A procurement brief is the document that decides whether a set of lacquer-finish wardrobes arrives as specified or arrives as a compromise. For bedroom joinery packages, Neutral Tone Lacquer Wardrobes are usually ordered made-to-measure, with the finish, layout and dimensions confirmed project by project. That flexibility is an advantage for villa and apartment work, but only if the brief states clearly what has to be delivered, what still needs confirming, and who signs off on each decision.

Before drafting the brief: decide which items in your package are fixed (sizes, room list, handover date) and which are open (exact sheen level, door construction, internal fittings). The value of a good brief is that it separates the two, so quotations compare like for like.

1. Scope and room schedule

Start with the physical inventory rather than the finish. A wardrobe line item without a room reference is impossible to price or install consistently across several units.

  • Unit, floor and room reference for every wardrobe, plus the wall run each one sits in.
  • Overall width, height and depth as designed, with a clear note on whether the dimensions are finished sizes or structural openings that still need packing out on site.
  • Whether the unit runs to the ceiling, stops below a bulkhead, or wraps around an existing corner.
  • Quantities by type, so identical bedrooms in a multi-unit project are grouped instead of described one by one.

If your drawings and your bill of quantities disagree on a dimension, say so in the brief and ask for the discrepancy to be resolved at quotation stage. Discovering it after production has started is the most expensive place to find it.

2. Finish: describe the neutral tone precisely

"Neutral lacquer" covers a wide range of warm greys, putty tones, off-whites and taupes. Two suppliers can both deliver a compliant neutral and produce visibly different rooms. Specify the finish in three parts:

  • Colour reference. A named standard or an approved physical sample. If you work from samples, state who holds the master sample and how many approvals are needed before colour is fixed.
  • Sheen level. The Lacquer Wardrobes collection includes both High Gloss Lacquer Wardrobes and Matte Lacquer Wardrobes. A neutral tone behaves very differently at each end of that range: gloss reflects light and shows fingerprints and edge lines, while a matte or low-sheen surface reads softer and hides handling marks better.
  • Application to all visible faces. Door fronts, door backs, reveals, shelf edges and any returned panel should be called out as the same finish, or deliberately stated as different. Mixed-face specification is common where a wardrobe also acts as a room divider.

Where a bedroom scheme combines closed lacquer doors with open storage or glass-fronted sections, list those combinations in the brief. The collection also covers Two Tone Lacquer Wardrobes and Glass & Lacquer Combination Wardrobes, so a mixed elevation is normal to request — it just needs to be described on paper, not left for the shop drawings.

3. Construction and door type

Door type drives clearance, cost and how the wardrobe behaves in a small bedroom. State the operating type per unit and note any constraint that rules an option out:

Item to specifyWhy it belongs in the brief
Sliding or hingedSliding doors save swing clearance in narrow walkways; hinged doors give full opening access and need clear space in front of the unit.
Frame and panel detailFlat, flush fronts read as built-in joinery; framed or panelled fronts change shadow lines and how the unit meets skirting and wall finishes.
HardwareHinges, slides, handles or integrated pulls, soft-close where required, and whether hardware is supplied with the unit or by others.
Carcase substrate and edge treatmentAsk what substrate carries the lacquer and how edges are finished; both affect appearance at reveals and long-term durability.
Integration with adjacent workWhere wardrobes meet matte lacquer panels or matching wall panelling, the interface detail should be agreed before either trade is ordered.

For multi-unit projects, note whether the same construction has to repeat across every unit. Repeating a single detail through several bedrooms is what keeps quotations and site labour predictable.

4. Internal layout and storage planning

The internal plan is where user-facing complaints usually originate, because it is often decided late. Give the brief a hanging-to-shelf ratio, drawer counts, and any dedicated zones:

  • Long-hang, double-hang and short-hang runs, with heights.
  • Drawer banks — number of drawers, widths, and whether they sit under hanging rails or in a tower.
  • Open shelving for folded storage, plus shelf depth and spacing.
  • Specialist items: lighting inside the carcass, mirror panels on doors, ironing or valet provisions, safes in hospitality rooms.

Modular layouts are an easy way to keep a multi-bedroom project consistent. If some bedrooms will take Combination Modular Wardrobes rather than a single made-to-measure carcass, say which rooms and why, so the quotation reflects the same logic you designed with.

5. Site conditions and interface responsibilities

Wardrobes are measured against walls that are never quite as drawn. Put the site conditions in the brief, along with a line-by-line statement of who does what:

  • Floor finish build-up and whether it is complete before templating.
  • Ceiling level, bulkheads, cornices and any services running above the unit.
  • Electrical provision for internal lighting: who runs the cable, who terminates it, and where the isolator sits.
  • Skirting, architrave and paint — whether the wardrobe supplier returns and finishes edges, or the painter does.
  • Who protects installed units while other trades finish the room.

This section also protects your programme. If templating cannot happen until flooring is laid, that dependency belongs in the brief and then in the production schedule.

6. Approvals, sampling and quality checkpoints

State the approval route you expect, with names and stages, so nothing is produced on an assumption:

  1. Shop drawings for dimension and layout sign-off, issued against your latest drawing revision.
  2. Finish sample or mock-up panel approved before full production of the finish.
  3. Production release only after both are signed — with a stated cut-off date after which changes carry cost and time.
  4. Pre-shipment inspection notes or photographs for the batch, and an agreed snag process on site.

A single approved sample set settles most colour and sheen disputes before they reach a completed room. For projects with several bedroom types, one approved reference per finish type is usually enough.

7. Packaging, delivery sequence and installation

Joinery fails on site as often from handling and sequencing as from manufacturing. Ask the brief to cover:

  • Packaging standard and protection of lacquered faces in transit.
  • Labelling by unit and room reference, matching your room schedule — this alone saves hours of unpacking.
  • Delivery sequence per unit or floor, not one undifferentiated drop.
  • Storage arrangements on site, and who provides them.
  • Whether installation is by the supplier's team or your own, and how snags and replacements are handled afterwards.

For projects sourced across borders, also fix shipping terms, the documents you require with each consignment, and the point at which risk transfers. Confirm import duties, transit time and delivery scope for your specific site rather than assuming a standard service level.

8. Commercial terms worth locking down

  • What the quoted price includes: measurement, drawings, hardware, delivery, installation, taxes and freight.
  • Validity period of the quotation, and how finish changes are priced.
  • Payment stages tied to drawing approval, production release and despatch.
  • What is covered after handover, for how long, and what is excluded — ask for the written terms rather than a verbal assurance.

If you are comparing suppliers, issue the same brief to each and require them to list exclusions in writing. Differences between quotations then show up as scope gaps instead of surprises at installation.

Working with a made-to-measure manufacturer

SANTERSON is a China-based furniture and building materials manufacturer supplying project customers, with custom and OEM work covering bespoke dimensions, material and finish choices, and prototyping alongside production. Its wardrobe range is specified per project — sizing, layout and finish are confirmed against the drawings rather than chosen from fixed catalogue sizes.

That route suits briefs that arrive with a room schedule and a finish direction already in place. It also pairs well with coordinated built-in furniture, where wardrobes, vanities and wall panelling are produced to one detail language instead of being reconciled between separate trades.

Send the brief with your drawings and finish references, then require shop drawings and an approved finish sample before production release. That single sequence is what keeps a neutral lacquer scheme looking like the drawing once the doors are on.

Product configuration, dimensions and selected specifications must be confirmed for each project. Terms such as warranty coverage, response times and delivery scope should be agreed in writing per contract.