A square hot spa with a waterfall and underwater lighting is easy to specify on a drawing and surprisingly easy to get wrong on site. The shape reads clean against a villa terrace or pool deck, the waterfall gives it presence, and LED lighting makes it usable after dark. What usually causes rework is not the concept — it is the finish detail that nobody wrote down: which shell material, which frame, which pumps, how many lights, where the power sits, and what the cabinet is exposed to.
This article walks through the finish details a purchaser should confirm before ordering a square luxury hot spa with waterfall feature and LED lighting, using our own product data as the worked example. Every figure below comes from catalogue entries we publish on this site; anything we cannot confirm for a given configuration is flagged rather than guessed.
Start With the Shell, Frame and Cabinet — Not the Water Features
The visible water features are the selling point, but they sit on top of three structural decisions that determine how long the spa lasts outdoors. Our square hot spa is built on a #304 stainless steel metal frame for support, with a sealed base, a moisture-free cabinet and an isolated power layout. Those four items are worth restating in your purchase order because they are exactly what an outdoor spa is tested against: standing water underneath, humidity inside the cabinet, and electrical equipment sharing space with both.
Across our wider swim and hydrotherapy range, shells are specified as acrylic, and cabinets appear in finishes such as wood-look or a plain grey exterior. Cabinet finish is a project decision, not a catalogue default — on a villa deck you may want it to read as joinery that matches nearby cladding, while a resort installation may prioritise a finish that takes direct sun and salt air without complaint. Ask for the cabinet material and finish by name in writing, and confirm which finishes are offered for the specific model you are ordering.
Detail to lock down before production: frame grade, shell material, base sealing method, cabinet material and finish, and how the power compartment is separated from the wet side. If your quotation lists only "spa, square, with waterfall and LED", it is not yet a specification.
Waterfall Detail: Height, Spill Edge and Where the Water Lands
"Waterfall feature" covers several different builds. Some units use a sheet or lip waterfall that spills across the spa wall into the water; others combine a waterfall with vertical water columns aimed at the back or shoulder area. Our catalogue distinguishes these: the WS-S04 is listed with a waterfall, and the WS-S06 is listed with a waterfall plus 4 water columns, while the WS-S38 shows a waterfall with 6 water columns. That difference changes pump count, splash behaviour, and how much of the rim you can actually sit behind.
Confirm three things on the drawing: the height and projection of the spill edge relative to the coping; whether the waterfall is fed by a dedicated pump or shared with the jet circuit; and where the falling water lands, because that determines splash zone and how much deck finishes around the spa get wet. On a timber or composite deck, splash distance decides board selection and drainage falls. On stone or tile, it decides slip rating and joint detailing.
LED Lighting: Count, Position and Control
Lighting is where buyers most often accept vague wording. Our listings state LED counts precisely because placement changes the effect: WS-S04 shows 3 LED lights plus 18 small LED lights; WS-S06 shows 2 plus 18 small; WS-S38 shows 4 plus 12 small; and the longer swim models such as WS-SP500 and WS-SP600 show 4. A spa lit by three fixtures in a square shell will not read the same as one with four fixtures plus a ring of small points along a step or bench.
Ask for a lighting layout, not just a fixture count: where each light is embedded, whether any light faces the waterfall so the falling sheet carries colour, whether the small LED points are on steps or under a bench lip, and what control the buyer gets — single colour temperature, colour change, or scenes tied to the pump circuits. Also confirm how fixtures are accessed for service. A light embedded in an acrylic shell with no access panel becomes a drainage problem later.
Pumps, Jets and Ozone: Read the Configuration, Not the Model Name
Jet count is not comparable across models without looking at pump allocation. In our data, WS-S04 lists 3 water pumps, 1 filter pump and 26 jets plus 4 water columns; WS-S06 lists 2 water pumps, 1 filter pump and 56 jets; WS-S38 lists 3 water pumps, 1 filter pump and 51 jets with 6 water columns. A higher jet number on fewer pumps will feel different in use from a lower jet count with more pumps behind it, so compare the pair of numbers rather than the headline.
Our square hot spa description covers a massage pump, a circulation pump and an optional air blower. "Optional" matters: an air system changes the seat feel and adds its own plumbing and control point, and it is cheaper to include at build than to retrofit. Ozone appears as a listed feature across the range, and UV sterilisation appears in our options list alongside heat pumps, water pumps, sand filtration, insulation, steps and control systems. Confirm which of these are in your price and which are add-ons.
| Model | Catalogue dimensions (mm) | Pumps | Jets | LED lights | Total power |
|---|---|---|---|---|---|
| WS-S38 | 3760 × 2080 × 1110 | 3 water + 1 filter | 51 jets; 6 water columns | 4 + 12 small | 14.05 kW |
| WS-S04 | 4090 × 2200 × 1110 | 3 water + 1 filter | 26 jets; 4 water columns | 3 + 18 small | 8.25 kW |
| WS-S06 | 5820 × 2220 × 1110 | 2 water + 1 filter | 56 jets | 2 + 18 small | 6.35 kW |
| WS-SP500 | 5000 × 2500 × 1600 | Water pump not listed; 1 filter | 6 jets | 4 | 9.35 kW |
| WS-SP600 | 5900 × 2500 × 1600 | Water pump not listed; 1 filter | 6 jets | 4 | 9.35 kW |
| WS-SP600-MS | 5900 × 2500 × 1600 | 1 water + 1 filter | 29 jets | 4 | 11.55 kW |
| WS-S12 | 11740 × 2200 × 1470 | 2 water + 1 filter | 73 jets | 1 + 50 small | 7.65 kW |
These are catalogue figures for the configurations shown on our product pages, not a promise that any two units ship identically. Where a cell above reads "not listed", that equipment was simply absent from the specification block we captured for that model — confirm it with us before you rely on it.
Power, Insulation and the Electrical Boundary
Total power is a design input for the electrician, not a footnote. The figures above run from 6.35 kW to 14.05 kW depending on model and equipment set, and a heat pump — offered as an option across the range — changes both the load and the circuit protection you need. Confirm supply voltage and phase for your site, the required circuit rating, earthing and RCD/RCBO arrangement, isolator location, and cable routes before the deck is closed up.
Our square hot spa specifies an isolated power layout, which is the right instinct for an outdoor unit, but the interface on your side still needs detailing: where the control system sits relative to the seating area, whether the control panel is reachable with a wet hand, and how the cable entry is sealed. Insulation is also listed as an option in our accessories list, and it matters more than buyers expect once the spa runs outside a heated room — ask what is insulated, to what thickness, and whether the cabinet base is included.
Shape Options If Square Does Not Fit the Deck
Square is not always the right answer. Our customizable shape outdoor spa supports square, round, oval and curved shells with an acrylic shell and balanced structural reinforcement, so a tight corner or a curved pool edge does not force you into a compromise. If your project needs hydrotherapy plus a swimming lane, the range splits differently — see our luxury outdoor swim spa with massage jets, LED and water features and the long outdoor swim spa with a hydrotherapy relaxation pool, which pair a swimming channel with a separate relaxation end. For a circular seating layout, our round outdoor hot tub spa with hydrotherapy jets and underwater LED lights uses an acrylic shell with a wood-look cabinet.
All of these sit inside our swimming pools and swim spas category, alongside the individual model pages for each configuration.
Site Prep: Substrate, Access and Craning
A spa arrives as a delivered unit that must land on a prepared support. Confirm the bearing arrangement your site provides — full slab, perimeter beam, or a pedestal frame under an accessible deck — and confirm the load path with your structural engineer using the delivered weight of the filled unit, not the empty shell. Deck heights should be set so the rim is comfortable to sit over and so any access panel to pumps and control gear can actually be opened after the finish is laid.
Then check the route. A 5900 × 2500 mm shell will not pass through a side gate, and rooftop or courtyard positions may need a crane or hiab. Send us photos of the access path and the finished level early; we coordinate packaging and container loading as part of our logistics service, and an access problem solved at quotation stage costs nothing.
How We Confirm These Details on a Project
For project buyers, this is where a single supplier helps. Our services run through consultation, design and planning, production, logistics, installation and after-sales in one workflow, and our custom and OEM service covers bespoke finishes and configurations where a standard catalogue model is close but not exact. Our logistics and door-to-door delivery service handles freight, documentation and container loading; our installation and after-sales support covers on-site fitting, inspection and spare parts. Because the same team produces the shell, cabinet, water system and lighting layout, the finish details above get resolved in one specification sheet rather than across four vendors.
We have delivered villa and hospitality packages in Australian projects including Willoughby, Perth, North Turramurra, Melbourne and Sydney, so a spa specified for an Australian deck is coordinated with the same joinery, cladding, lighting and outdoor furniture package rather than shipped as an isolated item.
Frequently Asked Questions
Is the waterfall on a square hot spa always included?
No. Waterfall appears as a listed feature on some models and not others, and some units pair it with water columns. Read the feature list for the exact model you are quoting.
Can I order a square spa in a custom size?
Our range supports customised shapes including square, round, oval and curved, and our custom/OEM service covers bespoke finishes. Send the deck dimensions and finished level and we will confirm what is feasible for that configuration.
What power do I need to allow?
Catalogue total power across the models listed above ranges from 6.35 kW to 14.05 kW, and adding a heat pump changes the load. Allow the circuit from the confirmed configuration for your site, not from a catalogue average.
Are LED counts fixed?
They vary by model — from 2 large plus 18 small on one shell to 4 plus a swim-channel layout on another. Ask for the lighting layout drawing rather than accepting a number.
If you are specifying a square hot spa with waterfall and LED lighting for a villa, resort or hospitality project, send us the deck layout, the finished level and your electrical supply details. We will confirm shell, frame, cabinet finish, pump allocation, jet count, LED placement and insulation for that exact configuration before production begins.