A swim spa arrives on a container, gets craned onto a slab, and then has to work with Australian power, an Australian climate and an Australian electrician. The unit itself is only half of the purchase. Before confirming Outdoor Swim Spa WS-S38 for a villa terrace, resort deck or private courtyard project, we suggest you work through the checks below with your supplier in writing — the same way we would want you to check us.
1. Start from the site, not the catalogue
WS-S38 is listed at 3760 × 2080 × 1110 mm. Treat that as a shipping and planning dimension to be confirmed against your access route: gate width, turning radius, crane or forklift pickup point, and the finished slab size with room for steps and maintenance access. Depth of 1110 mm also decides seat height, entry step and how the coping or deck edge is detailed.
Ask two practical questions early: where will the unit be lifted from, and where will water, drainage and any overflow run to? Those answers change the civil works, so they belong in the quotation stage rather than on site.
2. Confirm what is included in your configuration
The published specification sheet for this model shows 51 jets with 6 water columns, 3 water pumps and 1 filter pump, 4 LED lights plus 12 small LEDs, one control system, and a total power figure of 14.05 kW. Features shown are water jets, LED lighting, ozone and a waterfall.
Those numbers describe the catalogue configuration. Options listed for this range — heat pump, UV sterilisation, sand filtration, extra insulation, steps and upgraded control systems — change both the equipment list and the power draw. Request a signed configuration sheet that names every item included in your order, plus what is excluded and supplied locally.
3. Electrical supply: the check most often left too late
A total connected load around 14 kW is not a plug-and-play figure. Before production starts, confirm with your electrician and distributor:
- the supply available at the meter — single or three phase, and the headroom left after existing loads;
- the required circuit size, protective device and RCD/residual-current arrangement for a fixed spa installation;
- cable route, run length and any isolation transformer or equipotential bonding your installation requires;
- whether the heat pump is included in that 14.05 kW figure or sits on its own circuit.
Send the wiring diagram and equipment list to your electrician before production, not after delivery. If the supply needs upgrading, that work should be priced into the project while there is still open ground to trench in.
4. Heating, insulation and running cost by state
A Melbourne winter, a Perth summer and a Queensland wet season place very different demands on the same shell. Ask what insulation is specified for the shell and cover, whether a heat pump is included or optional, and what the recommended standby set-up is for periods when the spa is not in use. If you want an estimate of running cost, ask for the equipment list and duty cycle assumptions behind it rather than accepting a single headline number.
5. Site works and installation scope
Agree in writing who handles each step: the concrete slab and its curing time, the crane or rigging, waterproofing and deck finish, the electrical rough-in, commissioning and handover. Our own service covers on-site installation support, inspection and snag lists, spare parts and maintenance guidance, but the local civil and electrical work is normally carried out by your contractors — so it helps to say so plainly in the order.
6. Freight, customs and delivery terms
We arrange sea, air and rail freight with customs paperwork, packing lists, certificates of origin and door-to-door delivery. For an Australian project, ask us to quote the specific Incoterms for your site, along with transit time, insurance cover and who handles clearance at the port of entry. Confirm the delivery address is reachable by the vehicle that will actually turn up, and whether unloading equipment is included.
7. After-sales: what you can get, and how fast
Before ordering, ask which parts are held as spares and how they reach Australia — pumps, control boards, jets, LED modules and ozone components are the usual suspects. Get the warranty scope in writing: what is covered, for how long, what labour is included, and what is excluded if a third party installs or modifies the unit.
If WS-S38 does not suit your site
The same configurable range covers other footprints and layouts. A long outdoor swim spa with hydrotherapy and relaxation pool suits sites where a genuine lap channel matters, while a customizable shape outdoor spa in square, round, oval or curved formats fits awkward terraces and courtyard corners. Browse the full Swimming Pools and Swim Spas category to shortlist before you commit to a slab.
A short checklist before you sign
- Confirmed dimensions, access route and lifting plan for your site;
- Signed configuration sheet — jets, pumps, lighting, ozone, waterfall, heat pump, insulation, steps;
- Electrical diagram reviewed by your electrician, with supply upgrades priced in;
- Split of responsibilities for slab, waterproofing, electrical and installation;
- Freight terms, insurance and clearance responsibilities stated in the quotation;
- Warranty scope and spare-parts supply route documented.
Send us your site drawing and the electrical supply details, and we will confirm which configuration of WS-S38 fits — with the equipment list, power requirement and delivery terms set out before production begins. As a China-based manufacturer of furniture and building materials working on villa and hospitality projects, including furniture sourcing for Australian projects, we handle design coordination, production, freight and installation support as one package.