A swim spa rarely fails at approval because of its appearance. It stalls at the point where a beautiful render meets a real site: the slab, the power supply, the drainage route and the delivery window all have to agree before anyone signs. Outdoor Swim Spa WS-P001 is a compact hydrotherapy unit in our swimming pool range, and it is exactly the kind of product that rewards a team that asks precise questions early. Below is the checklist we would run with an architect, main contractor or developer before the purchase order goes through.

1. Confirm the footprint and weight allowance with a structural check

The catalogue dimension for WS-P001 is 3500 × 950 mm. Treat that as the shell to be accommodated, then check three things on site: the clear opening or access route the unit travels through, the prepared base and — where the spa sits on a deck, terrace or upper level — the load allowance signed off by the structural engineer for a fully filled vessel plus occupants, and whether the surrounding paving, decking or coping will raise the finished floor above the spa rim. A difference of a few centimetres between architectural levels and structural levels is the most common reason a swim spa arrives and cannot be set.

Ask the site team for a surveyed dimension of the prepared base, taken after waterproofing and finishes are installed, not from the original plan. Confirm access for the delivery crew at the same time — side yards, gates and overhead beams routinely block placement of a rigid shell of this size.

2. Confirm the electrical supply before it is quoted

The listed total power for this configuration is 8.35 kW. That figure covers the standard equipment shown on the product page, and it changes the moment options are added. Before approval, your electrical consultant should confirm:

  • the available supply capacity at the intended position, and whether a dedicated circuit and isolator can be run to it;
  • the local voltage, phase and earthing arrangement, which differ by market and by building type;
  • where the control system will sit, and how it will remain reachable for routine operation and servicing;
  • who is responsible for the connection work — normally the main contractor, with the equipment supplier providing the requirement.

Do not let a heat pump or additional pumps be added to the specification after the electrical design is frozen. Adding a Customizable Shape Outdoor Spa option such as a heat pump changes both the load and the distribution board, and revising that late is expensive.

3. Confirm exactly which equipment is in the quoted configuration

WS-P001 is listed with two water pumps, one filter pump, 81 jets, two LED lights and one control system, with water jets, LED lighting and ozone shown as features. Two cautions apply to every project specification:

  • Optional accessories — control systems, UV sterilisation, extra water pumps, heat pumps, sand filtration, insulation and steps — are available across the range, but availability and compatibility vary by model. What is offered on one shell may not fit another.
  • A swim training system is not listed for this model. If a client's brief says "lap swimming", raise that in writing now rather than discovering it at handover; longer formats exist elsewhere in the range, such as the Long Outdoor Swim Spa with Hydrotherapy & Relaxation Pool.

Request a written configuration sheet with your quotation that names each item, its quantity and what is excluded. That single document prevents most disputes at handover.

4. Confirm the plant, drainage and maintenance access

Filtration and access panels need clearance, not just a hole in the deck. Before sign-off, confirm where the filter pump is reachable from, how the cover or lid lifts, whether overflow and drain-down water can reach a suitable drain, and how much space the maintenance crew needs to remove a pump without lifting paving. A plant zone that only exists on paper becomes an expensive snag list later.

Insulation and cover arrangements also affect running cost, so specify them explicitly rather than assuming they are included.

5. Confirm the delivery route, sequence and responsibilities

A swim spa is a single rigid item that has to arrive after the base is ready but before the surrounding finishes are closed in. In our Swimming Pools and Swim Spas programme we coordinate production, packing, container loading and door-to-door delivery as part of a turnkey package, so the delivery date can be tied to the site programme rather than left to chance. What the project team still needs to confirm locally:

  • the agreed Incoterms, import terms and who pays duty and clearance;
  • a firm delivery window and a crane or crew for placement if required;
  • storage on site — the unit should not sit in the open waiting for the slab;
  • the inspection point at handover, with a signed snag list.

6. Confirm warranty scope and the service contact in writing

Ask which components are covered, for how long, what is excluded, and who attends on site. Our services include installation support, inspection and snagging, spare parts and ongoing maintenance, but response arrangements and warranty terms vary by project and market, so we confirm them per contract rather than quoting a generic promise.

The five documents to have in hand before approval

DocumentWho provides it
Surveyed base dimensions, level check and structural load sign-offSite contractor and engineer
Electrical requirement sheet and board scheduleSupplier and electrical consultant
Configuration sheet listing included and excluded itemsSupplier
Delivery plan with access route and placement methodSupplier and site contractor
Warranty terms and service contact for the projectSupplier

If all five exist, WS-P001 can be approved with confidence. If any one is missing, hold the approval and close that gap first — it costs a day in the office and saves weeks on site.

Send us the model reference, your site drawings and the intended market, and we will confirm the configuration, electrical requirement and delivery plan for your project before you commit to a programme date. Contact SANTERSON to start that review.