A kitchen cabinet line that only appears once in a brief tends to cause trouble later. "Solid color acrylic, gloss white" means very little to a factory until someone has written down which panel the colour sits on, how the edges are handled, what the hardware carries and where the units will actually stand. If you are specifying Solid Color Acrylic Cabinets for a villa apartment or a residential scheme, the procurement brief is the cheapest place to settle those questions before production starts.

What the brief has to decide first: where the cabinets are going

Acrylic-fronted cabinetry in our built-in furniture range is specified for residential kitchen projects. That starting point matters, because a gloss or low-sheen front behaves differently in a family kitchen used three times a day than it does in a display wall in a show apartment. Before anyone talks about colour codes, the brief should state:

  • the room and how heavily it is used — main kitchen, secondary kitchen, laundry, pantry or living-area joinery;
  • what sits next to the fronts: worktop and splashback material, built-in ovens, dishwashers, bins and pull-out trays;
  • the light conditions — strong daylight from a window wall shows up surface marks on high-gloss fronts far more readily than side-lit task lighting does;
  • who maintains the units after handover, and whether the owner expects to wipe fingerprints off daily or would rather not see them at all.

Write those four points down and the finish decision usually makes itself. A busy household kitchen generally reads better in a low-sheen front; a display run or a rental scheme where appearance carries the sale is where a reflective front earns its keep.

Choosing the sheen level, not just the colour

"Solid color" describes the decoration, not the surface. The same flat colour can be presented at very different reflectance, and our acrylic family covers both ends of that range. Two entries in the catalogue are worth putting side by side when you are deciding:

  • High Gloss Acrylic Cabinets — a reflective front that mirrors its surroundings, sharpens the look of a handleless slab run and makes a compact kitchen feel deeper. It also records every smear and edge chip.
  • Matte Acrylic Cabinets — the same solid colour with a soft, non-reflective surface that hides handling marks and reads as a flat plane under artificial light.

In the brief, name the sheen level explicitly for each zone rather than once for the whole job. A common pattern we build is high gloss on tall units and pantry runs where marks are less visible, with a matte front on the sink run and prep area where hands are always in contact. Where you want one colour carried through both, say so and ask for samples of both surfaces in that colour — the same pigment can look noticeably lighter or darker depending on reflectance.

Layout, sizing and tolerances

These units are made to measure, with the layout tailored to the project rather than chosen from a fixed set of widths. That removes the usual compromise of filling a gap with a filler panel, but it puts the responsibility for accurate dimensions on the buyer's side of the fence. The brief should therefore record:

  • dimensioned drawings with finished wall and floor levels marked, including where tiling or flooring will be laid;
  • the run lengths at both high and low level, plus ceiling height if tall units go to the soffit;
  • appliance schedules with model numbers and cut-out dimensions, sent with the drawings rather than after order confirmation;
  • which corners are L-shaped or U-shaped runs, and how corner access should work — carousel, pull-out or plain shelf.

Ask for a shop drawing back before production and check it against the site survey. On-site deviations in older buildings are normal; catching them on paper costs nothing, catching them at installation costs a re-made carcase.

Hardware, interiors and the parts people forget

The front is what the client photographs; the interior is what they complain about. Specify these separately in the brief:

  • opening method — handleless slab profile, integrated handle or surface handle — and whether it applies to every door or only to the base run;
  • hinge and slide quality, soft closing as standard, and load ratings for drawers that will carry plates and pans;
  • drawer configuration: deep pots drawers at the bottom, cutlery organization above, tall units with pull-out larder trays rather than fixed shelves;
  • carcase and shelf colours, edge thickness and whether the interior should match the front or contrast with it;
  • integrated lighting for glass-front display sections and task lighting under wall units, including where transformers sit and how they are reached.

If part of the run is meant to display crockery rather than hide it, say which sections — Two Tone Acrylic Cabinets and glass-front combinations are how we usually handle a wall that needs both storage and display.

What to ask the supplier for before you place the order

A short list, all of it obtainable from a manufacturer who works on project volumes:

  1. Physical samples of the exact front in the selected colour and sheen, large enough to judge under your own lighting.
  2. A quotation broken down by room or unit group, so substitutions are visible rather than buried in a lump sum.
  3. Confirmation of what is included in the price: carcase, doors, hardware, plinths, scribes and delivered packaging.
  4. A named contact for production coordination, plus shipping terms and packing method for the container you are consolidating.
  5. The snag and replacement route for transit damage or a mis-made unit — who pays, and how fast the replacement is produced.

SANTERSON has manufactured furniture and building materials in China since 2008, and cabinetry like this is built to the drawings you send rather than to a showroom standard. Because we also handle custom and OEM work, an unusual colour or a non-standard depth is normally a conversation rather than a refusal — but it needs to be in the brief at the start, not raised after cutting.

Common specification mistakes worth avoiding

Three patterns cause most of the rework we see on residential cabinet packages. First, the brief names a colour but no sheen level, and the delivered fronts reflect more light than the render showed. Second, hardware is left "to supplier's standard", which usually means the cheapest slide that fits. Third, tall units are ordered without checking the ceiling height and floor level at both ends of the run, so scribing becomes a site job.

None of those are difficult to prevent. They are all settled by writing down what you actually want in the brief, asking for confirmation back, and keeping one named person responsible for approvals from drawing stage through to handover.

Next step

Send us your drawings, appliance schedule and finish shortlist, and we will return shop drawings and a quotation broken down by zone. Tell us the room, the usage and who maintains the kitchen afterwards — that context is what turns a cabinet line in a brief into fronts that still look right two years after handover.