Guest-room living areas, suites and hotel lounge zones are judged on two things at once: how put-together the joinery looks, and how well it survives daily housekeeping use. A media wall that photographs beautifully but cannot hold a safe, serviceable television position with clean cable routing becomes a snag list item before handover. This guide walks through how we configure Santerson Glass Front Media Units for hospitality fit-outs, what to specify at enquiry stage, and where the practical decisions actually get made.

Why glass fronts change the specification conversation

A glass-front media unit is not simply a cabinet with a glazed door swapped in. The glazing changes what the unit reads as in the room, and it changes what has to be confirmed before production. Glass frontages are specified per opening, so check which treatment each section carries: lighter glass opens the wall up and reflects light, while tinted glass softens shelving contents into a plane rather than a display.

Because our media units are made-to-measure rather than catalogue-fixed, finish, layout and dimensions are set per project. That flexibility is the point of specifying them — but it also means the buyer has to bring real information to the enquiry: room dimensions, screen size and mounting method, and how much of the storage should be visible versus concealed.

Step 1: Fix the television position before the cabinet layout

Work from the screen outward, not the other way round. Before any elevation is drawn, confirm for each room type:

  • Screen size and whether the set is wall-supported or sits on a unit shelf — these need different substrate and load decisions.
  • Viewing distance from the bed or seating position, which drives the screen centre height.
  • Where power, aerial and network points land, and whether they sit behind the unit or in a service niche.
  • How housekeeping accesses connections for cleaning and replacement, since a fully sealed back panel creates a maintenance problem later.

For suites and lounge areas where the wall also carries display shelving, our Santerson Integrated LED Media Units are often the better starting point, because the lighting and the cabinet carcass are designed together rather than retrofitted. Confirm the lighting and electrical detail for whichever design you select — integrated lighting needs its driver location and switching decided at drawing stage.

Step 2: Decide how much storage is on display

Glass frontage shows what is behind it. In a guest room that is usually a minibar, glassware or a decorative object; in a lounge it may be books and magazines. Two habits are worth designing around:

  • Mix frontages within one composition. Glass-front sections for display, closed doors for spare linen, cables and equipment nobody wants photographed.
  • Set shelf heights to the actual items, not to a standard grid. Glassware needs different clearances from a games console.

Where a project wants a more open feel, our Santerson Open & Closed Combo Units do the same job without glazing at all. Where the whole wall is being resolved as one system, Santerson Full Height Media Walls carry the media zone, storage and panelling in a single run.

Step 3: Specify finishes against the joinery package, not in isolation

A media unit that looks right on its own but clashes with the wardrobe, door and minibar joinery is a wasted sample round. Specify the glass frontage together with the rest of the built-in package so the carcass, doors, frames and profiles share one finish schedule.

ElementWhat to confirm at enquiry
Glass typeThe glazing specified for each opening, and whether frontages are mixed within one composition.
Frame and hardwareDoor style, frame profile, hinge and handle selection, and their finish against the room's metalwork.
Carcass and interiorShelf count and heights, back-panel treatment, and provision for equipment ventilation.
DimensionsSet-out against finished wall lines and floor levels, not structural dimensions taken off drawing alone.
LightingWhether interior lighting is included, where drivers sit, and how circuits are switched.

For rooms where the wall needs a wider composition than a single unit — a full lounge elevation with display niches — Santerson Wall Mounted Media Walls are configured to the same project dimensions and finish schedule.

Step 4: Put the site conditions in writing before production starts

Product pages for these units list finish, layout and dimensions as project-specific rather than publishing one fixed specification, because each unit is built to a project brief. That means the following are confirmed per project rather than assumed from the catalogue:

  • Final dimensions against finished floor and wall lines.
  • Glass specification and safety requirements for the location and use.
  • Hardware grade and cycle expectation for hospitality traffic.
  • Mounting method and substrate fixings for wall-mounted compositions.
Practical rule: do not let a media unit go into production on a room number alone. It should carry a dimensioned elevation, a finish code, a glass schedule and an electrical note. Those four documents are what stop variation creep between the sample room and the remaining floors.

Step 5: Order it inside one procurement package

Media units rarely fail on their own; they fail because the wall behind them, the flooring level, or the lighting circuit was coordinated by someone else. As a hotel furniture and fit-out supplier, we produce built-in joinery alongside the engineered wood flooring, wall panelling, doors, lighting and loose furniture that surround it, so a single set of drawings governs the whole room.

For hotel and serviced-apartment buyers this shortens coordination in three concrete ways:

  • One finish schedule covers cabinetry, panelling and profiles, so samples are approved once.
  • Openings, levels and service routes are resolved between our own production teams instead of across separate suppliers.
  • Freight, packaging and container loading are arranged together, which reduces the risk of a cabinet arriving before the wall it fixes to.

Our custom & OEM service covers bespoke finishes and layouts, and project work runs through design coordination, production, logistics and installation support under one contract.

Common mistakes we see on hospitality enquiries

  • Specifying glass frontage first and discovering later that the screen mounting needs a reinforced substrate behind it.
  • Ordering one unit type across all room categories, then finding suites need a different composition from standard rooms.
  • Leaving cable routes to site fitters, which produces visible trunking on a wall designed to look clean.
  • Treating dimensions as fixed. These units are made to the project; send finished-line dimensions and let the set-out follow them.

Checklist before you request a quotation

  • Room-by-room elevation with finished-line dimensions.
  • Screen size, mounting method and connection locations per room type.
  • Glass and finish schedule matched to the wider joinery package.
  • Storage inventory: what is displayed, what is concealed, at what heights.
  • Confirmation of lighting inclusion, driver positions and switching.

Send those five items and the quotation comes back against a defined scope rather than an estimate that moves after the sample room is built.

Planning guest-room or suite joinery? Send us your room elevations and finish schedule, and our project team will configure glass front media units to your layout — with production, logistics and installation support under one package.

Contact SANTERSON — PHILLIP, +86 139 2821 4007