A quotation for a large swim spa arrives, and it usually looks complete: model number, dimensions, a jet count, a price. The problem is that two proposals for the same Outdoor Swim Spa WS-S12 can cover very different equipment, because the specification sheet hides as much as it reveals. Before you sign anything, work through the checks below.

Start with the model designation, not the price line

In a configurable range, one letter in the model code changes the equipment list. In our catalogue the WS-S12 is listed with water jets, LED lighting and ozone, while the WS-S12-T carries the same shell plus a swim training system. Both are catalogued at 11740 × 2200 × 1470 mm, so the footprint tells you nothing about which unit you are buying.

Read the proposal against the published product page and ask one blunt question: does the quoted model include the swim training system or not? If a lap-swimming lane matters to the client, a quote that quietly drops it looks cheaper than a competitor’s until someone tries to swim in it. Equally, if the site is a resort spa pool for soaking and hydrotherapy rather than training, paying for a swim system you will never switch on is waste of another kind.

Reconcile the specification table line by line

The WS-S12 catalogue entry lists a control system (1 set), water pumps (2 pcs), a filter pump (1 pc), a jet total of 73 pcs, LED lighting (1 light plus 50 small LED lights) and total power of 7.65 kW. Treat these numbers as the starting point of a conversation, not the finish.

Specification lineWhat to confirm in writing
Dimensions 11740 × 2200 × 1470 mmWhether these are external shell dimensions or the finished footprint including steps, plant enclosure and any insulation cladding.
Jet total: 73 pcsThe split between hydrotherapy jets, directional jets and air or water-feature devices, and which jets sit in which seating position.
Water pump: 2 pcs / Filter pump: 1 pcPump duty and brand, plus whether the jet pumps are dedicated per zone or shared through one manifold.
Total power: 7.65 kWWhether this covers pumps, controls and lighting only, or also the heat pump and any optional heating listed separately.
Control system: 1 setController type, where it is mounted, and what the client can adjust themselves versus what needs a technician.
LED lighting: 1; 50 small LED lightsFixture locations, whether the fittings are replaceable from outside the shell, and the low-voltage supply arrangement.

Note: the WS-S12 catalogue entry does not list a swim training system for this model; the WS-S12-T variant does. Confirm which configuration is being quoted.

A manufacturer who answers these questions with specific model references is a different kind of supplier from one who answers with “standard configuration”. The written answer is also what your electrician, plumber and site supervisor will work from.

Separate the base unit from the options list

The model code is only the first place a quotation can drift. Catalogue figures for this range are transcribed from product pages, and production evolves; ask the manufacturer to restate each figure inside the quotation, with the specification version they are quoting from, so that what you sign matches what ships.

Optional accessories catalogued for this range include control systems, UV sterilisation, water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model, so a fair comparison requires the same option set on every proposal you receive.

  • Heat pump — ask for the heating capacity and the assumed inlet water and ambient conditions. A heat pump sized for a mild climate behaves very differently in a cold one, and running cost follows from that, not from the kW figure on the spa itself.
  • Insulation — ask what is insulated (shell, base, plant bay, cover), what material and what thickness. On an outdoor spa used across the cooler months, heat loss through the shell and cover is a major part of running cost.
  • Filtration — sand filtration and cartridge filtration have different running routines. Confirm how often the client must backwash or clean, and where the filter sits relative to an access hatch.
  • UV / ozone sanitisation — confirm whether the system is a replacement for or a supplement to chlorine or bromine, since that changes what maintenance chemicals the site keeps on hand.
  • Steps and access — confirm whether steps are included, how they are fixed, and whether they fit inside the quoted footprint.

When two proposals for the same model sit far apart on price, compare their option groups line by line before judging either one. The gap is usually in heating, filtration, insulation or access items rather than in the shell.

Check the electrical and structural interface early

With total power listed at 7.65 kW, plus any heat pump quoted as an option, the electrical supply is where projects most often lose time. Ask the manufacturer for the connection requirement of the quoted configuration: supply voltage and phase, dedicated circuit sizing, protective device and residual-current arrangement, and where the isolator should sit relative to the spa. Confirm this against your local wiring rules with your own electrical designer; a supplier’s export specification is an input to that design, not a substitute for it.

On the structural side, a 11.7 m long vessel holds a very large volume of water when full, and the load path changes once people are in it. Get the filled weight and the support arrangement stated, then have your engineer confirm the slab, plinth or deck before the spa arrives. If the unit is being set into a terrace or on a podium, ask how drainage from the plant bay is handled.

Judge the supplier on process, not promises

A swim spa is rarely bought alone on a project. On villa and hospitality work it sits in the same package as outdoor furniture, pergolas, loungers, poolside lighting and the surrounding paving or cladding. Coordinating that scope through one supplier shortens the coordination chain you have to manage between vendors.

SANTERSON works as a one-stop furniture and building materials supplier, taking projects from design consultation through material selection, manufacturing, project management and site coordination. Where a client needs a different shell size, finish or equipment mix, the Custom & OEM Service covers bespoke specification and prototyping rather than forcing you into a catalogue variant. For freight, the Logistics & Door-to-Door Delivery service handles sea, air and rail forwarding, packaging and container loading, customs paperwork and shipment tracking — ask specifically how a spa shell is crated, which container it goes into, and what the delivery point actually is.

Then read the after-sales terms as carefully as the equipment list. The Installation & After-sales Support service covers on-site installation, inspection and snag lists, warranty coverage, spare parts and ongoing maintenance. For a swim spa, three details decide whether that support is real in practice: which components are covered and for how long, how pumps, controllers and jet motors are replaced once the unit is commissioned, and who attends site when something fails in the first season.

Run the comparison before you respond

Take every proposal you receive and rebuild it into one common format: model code and confirmed feature set; specification lines as quoted, not as catalogued; options included and excluded; electrical and structural requirements; filled weight and support method; freight terms and delivery point; warranty scope and spare-parts route. The proposals will stop looking comparable at exactly the points where you should be asking questions.

If you are specifying an Outdoor Swim Spa WS-S12 for a villa, resort or private estate, send us the model code and the site conditions and we will confirm the equipment list, options and delivery arrangement for that configuration before you commit to a number.