A long arm sconce looks simple on a mood board and complicated on a purchase order. In guest rooms and study areas, the same fitting has to clear a headboard, light a desk without glare, survive housekeeping, and arrive with the rest of the joinery package in the right quantity. This guide walks through how we plan that buy at SANTERSON for hospitality projects, using our Modern Balance Arm Wall Lamp, Minimalist Long Arm Sconce for Living Room & Study as the worked example.

Start with the room drawing, not the lighting catalogue

Before any quantity is agreed, mark the fixing line on the room elevation. On our balance arm wall lamp the detail that decides everything downstream is the extended balanced arm: the circular wall base stays fixed while the arm reaches out over the surface below it and the light head adjusts to direct the beam. That geometry sets three dimensions you need on your schedule:

  • Wall base position relative to the headboard, desk edge or mirror, measured from finished floor level.
  • Arm reach and how far the head sits over the surface it serves, checked against the actual furniture depth you have specified.
  • Switch and cable route — whether the fitting is switched at the fitting, on a wall plate, or via a bedside control panel, which changes the back-box and first-fix layout.

Getting these three numbers from the drawing rather than from a sample saves the most common rework we see: sconces installed before the headboards arrive, then sitting behind them.

Technical data to request in writing for every guest room type

Marketing pages rarely carry the figures a consultant needs. For each fitting on your schedule, ask the factory to confirm the following in writing, per configuration, and hold that sheet against the approved sample:

Item to confirmWhy it matters on site
Lumens, wattage and colour temperatureDetermines whether the fitting reads as task light for reading and writing or as ambient accent; also drives consistency between room types.
Dimming method and driver compatibilityMust match the control system already in the project — trailing edge, 0–10 V, DALI or a bedside panel.
Electrical rating and destination-country complianceVoltage and certification requirements differ by market; confirm against the local authority and consultant specification, not from a datasheet copied across projects.
Fixing method and load-bearing substratePlasterboard, timber batten and masonry need different anchors and blocking; specify at first fix.
Finish construction and cleaning regimeMetal, glass and plated finishes take housekeeping chemicals differently; agree the cleaning product before handover.
Spare-part availability for the head, arm and shadeFixtures in guest rooms get replaced one at a time over years of operation.

Our own product pages do not publish these values as fixed numbers, because they are set per project configuration. Treat any figure quoted in a brochure as unconfirmed until it appears on the specification sheet you approve.

Mock-up one room before releasing the order

For fitting types like the Minimalist Long Arm Sconce, we recommend a single mock-up room or a sample wall for client and consultant sign-off. Check four things while it is installed:

  • Glare — view the head from the bed, the desk and the doorway. An adjustable light head helps here, but only if the aim range covers where people actually sit.
  • Beam spill — confirm the light falls on the intended surface and does not wash the artwork or mirror beside it.
  • Arm clearance — verify the reach against the real headboard depth, desk overhang or wardrobe reveal.
  • Switch feel and operation — the daily-use detail clients comment on most.

Build the schedule by room type, then add a spares line

Quantities go wrong when lighting is counted from a fixture legend instead of from room types. Take each room type — standard guest room, suite, study, corridor feature wall — list the fitting per type, and multiply by the count on the room schedule. Then add a spares allowance for the life of the asset, not just for installation breakages. Fixtures ordered alongside Lighting Products in one package are easier to keep consistent than fittings bought in separate lots across phases.

Where a project mixes fitting families, we usually group them by the surface they sit on rather than by style: sconces for guest-room walls and studies, vanity and mirror lighting for bathrooms, and integrated lighting inside joinery. Our Santerson Wall Sconces range is configured per project on finish, layout and dimensions, which is how a single sconce family stays consistent across guest rooms and bathrooms without changing the wall detail.

Consolidate the lighting buy with joinery and casegoods

Wall-mounted fixtures interact with cabinetry, headboard panels and reveals more often than they interact with other lights. Ordering sconces together with bespoke casework through our Custom & OEM Service means one party coordinates the blocking, the cable route, the reveal dimension and the finish match. As a one-stop project furnishing supplier, SANTERSON produces and sources furniture and building materials under one project package — cabinetry, wall panelling, loose furniture, sanitaryware and lighting — so the wall elevation is resolved once instead of in three separate trades.

What we need from you to quote

  1. The room schedule and elevations showing fixing heights and furniture depths.
  2. Your lighting specification, including dimming and control system.
  3. Destination country, so electrical rating and compliance can be confirmed for that market.
  4. Target handover date, working back through production and door-to-door delivery.

Send those four items and we will return a configuration sheet, a per-room-type schedule with quantities, and a lead time you can build the programme around. Sample rooms can be arranged before the full order is released.