A wardrobe that looks perfect on the sample board can still stall a job on site. Usually the problem is not the door panel — it is that nobody wrote down, early enough, what the glossy finish actually has to sit next to. If you are putting Glossy Finish Melamine Wardrobes into a villa or apartment package, the schedule line has to carry more than a product name.
Materials schedules are where procurement decisions become auditable. For built-in joinery, each line needs enough information that a site team, a second trade and your supplier all read the same intent. Below is how we build that line for glossy melamine wardrobes on multi-room projects.
Start with the finish, not the model number
High-gloss surfaces are specified by reflection as much as by colour. Two panels can share a colour code and read completely differently once light hits them at 30 degrees across a bedroom wall. In the schedule, record the finish family — glossy melamine in our case — and then state how the sample was assessed: under which light source, next to which adjacent finishes, and whether the reflection you approved was a small swatch or a full door.
Our glossy finish melamine wardrobe line sits inside a wider melamine wardrobe collection, so the same carcass and layout logic carries across matte finish melamine wardrobes and wood grain melamine wardrobes. That is useful on a whole-project basis: you can run glossy doors in the main bedroom, matte in the second and third bedrooms, and wood grain in the hallway storage while keeping one carcass family, one hardware set and one production batch.
What each schedule line should carry
For built-in wardrobes we ask clients to give us six fields per line. Missing any of them tends to produce a variation order later.
| Schedule field | What it prevents on site |
|---|---|
| Room, wall and datum dimensions | Panels arriving for the wrong opening, or a wardrobe that clashes with a skirting or cornice line |
| Door style and opening method (hinged, sliding, open) | Clearance conflicts with beds, doors and vanities discovered after fixing |
| Finish code plus adjacent finishes | A glossy door approved in isolation that then reads badly against the flooring or wall panel beside it |
| Internal layout (hang, shelf, drawer focus) | Carcass built for the wrong storage mix, which is expensive to change once drilled |
| Edge, handle and hardware notes | Handleless details being cut as if a handle were required, or vice versa |
| Interface trades and their sequence | Wardrobes delivered before flooring, lighting or wall panelling are set out |
Group the wardrobe with the finishes it touches
A built-in wardrobe is a boundary element. It meets flooring on one side, wall finishes behind, ceiling or cornice above, and lighting either inside or in front of it. In the schedule we group wardrobe lines together with the engineered wood flooring, wall panel systems and interior doors for the same room, so one approver signs off the whole junction rather than three people signing three separate documents.
This grouping matters most with glossy surfaces. Reflection repeats whatever is nearby: a change in flooring tone, an untracked reveal line, a switch plate that moved 100 mm. When the flooring and the wardrobe are approved as one set of junctions, those details get resolved before production rather than during installation.
Lock dimensions once, then let fabrication follow
Our wardrobes are made to measure — sizing, layout and finish are specified per project, which is exactly why the schedule should be frozen before shop drawings go out. Re-measuring after wall finishes are complete is the safer sequence for a glossy door run: the panel sizes then account for the finished face of the wall, not the blockwork.
Where a project spans several bedrooms, confirm the dimension set room by room rather than assuming repeats. Identical-looking rooms rarely have identical finished dimensions, and one corrected measurement at schedule stage is cheaper than one re-made door at site stage.
Keeping one supplier across the fit-out
When wardrobes, kitchen cabinetry, doors and panelling come from separate suppliers, each party protects its own tolerance and the junctions become someone else's problem. Coordinating them as one package — as we do for villa and apartment projects through our one-stop solution service — means the same drawing set governs all of it, and interface details are settled in a single review.
If your project needs non-standard sizes, an alternative handle arrangement or a finish outside the standard range, that is a custom and OEM conversation worth having at schedule stage, not after quotation. Freight, packaging and delivery sequencing are then planned against the same release batch through our logistics and door-to-door delivery service.
A short worked example
Take a three-bedroom villa. Main bedroom: glossy melamine sliding doors, full height, with the junction to engineered flooring and the cornice line drawn on the same sheet as the floor laying sequence. Second and third bedrooms: matte melamine hinged doors in the coordinating neutral, hung after the wall finish is complete but before the carpet or flooring in front of them is laid. Hallway: wood grain melamine storage matching the entry joinery. Three finishes, one carcass family, one drawing review, one shipment plan.
Product specifications, finishes and available configurations are confirmed per project at quotation stage; sample swatches should be approved under the site's own lighting before any schedule line is signed off.
Send us your schedule draft
If you have a wardrobe schedule that is not yet production-ready, send the room list and finish intent to SANTERSON. We will mark up what is missing — dimensions, interface notes, hardware details — and return a specification we can actually build to. Enquiries are handled by PHILLIP on +86-13928214007, or through our contact page.