A wall panel sample looks convincing on a desk and disappointing on a wall. The difference is rarely the panel alone — it is what sits behind the quotation. If you are specifying wall finishes for a villa, hotel or office fit-out and holding two or three proposals in front of you, here is what to line up side by side before you place an order.
Start with the scope of supply, not the price per square metre
Two quotations for the same wall area can differ by a wide margin because they include different things. Before you compare any unit rates, write down what each supplier is actually responsible for. A complete wall panel systems scope covers the panels themselves, the substrate or fixing method, trims and edge profiles, any integrated lighting or electrical provisions, hardware for sliding or door elements, and the drawings your site team will build from.
A low rate often means some of those lines have been moved out of scope and will appear later as variations. Ask each supplier to state in writing which items are included and which are excluded. If one proposal lists trims and another does not, you are not comparing the same product.
Compare like for like across three panel families
In project procurement, wall panels fall into three groups, and each is judged on different criteria. Mixing them in one price table is the fastest way to make a bad decision.
| Family | Typical use | What to check on the sample |
|---|---|---|
| Configurable interior systems — veneer, textured, matte lacquer, stone and marble, glass and glossy finishes | Feature walls, headboard walls, media walls, concealed storage fronts in villas and guest rooms | Colour and grain match against the approved finish board; joint detail; how corners and reveals are closed |
| Decorative and 3D wall panels for interior renovation | Lobby feature walls, restaurant and office backgrounds, bedroom accent walls | Pattern repeat, panel thickness, how the surface behaves at edges and cut-outs |
| Cladding panels for facades and high-traffic interiors — aluminium honeycomb panels and thin bendable stone-look sheets | Facades and curtain-wall lines; renovation over existing substrates; columns, arches and curved walls inside the building | Flatness across a large area, behaviour when wrapped around a curve, edge treatment, fixing method on site |
Where the wall curves — an arched niche, a column, a rounded reception desk front — a rigid board is the wrong answer no matter how good its finish looks. Thin bendable cladding sheets can be cut and wrapped onto curved surfaces, which removes the cost of fabricating a curved substrate. Where the wall must read as one flat plane with hidden storage behind it, the panel is really part of a joinery system, so the door detail matters more than the surface. That is the point at which a door and panelling package, drawn together from the start, beats two separate orders that never quite line up.
Read the specification block, not the marketing paragraph
Most product pages describe finishes well and dimensions poorly. For each line item, ask for a specification sheet that states:
- Panel size and thickness as supplied, plus the tolerance you should expect on site
- Substrate or core construction, and the finish layer — veneer, lacquer, laminate, stone veneer, coated metal
- Whether sizing is made to measure from your drawings, or fixed modules you must design around
- Fixing method and adhesive or mechanical system, including what the substrate must be before installation
- For any panel near a light source or behind a television: how heat and wiring provisions are handled
Where a page lists moisture resistance, fire performance or weather resistance without test values attached to the specific product, treat it as a question for the supplier rather than a fact for your specification. A manufacturer who intends the claim to stand will confirm it against the exact configuration you are ordering.
Judge the drawing package before you judge the price
For custom wall work, the proposal should come with drawings — not only a rendering. Ask for setting-out plans showing panel breaks and joint positions, elevations with dimensions, sections through the important junctions (floor line, ceiling line, inside corner, door reveal), and a schedule naming every finish code. A rendering tells you what the room will look like; a drawing tells you whether it can be built.
Then compare how each supplier handles coordination with other trades. Wall panels meet electrical outlets, air diffusers, skirting, door frames and sometimes integrated lighting. The proposal that shows these junctions resolved on paper will save money later; the one that leaves them to site decisions usually does not.
Check what happens between the factory and your site
Wall panels are bulky, and damage in transit is a common cause of schedule slippage. Ask each supplier to describe packaging and loading for your volume, the Incoterms being quoted, and how panels are packed so that the pieces needed first arrive first. If you are sourcing wall finishes alongside other fit-out items from one one-stop furniture and building materials supplier, confirm who prepares shipping documents, who clears customs at destination, and whether the different trades' deliveries are sequenced to suit your site programme.
Then check installation. Find out whether the supplier provides installation guidance, a site briefing or an installer team, and how snags are handled after handover. If panels arrive before the substrate is ready, on-site storage becomes your cost. Sequencing deliveries by room rather than shipping everything at once is worth requesting.
Score the samples on four tests
When physical samples arrive, test them in the actual space rather than under a showroom light:
- Colour under your lighting. Check at day, at evening and under the specified fixtures. Veneer and metallic lacquers shift noticeably with light temperature.
- The joint. Put two samples edge to edge and look at the seam straight on and from a grazing angle. Joint detail decides whether a wall reads as crafted or as boards stuck up.
- A cut edge. Cut the sample with the tool your installers will use and inspect chipping, edge banding and how the core looks at the reveal.
- A curve or corner, if relevant. Bend a flexible sheet around a radius matching your design and check whether the surface crazes or lifts.
Keep the approved samples, signed and dated by both parties, as the reference for inspection on delivery. A colour or texture dispute is settled far more easily by physical approval than by photographs.
The questions that separate a serious proposal from a thin one
- Which panel line is being quoted, by exact name and finish code?
- Is the sizing made to measure, and who takes the site dimensions?
- What is included for trims, corners, and junctions with doors and skirting?
- How are integrated lighting or media provisions handled inside the panel build?
- What lead time applies to the approved finish, not just to the category?
- If panels arrive damaged or off-tone, who pays for replacement and freight?
A supplier who answers these precisely is usually easier to work with than the one quoting the lowest rate per square metre.
If you want a full wall scope quoted — panels, joinery, concealed doors and integrated lighting drawn as one package — send us your drawings and we will return a setting-out proposal with finish samples for approval. Enquiries: santerson.com/contact.
Configurable wall systems are made to measure; dimensions, finishes and performance claims are confirmed against the exact specification selected for each project.