A made-to-measure wall system is ordered long before anyone can see the finished panels standing in the room. For Santerson Partition Sliding Systems, finish, layout and dimensions are all specified project by project, which means the sample you approve is the closest thing to a preview of production you will get. Reviewing it carefully takes an afternoon. Skipping that step can cost you a re-run of panels, a delayed handover and an argument about what was agreed.

This guide walks through what to check on a finish sample for a partition sliding system, how to record the result so the factory and your site team read it the same way, and where sample review fits in the sequence before production begins.

What A Finish Sample Actually Covers On A Partition Sliding System

Partition sliding panels are not a single fixed item. The same layout can be built with different panel faces, different edge treatments and different hardware, and the sample is where those choices stop being words on a drawing. The product listing states made-to-measure sizing, material and finish options and a layout tailored to the project; the sample turns each of those into something you can hold.

Before a sample is requested, it helps to know which part of the system you are actually approving:

  • Panel face — the visible surface: wood veneer, lacquer, laminate, textured panel or glass. This drives the look of the wall when the panels are closed.
  • Edges and reveals — how panel edges are finished and how much shadow gap sits between panels. Small changes here change whether a closed run reads as one surface or as separate doors.
  • Track and hardware — the running gear, handles or handleless profiles, and the opening geometry. These are confirmed per project rather than assumed from a catalogue picture.
  • Adjacent finishes — the wall paneling

If your scheme also includes a full-height storage wall, ask for the sample in the same panel build you intend to order. A face that works on a closet front does not always behave the same way on a tall partition run, and other panels in the sliding panel systems range are configured separately, so each one needs its own sign-off.

Request The Sample With A Written Reference Point

Samples go wrong when the request is vague. Send the same information you would send with a purchase order, so the sample arrives as a test of your specification and not of someone's guess:

  • The room or zone the panels sit in, plus the finish schedule reference from your drawings.
  • Panel face material and finish, edge detail, and whether the surface is matte, satin or high gloss.
  • Any grain direction, joint pattern or texture orientation that matters to the design intent.
  • The opening arrangement you are considering, so hardware can be matched to panel weight and size later.

Where a project needs something outside standard options, this is also the point at which bespoke finishes and textures can be discussed under the custom and OEM service, before any tooling or production commitment is made.

The Eight Checks To Run On The Sample

Work through these in one sitting and write the answers down. Photograph each check as you go.

  1. Colour under your own light. Check the sample in daylight, in the room's main artificial light and in low light. A veneer or lacquer that reads warm by a window can pull grey or green under cool LED panels.
  2. Texture and direction. Run your hand across the surface and note grain direction, sheen variation and whether texture is visible at viewing distance rather than only up close.
  3. Edges and corners. Look for consistent wrapping, clean mitres and no telegraphing of the substrate. This is where poor workmanship shows first on a moving panel.
  4. Scale. A small swatch flatters a busy grain or a strong texture. Ask for a panel-sized piece, or view the swatch from three metres before approving.
  5. Comparison against adjacent materials. Hold the sample next to your flooring, skirting and fixed joinery. Matching is judged side by side, never in isolation.
  6. Marks and recovery. Press a fingernail lightly, then wipe the surface with the cleaning method you intend to use on site. Note whether marks lift or stay.
  7. Hardware feel. If the sample includes a track or handle section, operate it as a door would be used — full travel, both directions, and stop at the reveal.
  8. Consistency across pieces. If you received more than one piece, compare them side by side. Variation between two samples of the same finish tells you what to expect across a batch.

Record The Approval So It Survives The Project

An approval that lives only in an email thread is not an approval. Sign off the sample with a short record attached:

  • Sample reference number, project name and date received.
  • The exact finish description as specified — material, colour or decor reference, sheen level, edge detail.
  • Named approver and the date of approval, plus any conditions attached to it.
  • Photographs of the sample against the adjacent finishes, taken in the actual room.
  • One retained physical sample held on your side, with the factory keeping a matching reference.

Anything you reject should come back with a reason and a replacement request, not just "not this one". If the colour is close but the sheen is wrong, say so — that keeps the next iteration short instead of starting the conversation again.

Where Sample Review Fits Before Production

Sample sign-off sits between detail confirmation and the start of production. Only after dimensions, hardware and finish are all confirmed should made-to-measure panels be released to the floor, because a partition run is cut to the opening it belongs to and cannot easily be re-used elsewhere.

For projects that combine sliding partitions with other built-in work — niche paneling, media walls or cabinetry — review the samples together in one visit. The rooms are read as a whole, and approving each finish separately is how tonal mismatches get through.

Common Reasons Samples Get Rejected

  • Approved under the wrong light. The most frequent cause, and the easiest to avoid by checking on site.
  • Judging a small swatch at full-wall scale. Grain, texture and pattern all read stronger across a large surface.
  • No record of sheen level. Colour matches, but matte becomes satin and the wall reflects differently once installed.
  • Hardware approved separately from panel weight. Running gear that suits a closet front may not suit a taller partition panel.

Before You Sign The Sample Off

Three questions settle it. Can you describe the approved finish in one line that the factory would recognise? Do you have a retained physical sample on your side? And does the sign-off record carry the project name, the date and the conditions? If all three are yes, the specification is ready to move into production.

As a one-stop project furnishing supplier, SANTERSON supplies partition sliding systems alongside the joinery, wall paneling and loose furniture they sit next to, so sample review can be coordinated across the package rather than item by item. Send the drawings and finish schedule for your villa or hospitality project and we will confirm dimensions, track and hardware and the finish options before anything is released to production.