A swim spa that arrives on site and then needs re-engineering is an expensive lesson. The Outdoor Swim Spa WS-PC05ST-S is one of the more specified models in our configurable outdoor swim and hydrotherapy range, and every unit we build for it starts with the same set of confirmations. This article lists exactly what we ask a buyer or project team to lock down before production begins, so the shell, equipment and site conditions all match on the day the spa is installed.
Start With the Site, Not the Catalogue
The catalogue entry for this model gives dimensions of 5000 × 2400 × 1470 mm. Treat that as the reference footprint, and then check it against the actual ground conditions where the spa will sit: a terrace slab, a garden patio, a villa pool deck or a resort leisure zone each behaves differently. Confirm three things in writing before we open a mould order:
- The finished level of the supporting base, including drainage falls around the shell, so the spa does not end up standing proud of the surrounding finish.
- Access for delivery and positioning — doorway widths, turning radii, crane or forklift reach — because a fully equipped unit is not something that can be re-cut on site.
- Where the plant and control system will sit relative to the shell, and how the cable runs will reach it.
Confirm the Equipment List Line by Line
The specifications shown for this model include one control system, one swim training system, one filter pump, six water jets in total and four LED lights, with a total power figure of 6.55 kW. Two points deserve attention before an order is placed. First, the water pump is not listed on the catalogue page, so it must be agreed as part of the configuration rather than assumed. Second, the power figure is the equipment load shown for that configuration — your electrician needs it to size the supply, protection and any isolation between the spa circuit and other outdoor circuits.
The features displayed for this model are water jets, LED lighting, ozone and a swim training system. Ozone is a sanitisation option, not a substitute for filtration and water chemistry management, so we discuss how it is intended to work alongside the filter pump in your specific use pattern.
Decide Which Options Belong in Your Climate and Use Pattern
Catalogue-listed options for this range include control systems, UV sterilisation, water pumps, heat pumps, sand filtration, insulation and steps. Availability and compatibility vary by model, so we confirm each item against the selected configuration rather than offering a generic upgrade list. A spa used for year-round training in a cool climate and a spa used seasonally on a shaded city terrace do not need the same option set — insulation and a heat pump matter far more in one case than the other, while steps and entry height matter more where children or older users will be in the water.
If you are comparing footprints, the closely related Outdoor Swim Spa WS-PC05ST-L is listed at 5490 × 2400 × 1470 mm, and the standard Outdoor Swim Spa WS-PC05ST shares the 5000 mm length. Send us the usable rectangle of your space and we will tell you which of these fits without a site compromise.
Agree the Shell, Finish and Water Feature Details
This model is built on an acrylic shell with structural reinforcement. What needs confirming is how that shell meets your finish: shell colour against the surrounding paving or cladding, the position of the jets relative to seating depth, and how the LED fittings read at night against the landscape lighting scheme. Where a project calls for a non-standard geometry rather than the catalogue form, our Customizable Shape Outdoor Spa covers square, round, oval and curved configurations for gardens, terraces and luxury leisure areas.
Electrical, Water and Handover Documentation
Before production we close out the technical paperwork with the buyer's team. That means the supply requirement for the agreed configuration, the control system interface, the filtration and sanitisation arrangement, and the spare-parts position for wear items such as jet fittings and lighting. We also confirm what is supplied by us and what stays with the local contractor — base preparation, power supply, water feed and any drainage work are normally site-side scope.
How Our Process Runs Once the Details Are Locked
SANTERSON has operated as a China-based furniture and building materials manufacturer since 2008, supplying villa, hospitality and office projects with an integrated scope that runs from design and production through to door-to-door delivery. For a swim spa order the same sequence applies: we review your drawings and site information, confirm the specification and quotation in writing, produce the unit, then arrange freight and coordinate installation support. Our project services cover custom and OEM work, logistics and door-to-door delivery, and installation and after-sales support.
Because swim spas sit alongside the rest of a project's fit-out — outdoor furniture, paving and cladding, bathroom products, lighting — buyers working on villas and resorts often group them into one procurement package. Our swimming pools and swim spas range can be specified together with the surrounding outdoor furniture and finishes, which keeps a single point of responsibility across the terrace.