Wood panel partitions and custom wall panelling look simple on a drawing. A run of matching panels, a flush door, a clean shadow line. That is exactly why the after-sales conversation gets postponed – nothing in the specification looks technically risky. The problems show up later: a panel that no longer sits flat against the wall, a sliding track that binds, a replacement panel that arrives in a slightly different veneer tone, or an installer on site who has no drawing to work from.
If you are sourcing wood panel partitions for a villa, hotel or office fit-out, treat the after-sales terms as part of the product. Below are the details worth putting in writing before production starts, and the questions to ask your supplier for each one.
1. What exactly is covered, and for how long
“Warranty included” tells you very little. Ask for the coverage split by component, because partitions age in parts rather than as a whole unit:
- Panels and finishes – delamination, warping, edge banding lifting, colour or grain deviation on a replacement panel.
- Hardware – tracks, hinges, handles, levelling feet, connectors. These are usually the first items to fail and are frequently warrantied separately from the joinery itself.
- Workmanship at handover – snags recorded during inspection, and who closes them out.
Ask which party is responsible when a fault appears after installation: the supplier alone, or the supplier plus whoever installed the system. Where on-site installation forms part of the package, as it does under our installation and after-sales support, that responsibility is written into one scope rather than argued about later.
2. How a replacement panel gets matched years later
This is the single most useful question to ask, and many buyers never think to ask it. Veneer, lacquer and laminate batches vary. A panel ordered eighteen months after handover can arrive close but not identical.
Put these in the order file:
- The exact finish reference – veneer species, cut, grain direction, lacquer or laminate code, sheen level.
- The production drawings and shop drawings used for the original run, kept by both sides.
- Whether you order spare panels with the original batch. For a long hotel corridor or a repeated guest-room layout, ordering a small reserve at production stage is far cheaper than matching later.
For made-to-measure work this matters more, not less. Each wall panel system is cut to the opening it was measured for, so a replacement is a new manufacturing job, not a shelf pick-up.
3. Hardware supply and spare parts
Sliding and bi-fold partition systems depend on hardware that is easy to damage during fit-out and hard to source if it is a discontinued profile. Ask:
- Are tracks, rollers and guides stocked as spare parts, and for how long?
- Is the hardware a standard profile or a proprietary one? If proprietary, who holds the tooling?
- Can replacement hardware be shipped with the next container, or does it need its own shipment?
Our partition sliding systems and closet sliding panels are configured per project, so track type, hardware set and opening dimensions should be recorded in the order confirmation. If those details are missing from your supplier’s paperwork, request them before production.
4. Who answers, how fast, and through which channel
Response terms only mean something if there is a named channel behind them. Ask for:
- A single contact who handles post-delivery issues, not a general sales inbox.
- The working hours that contact covers, stated in your time zone rather than the factory’s.
- How a claim is raised – photo and order number by email, a form, or a call – and what evidence speeds it up.
Time-zone gap is the practical difficulty in cross-border procurement. Our team works Monday to Saturday, 8:00 AM to 6:00 PM (GMT+8), with enquiries answered within 24 hours; buyers in Australia and the Middle East should plan their site queries around that window rather than expecting same-day answers at their own end of day.
5. Installation guidance when the installer is a third party
Many partitions go wrong on site rather than in the factory – the substrate was not flat, the fixing method was improvised, or the panel sequence was reversed. Ask your supplier what they will actually provide:
- Fixing detail drawings and setting-out dimensions for the local builder.
- Substrate and flatness tolerances the wall must meet before panels arrive.
- Whether remote or on-site guidance is available if the installer hits an unfamiliar detail.
Where the supplier also handles turnkey project delivery, the same team that drew the panels supervises fitting them, which removes the handover gap between designer, factory and local trades.
6. What is excluded – read this before you sign
Every warranty has exclusions. The ones that cause disputes in partition work:
| Common exclusion | Question to ask |
| Damage during on-site works after handover | Who protects installed panels while other trades finish the room? |
| Moisture and substrate movement | For bathroom-adjacent panelling, what wall preparation is required, and does the finish cover wet-area exposure? |
| Normal wear in high-traffic areas | For hotel corridors and guest rooms, what abrasion level was the selected finish specified for? |
| Third-party modification | Can local trades cut or re-drill panels without voiding coverage? |
Where a project combines panelling with integrated doors and paneling, ask whether the door, frame and panel run are covered under one warranty or split across several. Split coverage is where claims stall.
A short list to send your supplier
Before you confirm an order, copy these into an email and ask for written answers:
- Warranty period per component: panels, finish, hardware, workmanship.
- Finish reference codes recorded on the order confirmation.
- Spare panel and spare hardware availability, and how they ship.
- Named after-sales contact, working hours in your time zone, claim procedure.
- Setting-out drawings, fixing details and substrate tolerances for the local builder.
- Exclusions in plain language, especially moisture and site damage.
A supplier who answers these cleanly before production is a supplier who can answer them afterwards. If the answers are vague at quotation stage, that is your warning – the same vagueness will apply when a panel needs replacing on site.
SANTERSON supplies custom partitions and panelling as part of one-stop furniture and building materials procurement, with production drawings, door-to-door delivery and installation support under one scope. Send your drawings and opening dimensions to our team and we will confirm the specification, finish references and after-sales terms in writing before anything goes into production.