A tall cabinet that looks right on a rendering can still fail on site: it fouls a door swing, hides a shut-off valve, or arrives without the shelf layout the client actually asked for. Most of those problems trace back to an incomplete specification rather than to manufacturing. If you are specifying Santerson Utility Tall Cabinets for a residential project, the pages describe them as configurable units whose finish, layout and dimensions are set per project — which means the burden of definition sits with whoever issues the specification. The checklist below follows the order we find works in practice: room and use first, then envelope and interface, then internal configuration, then finish and hardware, and finally the coordination items that decide whether the unit installs cleanly.

Start with the room and the job the cabinet has to do

Write down who uses the space and what goes into the unit before you draw anything. A utility tall cabinet in a family bathroom is asked to hold linens, toiletries and cleaning products; the same footprint beside a laundry may need to take bulky supplies, an ironing board, or detergents that should sit above child height. That list drives everything downstream — shelf heights, drawer versus open storage, whether the lower zone should be closed, and where the handles end up.

Note the items you know are coming, with their rough sizes: a hoover, a stack of bath towels, a hamper, a bottle of something tall. You do not need exact dimensions for every object, but you do need to know which items must be concealed and which can sit in the open. If the room also carries appliances, check whether the appliance zone belongs in this unit or in Santerson Integrated Appliance Tall Cabinets instead; appliance integration brings ventilation and electrical requirements that are easier to resolve on paper than after the carcass is fixed to the wall.

Fix the envelope: dimensions, wall conditions and clearances

The product information for this collection states made-to-measure sizing with material and finish options, so treat the opening as a specified dimension rather than an assumed standard one. Record width, height and depth of the intended position, and state clearly whether the given depth is to the carcass face or includes door fronts and handles.

Then record what the envelope has to deal with:

  • Floor finish build-up and where tiling stops, so the plinth or base sits on a known level.
  • Wall construction — masonry, stud, or tiled substrate — and whether any reinforcement or blocking is needed for wall-mounted components.
  • Ceiling condition: a flat slab, a dropped ceiling, or a bulkhead with services behind it. Confirm the clear height before specifying a full-height unit.
  • Door and drawer swing paths against the room door, an adjacent vanity, and any recessed alcove you intend to build into.
  • Outlets, switches, towel rails, pipework and shut-off valves that must remain reachable after installation.

Where the unit sits in a corner or wraps two walls, compare against Santerson Corner Tall Cabinets and state which solution you are buying; corner geometry changes both the carcass plan and what is genuinely reachable inside. Specify tolerances as well as dimensions — out-of-plumb walls are common on site, and it is far cheaper to allow for scribing or a filler panel in the specification than to negotiate it during installation.

Specify the internal configuration item by item

A one-line instruction such as "shelves inside" invites rework. Break the interior into zones and state each one:

  • Shelved zone — number of shelves, fixed or adjustable, and the clear height you need on the tallest item.
  • Drawer zone — number of drawers, and whether they take cutlery-style trays or deeper storage.
  • Open or display zone — useful for towels and baskets, but it exposes what is stored there.
  • Full-height glazed front — if you want the contents visible, look at Santerson Glass Front Tall Cabinets, and confirm the glass type, glazing method and storage layout for each project.
  • Tall or awkward items — brooms, ironing boards, hampers — with the fixing or restraint required to keep them upright.

Give shelf and drawer positions as dimensions from a fixed datum (the finished floor level), not as an illustrative sketch. If the specification is for more than one unit type across a project, issue a schedule with a unique reference per unit, so substitutions cannot happen silently at the factory or on site.

Name the finish and hardware, and say how they are judged

The collection is offered with project-specific finishes, so state the body material, door material, colour or grain reference, and sheen level. Then close the loop on the parts that get argued about later:

  • Handle style and position, or the handleless detail, including how the door is opened at the top of a tall unit.
  • Hinge type and opening angle, soft closing or not, and which side the doors hang on for every unit reference.
  • Edge treatment and visible edges — where a carcass edge is exposed, say how it must be finished.
  • Integrated lighting, if required: fitting type, switching, and where the driver is accessible for maintenance.

Agree an approval basis before production. A signed sample or approved drawing showing finish, grain direction and handle position gives you something concrete to inspect on delivery; without it, "the colour looks different in this light" becomes a subjective dispute.

Cover the coordination items that decide installation

The last part of the specification is administrative, and it is where most avoidable delays sit. Confirm with your supplier the lead time for the chosen configuration, the packaging and protection method for a bathroom or laundry environment, and the delivery point on site — particularly for upper floors or tight access.

As a furniture and building materials manufacturer working on custom project orders, SANTERSON also lists custom/OEM service, logistics and door-to-door delivery, and installation and after-sales support among its services. Use those stages deliberately: have the specification, drawings and finish approvals confirmed before production starts, keep one document that carries all unit references through to delivery, and record site conditions at handover. For a project ordering several fit-out items together, grouping tall cabinets with related joinery in one enquiry usually reduces conflicting dimensions between trades.

Before you send the enquiry, read the specification back against the product information: dimensions, material, loadings, glass and installation details are listed as items to confirm for each selected configuration. Anything you have not written down is still open — and it will be settled on site instead.

A quick pre-production check

  • Unit reference, position in the room, and quantity are stated for every cabinet.
  • Width, height and depth are given with a datum, and envelope obstacles are listed.
  • Internal zones are dimensioned, not sketched, including clear heights.
  • Finish, edge treatment, hinges and handle details are named and approved on a sample or drawing.
  • Appliance, ventilation and electrical requirements are resolved if any appliance is integrated.
  • Lead time, delivery point, packaging and installation responsibility are confirmed in writing.

Work through those six lines and the enquiry you send will be specific enough to price accurately and to inspect on arrival. That is what a clear specification is for: it removes the conversation you would otherwise have with the site team, holding the schedule while nobody can agree what was ordered.