Glass and glossy wall panels look flawless on a sample board and in a render. The finish is what sells the panel — and the finish is also the part most likely to be damaged between the factory and the site. If you are specifying Santerson Glass & Glossy Panels for a villa or apartment project, the packaging conversation is not an afterthought to be left to the freight booking. It belongs in the same quotation round as size, finish and layout.

Why glossy and glass panels are a different packing problem

Our Paneling Systems range is made to measure: dimensions, layout and finish are set per project rather than picked from a stock size. That has two direct consequences for packaging.

First, there is no spare in the crate. A made-to-measure panel that arrives chipped at a corner or with a scratched face is not something the site can make good with an off-the-shelf replacement; it goes back into production and into another container cycle. Second, glossy surfaces show handling damage immediately. A matte surface can hide a scuff; a reflective one turns a small abrasion into a visible flaw under site lighting, and it usually shows up only after the panel is already on the wall.

So the goal of packaging here is not simply "get the crate to port". It is to keep each panel flat, supported, separated from its neighbours and identifiable against your layout drawing when the crates are opened in the sequence the rooms need them.

Ten points to confirm before production starts

  • Panel thickness and edge detail as shipped, and whether edges are protected or capped on all four sides.
  • Face protection: what separates the glossy face of one panel from the back of the next, and whether that interleaf is soft, non-abrasive and dry.
  • Edge and corner protection at the crate corners, which is where impacts concentrate during handling and container stuffing.
  • Crate construction — timber crate or plywood case, and whether panels travel flat or upright on edge. State which, and confirm the same orientation is used for unloading.
  • Panel identification: each crate and each panel marked with a number that matches your approved layout drawing, not just an internal order code.
  • Crate dimensions and gross weight, so you can check lift capacity, door widths, corridor turns and lift access at the project before delivery day.
  • Handling marks on the outside of the crate: this-side-up, fragile and keep-dry labelling, plus centre-of-gravity marking on tall crates.
  • Moisture protection for sea freight — desiccant or vapour-barrier wrapping where panels are stored on site before installation.
  • Whether glass components, if included in your configuration, travel in the same crate as the panel substrate or separately.
  • Spare and replacement terms: how a damaged panel is reported, photographed and re-produced, and what packaging that replacement will travel in.

Ask for all of this in writing at quotation stage. Packaging details confirmed after production begins are usually treated as a variation, because crate sizes have already been cut to the panel schedule.

How the packing list should read on arrival

A useful packing list for a panel order does more than count crates. It should let a site team reconcile delivery against the layout drawing without opening anything.

Crate number and total crate countConfirms nothing was left behind at the port or dropped in transit.
Panel code inside each crate, mapped to the room or wall elevationLets panels be routed straight to the right floor instead of being stacked and re-sorted.
Finished size and thickness per panel codeCatches a sizing error before adhesive and trims are committed.
Finish reference as approvedProtects you if two batches of a glossy or lacquered surface differ in sheen.
Gross and net weight, crate dimensionsNeeded for lift bookings, floor protection and labour planning.

If your supplier's logistics team handles the freight as well as the production, ask them to confirm that the crate markings and the packing list use the same codes. Mismatched codes are the most common reason a panel order sits in a loading bay for days.

Inspecting the shipment: what to do in the first ten minutes

Photograph the crates before anything is opened, including the vehicle plate and any shrink-wrap damage. Then check crate integrity — punctures, splits, water staining, crushed corners — against the packing list count. Only after that should faces be inspected, ideally with two people present so there is no dispute about what was found.

Keep damaged crates closed until they have been photographed; a collapsed crate tells a different story once its contents are loose. If a face flaw is found, photograph it in raking light, which shows surface damage that flat lighting hides, and record the panel code from the crate marking. That combination is what makes a replacement claim straightforward rather than an argument.

Storage matters as much as transport. Glossy and glass panels should stay in their crates, standing or lying as marked, on dry level ground, acclimatising in the same environment where they will be installed. Panels moved straight from a cold container into a warm, humid room can sweat, and moisture against a protected face is how staining and adhesion problems start.

Combining panels with other fit-out items in one shipment

Panel orders rarely travel alone. A bathroom or bedroom wall package usually sits alongside Wall Panel Systems, Custom Niche Paneling and cabinetry, and consolidating them into one container saves freight but changes the packing question: heavy joinery must not share a crate with a glossy panel, and the lighter panels should not be loaded on top of cabinet carcasses.

Where you are mixing finishes across the same wall — for example Santerson Matte Lacquer Panels next to a glossy panel — confirm that both are packed with face protection, because matte surfaces mark differently and transfer grit onto the gloss face they rest against. Agree the loading sequence too: panels for the last room to be finished should be loaded first, so the crew is not unloading a villa in reverse order.

Questions buyers most often ask us

Can panels be shipped flat with other materials in one container?

Yes, subject to the loading plan. Panels travel on a stable base, restrained so they cannot shift, and never under heavy loose cargo. We confirm the stowage plan before stuffing.

What if a panel is damaged after it has been delivered and signed for?

Send photographs of the crate marking and the flaw in raking light, together with the panel code from the packing list. We review that against the production record and arrange re-production where it is warranted.

Do made-to-measure panels come with spares?

Not as a rule — that is the point of made-to-measure. If your design repeats a panel across several rooms, tell us at quotation stage whether you want extra units produced in the same batch, so they are packed and marked as spares.

Before you place a panel order, send us the wall elevations, the finish references you have approved and the delivery access constraints on site. We will come back with the panel schedule, the crate marking scheme and the packing list format your site team will actually receive — so the packaging terms are settled while they are still cheap to change. Contact PHILLIP on WhatsApp +86-13928214007 or email santerson@qq.com.