High gloss wood effect cabinets look decisive on a rendering and difficult to control on site. The finish shows every misalignment, the grain pattern has a direction, and the panel size that fits the drawing is not always the panel size that fits the opening once services are in the way. Procurement teams who get this product right do it on paper first: they fix the specification before production starts, so the number of variables left to argue about during installation stays small.

The list below is what a purchasing team should be able to point to for every run of high gloss wood effect cabinets on a villa, apartment or hospitality fit-out — and what should be in writing before the first panel is cut.

1. The exact finish reference, not a finish name

"Wood effect" covers a wide range of tones and grain styles, and a colour name in an email is worth nothing twelve months later when a replacement door is needed for one damaged unit. Record the manufacturer's finish or board code, the gloss level as stated by the supplier, and the sheen you actually approved on a physical sample. Photograph the approved sample next to a neutral card and file the photo with the purchase order.

Then state where that reference came from. SANTERSON's high gloss wood effect cabinets sit within the wider custom kitchen cabinets for residential and hotel projects range, where finish, layout and dimensions are specified per project rather than chosen from a fixed shelf. That flexibility is useful, but it means the approved reference has to be captured in your documents, because there is no standard SKU to fall back on.

2. Grain direction and panel orientation, drawn per elevation

Wood effect finishes have a grain direction. If the drawing does not say which way the grain runs on each door, drawer front and side panel, the factory will make a reasonable assumption and someone on site will call it a defect. Document the grain direction on every elevation, mark book-matched pairs where you want them, and note whether horizontal panels run with the long edge.

Also record which faces are visible. A tall housing next to an open walkway may need two decorated faces; a housing boxed into a run may only need one. That decision changes cost and it should be made by you, not by whoever packs the crate.

3. Confirmed dimensions from a site survey, not a drawing grid

Made-to-measure sizing is one of the configuration options listed for these cabinets, which removes the excuse for gaps and scribe panels added on site. Document the as-built dimensions taken after floors are level, walls are plastered and services are fixed — not the dimensions from a design-stage plan. Note floor levels at both ends of the run, ceiling height variation, and the position of soil pipes, flues and electrical outlets.

For each run, record the clear opening width and height, the finished floor level, and any tolerance you have allowed. If a wall is out of plumb, say so in the order rather than expecting the installation crew to solve it with silicone.

4. Layout, interface details and appliance schedule

Layout is tailored per project, so the procurement file should carry a signed layout drawing showing door swing direction, handle or handleless detail, drawer stack heights, and where tall units sit relative to circulation. Then attach the appliance schedule: model numbers, cut-out dimensions, ventilation requirements and door relief for ovens, dishwashers, fridges and wine cabinets.

Integrated appliances are where high gloss runs usually go wrong, because a 3 mm error in a cut-out is invisible on a matte panel and obvious against a reflective one. Keep the appliance schedule and the cabinet elevation in the same revision-controlled document set.

5. Substrate, edge treatment and hardware

The product page offers material and finish options without committing to one construction, so the specification has to state what you selected: door substrate, edge banding or wrap detail on high gloss edges, carcass board and thickness, back panel fixing, and soft-close hinges and runners with their brand and model. Edge treatment matters more than most buyers expect — a reflective door with a visible seam line at the edge reads as poor quality from one metre away.

Record the load rating for drawers, the hinge count per door for tall units, and whether you want integrated or concealed handles on a handleless high gloss detail. Hardware substitutions are common when an order crosses borders; naming the model in the order makes substitution something you approve rather than discover.

6. Sample approval and sign-off before production

Before releasing production, document a sample approval sheet: the physical sample reference, who approved it, the date, and the conditions it was viewed under. A high gloss surface reviewed under warehouse lighting behaves differently from the same surface under warm LED downlights in a completed kitchen.

A practical rule: no production release without a signed sheet covering finish reference, grain direction, panel dimensions, edge detail and hardware model. Those five items account for most of the disputes on this product category.

7. Packaging, packing list and receiving checks

High gloss panels are usually protected with film and corner protection, and the packing detail should be documented in the order: edge protectors, interleave sheets, panel orientation in the crate, and the marking system that links each carton to an elevation number. On arrival, photograph the crates before opening, then check contents against the packing list while the container is still on site.

Record film condition, any delamination of protective film, and chipped edges at receiving rather than after installation. SANTERSON's logistics and door-to-door delivery service covers freight forwarding, packaging and container loading, customs paperwork and shipment tracking — your receiving notes are what make a claim on transit damage straightforward instead of debatable.

8. Storage and handling conditions on site

Document where panels are stored between delivery and installation: indoors, dry, acclimatised to the building, kept upright or flat on a level base, and not left in a sealed crate on a damp slab. High gloss faces scratch from panels sliding against each other, so handling instructions belong in the site programme alongside the trades' access dates.

9. Installation sequence, interface tolerances and snag list

Write down who sets out the run, who levels the carcasses, and what happens between cabinet edges and adjacent worktops, splashbacks and wall finishes. State the gap you expect between doors, the acceptable variation across a run, and how scribe panels are finished. Then inspect with a light test: shine a lamp along the front of the run and check reflections for misalignment before signing off.

Keep the snag list itemised by unit number, photographed, and dated. The site's installation and after-sales scope covers on-site installation, inspection and snags, spare parts and maintenance; your documented snag list is what makes that follow-up specific.

10. Care instructions and cleaning products to avoid

Record what the supplier says about cleaning high gloss surfaces, including which products to keep off them — abrasive pads, scouring powders and solvent-based cleaners are the usual culprits. Issue that note to the client or the facilities team at handover. Fingerprints and light marks on a glossy wood effect door are often a cleaning-method problem rather than a finish problem, and it is cheaper to document the method than to replace doors.

11. Commercial terms and change control

Document what the quoted price includes: drawings, sampling, packaging, freight mode and Incoterms, duties, and the scope of installation if you are buying it. Note lead time expectations as stated by the supplier for this order, and keep every revision of the layout drawing with a date and reason for change.

Most cost creep on cabinetry comes from verbal changes — a moved oven housing, a taller tall unit, an extra drawer. Change control in writing, with the price effect recorded at the time, keeps the final account predictable.

A procurement checklist you can paste into a specification

Item to documentWhat "done" looks like
Finish referenceSupplier code plus photographed approved sample, filed with the order
Grain directionMarked on every elevation, book-matched pairs identified
DimensionsSite-surveyed clear openings, recorded floor levels and allowed tolerances
LayoutSigned elevation set with door swings, handle detail and drawer stack heights
AppliancesModel numbers, cut-out dimensions, ventilation and door relief scheduled
ConstructionSubstrate, decorated faces, edge treatment and carcass board named
HardwareBrand and model for hinges, runners and handles; substitutions require approval
Approval gateSigned sample approval sheet before production release
PackagingProtection method and carton-to-elevation marking stated in the order
ReceivingPhotographed crates, contents checked against packing list, damage logged same day
StorageDry indoor storage, acclimatised, protected faces not rubbing
InstallationSetting-out responsibility, door gap standard, light test before sign-off
Snags and after-salesItemised snag list by unit number with dated photographs
CareCleaning method and prohibited products issued at handover
Commercial termsInclusions, Incoterms, duties, lead time and dated revision history

Frequently asked questions

Is a high gloss wood effect finish suitable for a busy family kitchen or a rental property?

It takes fingerprints and light marks more visibly than a matte surface, so the question is really about cleaning discipline. In a rental or high-traffic unit, document the care instructions at handover and consider whether a lower-sheen wood effect finish reduces maintenance calls. Both options exist within the same cabinetry range.

Should I order a physical sample for every colour in a multi-unit project?

Order one sample per finish used, and view it in the actual room lighting before approval. For apartment projects with repeated kitchen types, approve the sample once, record the reference, and keep the approved sample itself as the benchmark for later phases.

What is the single most useful document to insist on?

A dimensioned elevation set based on a site survey, with grain direction marked on each panel. Almost every other problem in this category — gaps, mismatched grain, cut-outs in the wrong place — traces back to panels made from design-stage dimensions instead of as-built ones.

SANTERSON has operated since 2008 as a China-based manufacturer and one-stop supplier of furniture and building materials for villa, hospitality and office projects, with custom and OEM cabinetry available through its custom and OEM service. If you want the specification above checked against what the factory can actually produce, send your elevations and finish references to the team on the contact page and have them confirmed in writing before production release.