A glass-front bar cabinet is one of the few built-in items in a project where the most expensive and most fragile element is a door panel that has to survive packing, lifting, ocean or road freight, unloading and finally installation. Santerson Glass Front Bar Cabinets are made to order for residential living projects, with dimensions, materials and finishes specified per site. That means there is no standard carton sitting on a shelf waiting for your order. Before you release production, here is what to put in writing about how those cabinets travel.

Why glass-front units need their own packaging plan

In a made-to-measure programme the cabinet carcass and the glazed door fronts usually leave the factory at different moments and in different conditions. Carcasses are boxy, relatively rigid and can be stacked with care. Glass doors cannot be stacked, cannot take point loads, and cannot tolerate the twisting that happens when a bundle shifts inside a container. Confirming this split early, with carcass packaging kept separate from door-front packaging, prevents the common project problem of everything arriving in one crate, the glazing riding against the cabinet sides.

What to confirm about the glazed door fronts

  • Glazing type and thickness. The product page lists configurable materials and finishes, but it does not state a fixed glass specification. Ask for the glazing actually quoted for your units: thickness, tempered or annealed, clear or tinted. Then make sure the packing method matches it.
  • Vertical transport. Glass panels travel upright, on edge, in A-frames or racking with cushioning between each panel. Ask explicitly whether the door fronts will ship vertically, and how they will be restrained so they cannot lean during handling.
  • Edge and corner protection. Damage to a glass edge often shows up later as a crack under load rather than at delivery. Confirm edge protection on every panel, not just the outermost ones in a bundle.
  • Hardware shipped loose or fitted. Hinges, handles, stays and light fittings for glazed doors are commonly packed separately and fitted on site. Ask which items travel assembled and which travel loose, and confirm each set is labelled against its own door front.

What to confirm about the carcasses

  • Assembled or flat-packed. Both approaches are workable. Assembled boxes reduce site labour but take up more volume; flat-packed units fit more into a container and pass through tighter lifts and doorways, at the cost of assembly time. Ask which option is quoted, because it changes freight cost as well as installation effort.
  • Panel protection between units. Where cabinets are nested or stacked, confirm protective interleaving so finishes such as lacquer, acrylic, veneer, melamine and aluminium frames do not rub or mark in transit.
  • Crate and carton specification. Ask for the packing list in advance: box dimensions, gross and net weight per package, total volume, and whether timber crates or reinforced cartons are used. Weight per package matters if the site has a service lift or manual-handling limits.
  • Moisture protection. Sea freight moves through temperature swings that draw condensation inside a container. Confirm internal wrapping and, where timber crates are used, that the timber is treated and suitable for international shipment.

Loading, documents and site readiness

Santerson's logistics service covers freight forwarding by sea, air and rail, customs paperwork, packaging and container loading, shipment tracking and door-to-door delivery. Those are the exact points where packaging questions have to be settled, because once a container is stuffed there is very little you can change.

Point to confirmWhy it matters on site
Container type and how the glazing is racked inside itDetermines whether door fronts can be lifted out upright at the destination without being handled twice.
Marking on each package: project code, room or unit number, crate sequenceLets the site team route crates to the right apartment or floor instead of opening everything in one pile.
Packing list matched to the shop drawingsMade-to-measure units are identified by drawing reference, not by a catalogue code. A mismatch here is where "wrong size" claims begin.
Unloading method and equipment at the destinationCrates holding glass need the right forklift, trolley or handling crew on the day, so this must be arranged before the truck arrives.
Storage area available between delivery and installationGlazed panels need a dry, level place to stand upright until the fitter needs them.

Insurance is worth settling at the same time. The logistics service refers to cargo insurance options and dedicated logistics coordinators. Confirm in writing which party insures the glazing, and what evidence you must produce if a panel arrives cracked: photographs, signed delivery notes, and damage marked on the waybill at the time.

Inspection at handover

  • Check every glass-front door front for edge chips before crates leave the site, and photograph the packing as you found it.
  • Open a sample of carcass boxes against the packing list to confirm finish and orientation before installation crews start work.
  • Record any damage on the delivery paperwork at the moment of handover, not afterwards.
  • Keep loose-hardware labelling intact until each door is hung. Re-matching unlabelled fittings to made-to-measure doors costs more time than the damage itself.

Santerson's installation and after-sales service covers on-site installation, inspection and snags, spare parts and replacement. If a glazed panel does need replacing, the practical question is how quickly a single made-to-measure door front can be re-produced and shipped, so ask that before you order rather than after the damage.

Related products worth reviewing together

Bar cabinets rarely sit alone in a drawing set. The Santerson Glass Front Bar Cabinets collection is specified alongside other glazed and built-in items, and it is usually more efficient to agree one packaging standard across the whole joinery package than to negotiate crate by crate. Buyers comparing layouts often review Santerson Compact Bar Cabinets for smaller living spaces and Tall Bar Cabinets where the bar is built into a full-height wall. Where the project also carries kitchen joinery, the Kitchen Cabinets and Hotel Appliances range lets you place cabinetry and matching glazed units with one supplier, on one delivery schedule.

Because these cabinets are made to measure, the packaging detail follows the specification you sign off. Settle dimensions, materials, finishes and hardware first, then confirm the packing method in writing before production starts. That order of work is what keeps fragile glazing out of project disputes.

To confirm glazing specification, crate type and container loading for a bar cabinet package on your project, send the drawings to SANTERSON and request a packing plan with the quotation. Contact: PHILLIP, +86-13928214007 (phone / WhatsApp), santerson@qq.com. Full enquiry details are on the contact page.