Stone and marble read as the most permanent finishes in a project, which is exactly why they are specified so early — and revised so often later. A bathroom vanity top approved at concept stage may reappear in tender as a wall cladding, a splash zone, a reception counter or a poolside table, each with different fixing details and different shop-drawing needs. Writing the specification properly at the start is what keeps those changes from turning into variation orders.

This guide sets out how to brief Santerson stone & marble surfaces so that the quotation you receive is the one you can build against — what to state, what to leave open, and where the usual disputes come from.

Start with where the material actually has to perform

Before naming a stone, list every location it will appear in and what each location demands of it. A horizontal surface that carries water and cosmetics behaves differently from a vertical panel behind a shower, which behaves differently again from a decorative screen in a lobby. Group the surfaces by exposure rather than by room.

  • ●Horizontal worktops and vanities — edge profile, cut-outs for basins and taps, overhang, joint positions.
  • ●Wet walls and splash zones — panel joints, waterproofing interface, access to services behind the panel.
  • ●Feature and full-height cladding — substrate preparation, fixing method, panel sizes relative to ceiling heights.
  • ●Outdoor and semi-exposed settings — where the brief should say explicitly that performance in that climate still needs confirming.

Once the surfaces are grouped this way, the rest of the brief becomes a set of answers per group rather than one long wish list.

What to put in the written brief

Santerson's stone and marble ranges are supplied made to measure, with material, finish and layout set per project. That flexibility is useful only if the brief carries enough information to price and draw from. A short specification sheet per surface group is usually enough.

Item to stateWhy it matters at quotation stage
Location, room and drawing referenceTies each panel or top to a coordinated drawing instead of a photograph.
Overall dimensions and thickness requiredThickness drives both cost and the detailing of edges, supports and returns.
Finish — polished, honed or texturedThe same material reads very differently in a bathroom than on a feature wall.
Cut-outs, joints and edge profilesBasin type, tap holes and mitred returns are the most common late additions.
Panel layout and joint patternDetermines slab yield, waste and how veining is matched across a run.
Fixing method and substrateCladding needs to be drawn against the wall build-up, not assumed.
Quantity and phasing of the packageLets production and delivery follow the site sequence rather than one drop.
Delivery destination and access constraintsPanel sizes have to fit lifts, stairwells and doors on site.
Where a decision is genuinely open — the stone species, or whether a vanity top becomes an integrated basin — say so in the brief and ask for two priced options. An unspecified item that quietly defaults to something else causes more rework than an open question.

Keep surfaces and panels on one drawing set

Stone in a project rarely stays in one trade. Countertops and basins sit under sanitary fit-out; wall cladding sits under partitions and paneling. In practice the same material has to be cut, finished and matched across both. Santerson's stone & marble panels are configured with made-to-measure sizing and finish options in the same way as the countertop surfaces, so requesting both from one supplier lets the veining, thickness and finish be coordinated across the two packages instead of reconciled on site.

Ask for a single setting-out drawing that shows vanity tops, wall panels and any adjacent finishes together. That single sheet resolves most arguments about where joints land and who is responsible for the substrate behind them.

Where stone packages normally go wrong

  • ●Site dimensions taken too early. Plasterboard, waterproofing and back-boxes all change the finished face. Measure after those trades are set out, or state clearly that final dimensions will be re-surveyed.
  • ●Cut-outs left to the installer. A top delivered without basin and tap cut-outs usually means cutting on site, which is where chipped edges appear.
  • ●No approved visual reference. Veining varies within one material. Agree a sample or photograph that both sides sign off before production.
  • ●Fixing details assumed. Cladding panels need the wall build-up, substrate and fixing method shown on drawings before they can be fabricated to size.
  • ●One delivery for a phased site. Large panels with nowhere to go become a storage and damage problem; phase the package with the programme.

How custom work fits the procurement route

Made-to-measure stone usually arrives alongside other bespoke elements — cabinetry, joinery, vanities and screens — and those packages share dimensions, site levels and a delivery sequence. Santerson is a China-based furniture and building materials manufacturer working on villa, hospitality and office projects, with custom and OEM service covering design, prototyping and material selection, plus logistics and door-to-door delivery for the combined package. Consolidating stone with the joinery and fixture packages under one procurement route removes the coordination gap between suppliers, which is where most stone defects are actually traced back to.

The practical benefit is narrow but real: one setting-out drawing, one survey date, one container sequence and one point of contact for snags. Confirm scope, dimensions and the specifications selected for your project at detail-confirmation stage, before production starts.

A short checklist before you send the enquiry

  • ●Every stone surface listed by exposure, not by room.
  • ●Dimensions, thickness, finish and edge profile stated per item.
  • ●Cut-outs, joints and panel layout shown on a drawing reference.
  • ●Fixing method and substrate identified for all cladding.
  • ●Open decisions flagged as priced options rather than left blank.
  • ●Delivery destination, access limits and phasing included.

Send that and the quotation comes back comparable line by line — and the stone package arrives on site cut, finished and ready to fix.