A wood grain pvc cabinet order rarely fails at the factory. It fails on site: a run that no longer fits because a floor finish was built up, a door that fouls a newly laid tile bed, an appliance niche measured before the appliance was chosen. An installation plan is the document that removes those surprises before the containers are loaded. Below is the checklist we work to on residential kitchen projects, and on villa and apartment fit-outs where cabinetry has to arrive ready to fix, hang and hand over.

1. A measured drawing set, not a sales sketch

The plan starts with dimensions taken on site and signed off by the person doing the fitting. For each wall run record the finished floor level, the finished wall face, and the position of every door opening, window reveal, switch, socket, riser and flue. Note out-of-plumb walls and uneven ceilings explicitly, because matte pvc cabinets and their worktops are manufactured to the numbers you send; scribing on site is a contingency, not a method.

Deliverables we expect in the set: elevations of every run with base-unit heights and plinth details; a reflected ceiling plan showing where wall units meet lights, hobs and extractor ducting; a services drawing for water, waste, gas and power relative to unit carcases; and a schedule that lists each unit by reference so the site team can match a crate label to a drawing without guessing.

2. Material and finish confirmation before production

PVC-wrapped panels are specified as a system, not a colour name. The plan should state the substrate, the wrap or foil, the edge treatment, the handle or handleless profile, and the hardware brand and load rating. Wood-grain effects vary noticeably between finishes: a High Gloss PVC Cabinets surface reflects light along the grain and shows every misalignment in the run, while a matte or textured surface hides it. That difference changes how flat your walls need to be and how the units are lined up, so decide the sheen before you set out the site tolerances.

Approve physical samples, not screen images: one door in the selected grain and sheen, one edge sample, one drawer front with its handle detail. Keep the signed sample on site with the drawing set. Where a project mixes finishes — for example a wood-grain run against a Santerson Glass Front Pvc Cabinet display section — show the transition detail in the plan, including trims, end panels and how the glass frame meets the adjacent carcass.

3. Appliance, worktop and stone interface

Every built-in appliance belongs in the plan with its model or at least its confirmed cut-out dimensions: oven, hob, extractor, dishwasher, fridge, wine cooler, microwave. The niche is built to the appliance, so an unconfirmed appliance is an open risk on the drawing. Record hob thickness and the clearance the extractor needs, then show the duct route — including where it crosses ceilings, beams or bracing that the site team must allow for.

Worktops need their own line in the plan: material, thickness, edge profile, splashback return, sink cut-out position and tap hole, hob cut-out, and the joint detail at any run change. Stone is measured after the base run is fixed and levelled, so sequence it in the programme rather than assuming it arrives with the cabinets.

4. Site conditions, storage and the order of works

Cabinetry should be one of the last trades in. The plan states what must be complete before delivery: wet trades finished and dried, floor coverings laid, painting undercoated, plaster cured, services first fix tested and signed off, and site cleaned. Give a dry, covered storage area with pallet access, and state that crates stay closed and upright until each run is started.

Fixing substrate matters as much as the units. Where walls are stud, plasterboard or lightweight block, the plan records the batten or nogging design and who installs it — the site contractor or us — with positions marked on the elevations. Wall units loaded with heavy contents need continuous noggings at the correct height; that detail has to be drawn before the walls are closed up.

5. Delivery, unpacking and acceptance

For imported consignments the plan carries the container or crate list cross-referenced to unit references on the drawings, plus the delivery window, lifting route and access constraints such as lifts, stair widths or gated sites. Check each crate against the list on arrival, photograph any damage on the packaging before it is removed, and note shortages the same day while the claim window is open.

Unpack one run at a time, dry-fit the carcasses, adjust legs to the floor line, then check levels across the whole run before doors go on. Doors and drawers are set last so that alignment can be corrected after the building has moved or settled.

6. Snag list and handover

Close out with a written snag list: door and drawer alignment, soft-close operation, handle and hinge function, seals at worktop junctions, cut-outs for sinks and hobs, visible fixings, and any site-trimmed edges. Photograph the completed runs, keep the hardware spares and finish codes in the handover pack, and record which supplier to contact for replacement panels or hinges. A handover pack that names the exact finish and hardware makes future repairs straightforward instead of a matching exercise.

How we support the plan

Our cabinetry is made to measure for each project, with material and finish options and layouts drawn to the space — from Santerson Shaker Style PVC Cabinets to integrated tall-unit runs. Dimensions and selected specifications are confirmed for each order before production, so the drawing set above is the document we work from rather than a suggestion.

Because kitchens are only one part of a fit-out, the same coordination applies across Custom Built-in Kitchen Cabinets - Interior Fixtures for Hotel & Apartment Projects, wardrobes and joinery in one package. Our Custom & OEM Service covers bespoke finishes and prototyping; Logistics & Door-to-Door Delivery handles freight, packaging and container loading to site; and Installation & After-sales Support covers on-site fitting, inspection and spare parts. Send us the measured drawings and appliance schedule and we will return a quotation with the unit references already matched to your elevations.

Talk to our project team about cabinetry for your next villa, apartment or hospitality fit-out — Phone / WhatsApp: +86-13928214007 (PHILLIP), Email: santerson@qq.com.