A wardrobe drawing that looks finished in a presentation deck can still be unbuildable on site. Open modular wardrobes make that gap obvious quickly, because there is no door to hide behind: shelf heights, hanging runs, drawer positions, edge detailing and finish all stay visible from day one.

When an interior designer and a procurement buyer specify open modular wardrobes together, the work that used to cause site surprises moves earlier — into the drawing review, the sample approval and the purchase order.

Why open modular wardrobes expose misalignment early

Modular wardrobe systems are built from repeating units, so a single dimension error repeats across a wall instead of staying local to one cabinet. With an open configuration there is no front frame or door reveal to absorb small deviations either: the carcass edges, the shelf fronts and the way each module meets the wall are all part of the finished look.

In practice this means designers and buyers are usually arguing about the same three things in different vocabulary. The designer is protecting proportion, sightlines and how the storage reads in the room. The buyer is protecting budget, lead time and the number of change orders. Both outcomes depend on one shared document set, agreed before production starts.

The four decisions to close out before any order is placed

1. Layout: what each module is actually for

A layout that only shows hanging and shelving is not a specification. The design team should confirm how the space will be used — long hanging, short double hanging, drawer storage for folded items, open display niches — and the buyer should check that the mix matches what the project budget allows per metre of run. Within the Modular Wardrobes collection there are layouts built around different priorities: shelf focused modular wardrobes where open storage carries most of the load, and drawer focused modular wardrobes where deep drawer units replace shelving below the hanging rail. Where a project needs both, combination modular wardrobes let the mix change along the same wall.

2. Dimensions: who measures, and against which finish line

Made-to-measure wardrobe work fails most often on the reference line, not on the cabinet depth. Agree in writing whether the drawings show structural walls or finished wall faces, where the ceiling and floor finishes land, and which side of the module skirting, architraves and cornices return to. The buyer should then confirm site-verified dimensions after the wet trades and floor finishes are complete, rather than relying on architectural dimensions carried forward from an early drawing issue.

3. Materials and finishes: sample first, then lock the code

Open wardrobes show their material everywhere — carcass interior, shelf edges, drawer fronts, back panels. A finish approved as a photograph will not survive comparison with a physical sample once it is next to the room's flooring and joinery. Both parties should sign off a physical sample and record the exact finish code on the order, so the buyer can place repeat batches for later villas or floors without re-opening the approval.

4. Interfaces: what the wardrobe meets on site

Lighting inside the modules, skirting returns, wall panels and architraves, adjacent built-in cabinetry, and any structural element that cuts across the run all need a named owner in the drawing set. A single coordinated detail sheet covering these interfaces prevents the classic argument about whether the wardrobe supplier or the site contractor fills the gap.

A practical division of responsibility

Decision Designer signs off Buyer confirms
Module layout and internal configuration Storage mix, proportions, sightlines, display niches Cost per run metre, whether the mix can be repeated on other floors
Dimensions Setting-out drawing, reference lines, interface details Site-verified dimensions after finishes, tolerance responsibility
Finish and material Physical sample approval, finish code, interior carcass look Finish availability for repeat orders, packaging protection in transit
Delivery and installation Site readiness, sequence with other fit-out trades Freight mode, delivery address, installation window, snag list
One page that prevents most rework Before production, both parties should be working from the same three items: a dimensioned elevation of every run with finish codes marked, a module schedule listing each unit and its configuration, and a written record of who verifies site dimensions and when. If any of the three is missing, the order is not ready.

How a single supplier reduces the handover risk

Wardrobes rarely sit alone in a project package. They meet wall panelling, doors, flooring, lighting and kitchen or vanity cabinetry, and each of those interfaces is another party to coordinate. Sourcing built-in joinery together with the surrounding finishes from one manufacturer keeps material, finish coding and dimensional responsibility inside one production run instead of spreading it across several vendors.

SANTERSON works as a China-based furniture and building materials manufacturer on villa, hospitality and office projects, with custom and OEM production supported by freight coordination, door-to-door delivery, installation support and after-sales service. For wardrobe packages that means the same team handles the open modular wardrobe carcasses and the adjoining cabinetry and panelling, so interface details are resolved once rather than negotiated between separate suppliers.

Where to start if you are specifying a set now

Send the layout drawings and the room's finish schedule together, and ask for a module schedule back with finish codes and made-to-measure dimensions marked. That single exchange usually reveals within one round whether the designer and buyer are working from the same information — and what still needs closing out before the order is placed.

To scope an open modular wardrobe package for a villa, hotel or apartment project, contact SANTERSON with your drawings and target delivery location.