A metal-frame modular wall system looks simple on a drawing: uprights, shelves, a few lit niches, some closed units. The quotation that lands in your inbox is another matter. Two proposals for what appears to be the same Santerson Metal Frame Modular Systems installation can differ substantially in scope, and the gap between them usually shows up on site rather than on paper. Here is what a serious manufacturer’s proposal should contain for this product family, and which omissions to challenge before you sign.

Start With What You Are Actually Buying

Metal-frame modular systems in this category are configurable built-in shelving for residential wall projects. The product listing describes them as made-to-measure, with finish, layout and dimensions specified to suit each space. That one line carries most of the procurement risk: nothing about a modular system is standard until it has been specified. Shelf spans, frame profile, infill materials, hardware and any integrated lighting are variables, and each one moves price.

The same applies across the wider shelving range. Santerson Floor to Ceiling Systems sits in the same modular shelving collection and is described as project-tailored rather than catalogue-sized. If a proposal treats either product as an off-the-shelf item with fixed dimensions, that is your first warning sign.

Six Items That Belong in the Proposal

Compare scope before price. A proposal that leaves one of these out is not cheaper; it is incomplete.

ItemWhat a complete answer looks like
Dimensioned drawingsRoom-by-room elevations with overall height, width and depth, shelf positions and clear openings. A perspective render is decoration; the dimensioned elevation is what you can hold someone to.
Frame and panel specificationFrame material and profile, surface treatment, board substrate and surfacing (melamine, lacquer, veneer or acrylic), and edge treatment. Named options, not “as per sample” on its own.
Hardware scheduleUprights, brackets, fixings, hinges, slides and any door systems, listed by item with quantities. Hardware is where quiet substitutions happen between quotation and delivery.
Shelf span and loading notesThe product listing itself asks buyers to confirm intended loading for each project. Ask what span each shelf width supports, and what deflection limit applies at the chosen board thickness.
Electrical scope, if lighting is includedCable routes, driver locations, access points, switching, and whether the run is low-voltage or line-voltage, all shown on the drawing. If it is not drawn, it will not be installed.
Finish samples and approval recordPhysical samples carrying a reference code for each finish, plus a signed approval sheet. Screens misrepresent veneer tone and metallic lacquer too reliably to accept a digital choice.

Put these six headings into your request for quotation before you send it out. Suppliers respond very differently when the same checklist is in front of all of them.

Read the Exclusions Before the Totals

The figure worth arguing about is rarely the headline total. It is what sits outside it. For made-to-measure systems, usual exclusions are wall preparation and packing out uneven substrates, floor levels that shift after measurement, site protection, and the trades that connect shelving to lighting and power.

Ask three questions in writing:

  • Who measures on site, and when — before or after plastering and flooring are complete?
  • What happens to the price if as-built dimensions differ from the drawings supplied?
  • Who coordinates with electricians and other trades at handover?

A supplier who answers with a defined process is carrying the risk. A supplier who replies “we will quote that later” has handed it to you.

Judge the Manufacturer by Process, Not Promise

Where shelving, joinery and other fit-out items come from a single source, coordination is the real cost. SANTERSON presents itself as a China-based furniture and building materials manufacturer working on a one-stop basis for villa, hospitality and office projects, covering design consultation and space planning through production, door-to-door delivery, installation and after-sales support. Those stages are published as services, so there is no reason a proposal should be vague about them.

For this product family in particular, ask how new configurations are prototyped or sampled, what minimum order quantities apply to bespoke finishes, and who supervises installation in your country. Custom & OEM service and installation and after-sales support are both named services, so request the specifics instead of accepting a general assurance.

One caution on claims. Company figures quoted in marketing pages — factory area, export share, response times, warranty terms — are not always consistent across a site, and none of them is a project commitment. If a figure affects your decision, get it in writing for your specific scope, and confirm any compliance requirements with your own specifier or certifier rather than relying on supplier statements.

Compare Like For Like

Set the proposals side by side against the six scope items and the three exclusions questions. A lower price nearly always traces back to thinner drawings, unnamed hardware or an unpriced electrical scope, and all three return later as variations. The proposal that costs a little more but states span and loading, names its hardware and shows the lighting on the drawing is usually the one that arrives complete.

If you are sourcing modular shelving alongside wardrobes, kitchen cabinetry, wall panelling or flooring, ask for one combined specification package. A single coordinated set of drawings across those trades catches the clashes that separate product quotations never do.

Send your room drawings, target finishes and intended loading, and request a dimensioned proposal measured against the checklist above. Enquiry details are on the SANTERSON contact page.