useful question is what the room is doing wrong. Three failure modes cover most hotel and villa situations:

  • Reverberation. A large, hard-surfaced space where speech becomes unintelligible and footsteps ring out. Lobbies, banquet halls, restaurants, villa atriums and stairwells all behave this way. The fix is absorption on the surfaces that face each other.
  • Flanking transmission. Sound arriving through a shared wall rather than over or around it. Adjacent guest rooms, a villa home office next to a media room, and meeting suites sharing a corridor are typical cases. Panels mounted on the party wall reduce what passes through, but the detail has to be continuous — gaps at skirtings, reveals and service penetrations undo the work.
  • Impact noise. Trolleys, dropped luggage, chairs dragged across tile. This is a floor and ceiling conversation more than a wall one, and it should be identified early so the wall specification does not get blamed for it later.

Write down which of these you are solving before you look at finishes. A project that needs reverberation control in a lobby can carry decorative fabric or timber-look faces; a project addressing flanking transmission between rooms needs attention to substrate, fixings and joint detailing first.

Fixed Panels or Sliding Panels

SANTERSON lists two related product families under its wall systems, and choosing between them is usually a space-planning decision rather than an acoustic one.

Santerson Acoustic Panels sit in the Paneling Systems collection. They are fixed wall cladding: configured per space, with made-to-measure sizing and a choice of material and finish. Use them where the wall is permanent and the acoustic treatment should read as part of the design — behind a reception desk, along a guest-room headboard wall, across a villa media room, or on the hard surfaces of a corridor that runs past guest doors.

Santerson Acoustic Sliding Panels belong to the Sliding Panel Systems collection. They combine absorption with a moving element, which changes what the room can do. A conference suite that converts between two small meeting rooms and one boardroom needs a divider, not a fixed wall. A villa library that opens onto a family living area needs the acoustic boundary to close on demand. Where the plan has to flex, specify the sliding system and design the track and floor detail into the build early — retrofitting an overhead track into a finished ceiling is far more expensive than allowing for it.

Specifying to the Space

Both collections are configurable rather than catalog-standard: dimensions, layout, material and finish are set per project. That flexibility is what makes them workable across a mixed hospitality or villa package, but it also means the buyer has to supply real information. The practical specification decisions:

  • Where panels go. Mark the surfaces that face each other across the room, plus the party walls between quiet and noisy zones. Full-height coverage is usually simpler to detail than partial panels with a decorative reveal, because the reveal becomes an acoustic gap.
  • Panel size and module. Made-to-measure sizing lets you align panel joints with door reveals, headwall widths and furniture modules instead of accepting an arbitrary grid. Send openings and critical dimensions, not just room areas.
  • Finish. Panel faces in a hotel are handled constantly — luggage, cleaning carts, housekeeping trolleys, guest contact. Matte and textured faces hide handling marks better than high-glass surfaces; glass and glossy panel faces look sharp but show every fingerprint. In villas the finish usually follows the joinery language already running through the project.
  • Cleaning and maintenance access. Ask how the panel face is cleaned and whether removable sections allow access to services behind the wall.

Acoustic performance depends on the whole build-up — substrate, air cavity, fixings, joint sealing and the panel itself — not on the decorative face alone. Because these are configurable listings with limited published technical data, request the performance figures for the exact configuration you are ordering and check them against the requirement your consultant set. A panel that performs well in a test rig can still underperform on site if the perimeter is left unsealed.

Ordering Inside a Larger Fit-out Package

Acoustic panels rarely arrive alone. In a hotel or villa project they are one line among flooring, joinery, doors, lighting and furniture, and the sequencing matters: wall cladding that is ordered late tends to be detailed badly, because the floor levels, door positions and service routes have already been fixed by other trades.

Sourcing panels alongside the rest of the package through one turnkey furniture and fit-out supplier removes a whole category of coordination risk. Santerson works as a China-based furniture and building materials manufacturer supplying hospitality, villa and office projects, with custom/OEM production, door-to-door logistics and installation support under the same contract. In practice that means the acoustic panels, the wall-mounted joinery next to them, and the doors that meet them can be dimensioned against one set of drawings rather than three. For projects in Australia and elsewhere, this single point of contact is where most of the value sits — one production schedule, one shipment plan, one snag list at handover.

A Practical Checklist Before You Request a Quotation

  • The acoustic problem named in writing: reverberation, transmission or impact.
  • Room dimensions, ceiling heights and all openings, with critical alignment dimensions called out.
  • Fixed or sliding — and if sliding, the track position and floor detail.
  • Finish selection matched to traffic level and housekeeping routine.
  • The performance figures required by your acoustic consultant, sent with the enquiry rather than checked afterwards.
  • Delivery address, site access constraints and installation scope confirmed against what the contract actually covers.

Work through those six points before you send an enquiry and the quotation comes back usable on the first pass. Send your drawings and room schedule to SANTERSON's project team, and the panel configuration, finish and sizing can be set against your actual spaces instead of a standard catalogue module.