A wall sconce is a small line item on most schedules and a large source of rework when the wrong quantity, finish or fixing detail reaches site. This guide sets out how we count fixtures across guest rooms, corridors and bathrooms, and how each sconce is coordinated with the mirror, vanity, cabinetry and lighting circuit around it.

Our Santerson Wall Sconces collection is made to measure: finish, layout and dimensions are set per space rather than chosen from a fixed catalogue size. That flexibility helps on bespoke villa and hotel work, and it also means quantity planning has to be done properly. A single fixture ordered short in a 120-key hotel means an unmatched replacement months later, because the batch, the finish lot and the wall condition are no longer the same.

Start with the room type, not the fixture count

Counting sconces one by one from a reflected ceiling plan is where mistakes begin. Group the rooms first, then fix a standard for each group. On a hospitality or villa project we normally see four:

  • Guest room and bedroom. Typically a pair at the head of the bed, plus one or two in the dressing area. Bedside sconces have to sit clear of the door swing, the wardrobe return and the switch plate.
  • Bathroom and powder room. One either side of the mirror, or a single decorative piece above it. Here the sconce competes with the mirror, the basin tapware and the tile setting-out, so all four need to be on one drawing.
  • Corridor, stair and lift lobby. Repeated at a consistent height and spacing, usually set out against the floor tile module or the joinery rhythm rather than an arbitrary grid.
  • Lounge, study and feature wall. Often one-off sculptural pieces where the visual composition matters more than the count.

Once each room type has a standard, the quantity follows from the room schedule. Send us the room schedule and the reflected ceiling plan together and we will mark up the fixture per room type, so the order is built on your own numbering system rather than a count that nobody can check later.

How to set the order quantity

For made-to-measure fixtures there are three numbers, not one: the design quantity, the spares quantity and the hold-back. The table below shows how we normally build them up with project teams.

Quantity element How it is set Why it matters for sconces
Design quantity Fixtures shown on the approved reflected ceiling plan, per room type, multiplied by the room count. This is the base order. Every fixture must carry the same room code as the drawing so the packing list can be checked against it.
Spares A reserve held on site for the whole defects-liability period, sized to the number of rooms and how exposed the fixture is to traffic and cleaning. Reproducing a made-to-measure finish after handover takes a new production run. Spares ordered in the original batch match lot and finish.
Hold-back A small number of fixtures left unordered until the mock-up room is signed off. Height, spread of light and finish all read differently on a finished wall than on a sample board. Hold back until the mock-up is approved.
Breakage allowance Fixtures with glass shades or diffusers carry a handling allowance for transit and site storage. Glass components are the usual loss point. Confirm the allowance before the packing list is frozen, not after the container arrives.

We do not publish a fixed minimum order quantity for this collection. Flexible MOQs form part of our custom and OEM service, so the split between design quantity, spares and hold-back is agreed with you per project.

Coordination: what has to be resolved before the order

A sconce fails on site for two reasons more than any other: it clashes with something already fixed, or the electrical provision behind it does not match the fitting. Both are solved on paper.

1. Mirror, vanity and basin

In bathrooms the sconce is set out against the mirror first. Decide whether the fixture sits beside the glass or above it, then confirm the height against the tallest user and the tapware projection. Where a mirror with integral lighting is preferred instead, our Vanity Lighting range covers that case, and choosing it early avoids two competing light sources on one wall.

2. Joinery and concealed wiring

Where a sconce lands on custom cabinetry or a wall panel, the back box has to be built into the joinery drawing before manufacture, not cut on site. If the joinery also carries tape or profile lighting, we coordinate that with our Integrated Cabinet Lighting so one driver and one switch arrangement serve both.

3. Circuit, switching and dimming

Confirm the circuit, the switch location and whether the fixture is on a dimmer before production. Drivers, dimming gear and fitting have to be compatible as a set; this is settled at order stage with your electrical consultant.

Technical data to close out per project: our captured product pages do not state lumen output, wattage, colour temperature, IP rating or electrical compliance for these fixtures. Those values are confirmed in writing with your lighting consultant and electrical contractor for each configuration before manufacture, along with fixing details for the actual wall build-up — tile, plasterboard, stone or joinery.

Mixing decorative and architectural sconces

Most projects need two families of wall lighting: an architectural piece repeated in the hundreds, and a decorative piece used at entrances, feature walls and powder rooms. Keeping them on separate line items stops the decorative fixture being substituted to save cost when quantities are trimmed.

Within our range, pieces such as the Modern Splash Mirror Wall Lamp work as a single decorative feature over a basin or on a vanity wall. The Modern Balance Arm Wall Lamp gives directional light where a reading or task position needs it, beside a bed or at a study. For corridor and bedside repetition, the Modern Dome Wall Lamp and Modern Arch Ball Wall Lamp cast soft ambient light and hold up well when repeated down a run.

Mock-up, then release the full quantity

Before we run production on the full order, install one room or one corridor length as a mock-up. Check four things on the finished wall: mounting height, spacing between fixtures, how the light falls on the actual paint or stone finish, and whether the shade reads well from the main sightline. Sign it off, then release the balance including your hold-back.

  • Room schedule and reflected ceiling plan issued together, with a room code on every fixture
  • Sconce set-out agreed against mirror, basin, tapware and tile module
  • Back-box positions shown on joinery and wall-panel drawings where the fitting lands on them
  • Circuit, switching and dimming confirmed with the electrical contractor
  • Lumens, wattage, colour temperature, IP rating and compliance signed off per configuration
  • Spares and breakage allowance on the purchase order, not added later
  • Mock-up approved before the balance of the quantity is released
Send us your room schedule, reflected ceiling plan and finish schedule and we will mark up the sconce type and quantity per room, coordinate it with the mirror, joinery and lighting circuits around it, and quote the full package. As a one-stop furniture and building materials supplier we produce these fixtures alongside the cabinetry, wall panels and bathroom fittings they sit against, so coordination happens inside one production programme rather than between several suppliers.