A black acrylic wardrobe is one of those products that looks simple on a drawing and turns complicated on site. The door surface reads as a flat, deep black panel, so buyers assume the only decisions are colour and width. In practice the quotation depends on a whole set of inputs: room dimensions to the millimetre, what sits behind and above the unit, how the doors will open, what goes inside, and who is going to lift it into place. Send that information with your first enquiry and you usually get an accurate price the first time round. Leave it out and the order stalls while drawings go back and forth.

This guide sets out the measurements and project details we need to specify black acrylic wardrobes for a bedroom, dressing room or villa fit-out, and explains what each one changes.

Why black acrylic rewards accurate input

Acrylic door panels are manufactured to size. There is no trimming on site to absorb a 40 mm error, and a slab that arrives too tall for the recess cannot be shortened without ruining the finish. Black in particular behaves differently from pale colours: light reflects off it sharply, so panel alignment, edge condition and the gap between doors all become visible at close range. A wardrobe specified with correct reveal widths and a true, square opening looks built into the architecture. The same wardrobe specified loosely looks like furniture that arrived late.

Our acrylic wardrobe line is made to measure rather than offered in fixed cabinet widths. Alongside the black finish, the collection covers matte acrylic wardrobes for rooms where fingerprints and reflections are a concern, two-tone acrylic wardrobes when a full-black wall feels too heavy, and white acrylic wardrobes for the opposite side of a scheme. If you want doors that break the flat plane, glass and acrylic combination wardrobes put glazed fronts into part of the run.

The core measurements: width, height, depth

Start with three dimensions per wall, not one. Take each measurement at the top, middle and bottom of the opening, because floors are rarely level and walls are rarely plumb in existing buildings. Report the smallest figure as the constraint and note the variation.

MeasurementHow to take itWhat it decides
Total run widthWall to wall, or to the nearest obstruction such as a door reveal, radiator or column. Measure at high and low level.Number and width of doors, module split, whether an end return is needed
Clear heightFloor finish to ceiling, or to the underside of a bulkhead, pelmet or beam. Note any skirting that must be cut around.Whether the unit reaches the ceiling, and whether a top section for storage is possible
Available depthWall face to the nearest obstruction across the room, including bed frame, door swing and radiator.Cabinet depth, door type, and how much hanging space you actually get

Depth is the measurement buyers most often take for granted. A standard wardrobe body is deep enough that a hinged door can open across the front of it without fouling the bed or the opposite wall. Where the room is shallow, sliding doors solve the clearance problem but cost you the depth of the door track and about half of the visible frontage at any one time. Tell us the clear floor space in front of the unit as well as the depth of the recess, and we can recommend a door type instead of guessing.

Room conditions that change the specification

A new-build shell and an occupied bedroom are different jobs. Before we draw anything we need to know what is already there.

  • Floor finish status. Is the screed, tile or timber already laid to final level? If not, tell us the intended build-up so the height on the drawing accounts for it.
  • Skirting and architrave. Built-in units usually scribe around existing profiles. Send a photo and note the skirting height if you want the unit pushed flat against the wall.
  • Wall construction and load path. Stud partition or masonry matters for tall units that need fixing back, and for anything with an overhead section.
  • Obstructions. Sockets, switches, light points, radiators, air-conditioning grilles, window reveals and door swings all move the module boundaries.
  • Access route. Lift dimensions, stair width, corridor turns and the final carrying path to the room. Full-height acrylic slabs and one-piece carcass sections are not small parcels.
Where a room is being stripped back, measure after the plaster and floor finishes are complete. Measure before, and send us the finish build-up so we can allow for it on the drawing.

Interior layout: what actually goes inside

The internal plan is where a made-to-measure wardrobe earns its price. Work out how you use the space before choosing any fittings, then send us the list.

  • Hanging. Short hanging for shirts and jackets, long hanging for coats and dresses, or double hanging stacked one above the other. Long hanging needs considerably more height than most people allow.
  • Drawers. How many, and whether they sit in the base below hanging rails or at waist height in a chest section. Internal drawer banks are the usual answer for folded knitwear.
  • Shelves. Adjustable shelving for boxes and bags; fixed shelf heights only where contents are known.
  • Open display. Open bays, glass-fronted sections or niche lighting break up a long black frontage and make the unit easier to live with.
  • Accessories. Trouser rails, tie and belt slides, jewellery trays, valet rods, integrated lighting, safe, laundry hampers in a base cabinet.

If a bedroom run cannot hold everything, walk-in layouts carry the overflow. Our L-shaped walk-in wardrobes and U-shaped walk-in wardrobes use the same acrylic fronts and carcass detailing, so a bedroom unit and a dressing room can be ordered as one package with a consistent finish. For rooms where the plan is tight, L-shaped corner wardrobes keep a corner usable without wasting the return.

Door type, opening geometry and clearances

The door decision follows from the room, not from taste alone. Hinged doors need clear floor space in front of every door leaf for the duration of its swing. Sliding doors need a wall or panel alongside to receive the sliding leaf, plus headroom for the track. Where a hinged run has to return around a corner, the corner detail and the door stop have to be drawn deliberately.

For reference, our matte sliding door wardrobes and high gloss sliding door wardrobes show how the same principle applies across finishes; the acrylic version follows the same track and clearance logic. Send a simple plan of the room with furniture positions and door swings marked, and we will tell you which door type the room supports before pricing.

Finish, substrate and edge details

Black acrylic is not one surface. High gloss black reflects the room back at you and enlarges a narrow space; matte and soft-touch black reads as a flat, quiet surface and hides handling marks. The two look completely different once installed under bedroom lighting, so ask for the finish sample before you commit to a whole wall of it.

  • Sheen level. Gloss, satin or matte, confirmed against a physical sample rather than a screen.
  • Edge treatment. How door edges are finished and whether they are matched to the face. On black this is the detail that decides how crisp the frontage looks.
  • Carcass colour. Whether interior boxes match the exterior or use a lighter tone, which changes how visible dust and shadows are inside an open compartment.
  • Handle strategy. Profile handles, integrated pulls or push-open hardware. Hardware choice affects the door gap and whether adjacent leaves can be opened at once.
  • Matching joinery. Wardrobe fronts can be repeated on bedside panelling, mirrors and window seats so the room reads as one scheme.

Material and finish options are specified per project. Where a bedroom needs a different surface from the dressing room, mixing finishes within one order is normal — for example black doors on the main run with white acrylic doors in an alcove.

Documentation to send with your enquiry

The faster enquiries share the same packet of information. You do not need a full drawing set to start.

DocumentMinimum acceptable version
Room plan and elevationsHand-measured sketch with all dimensions written on it, plus photographs of each wall from standing height
Existing drawingsArchitectural or joinery drawings in PDF, even if the wardrobe is not drawn on them yet
Finish directionMood board, reference photograph or the finish you have already chosen for other joinery in the project
Internal requirementsA written list of hanging, drawer and shelf quantities per unit
Project contextLocation, storey, lift and access details, target installation window, and whether other joinery is being ordered at the same time

How the order runs from enquiry to handover

The process follows the stages we run on any fitted project: consultation, design and planning, production, logistics, installation and after-sales. For wardrobes that means a first quotation against your dimensions, then drawings for sign-off with module splits, door sizes and internal fittings marked, then manufacture to the approved drawings.

For projects outside China we arrange freight by sea, air or rail with the customs paperwork handled on our side, and delivery to site. Because acrylic fronts are surface-sensitive, they travel protected and packed for handling rather than in standard flat-pack cartons, and the packing list identifies each section against the drawing number so the installation crew can follow the sequence.

Installation is where a black acrylic wardrobe is either finished or ruined. Panels must be aligned on all four edges, doors adjusted so the reveals run parallel, and the surrounding plasterwork left clean. On-site inspection covers alignment, door operation, drawer runners and any snagging before handover, with spare parts available for later replacement.

Confirm dimensions and selected specifications against the signed drawing before production starts. Once panels are cut to size, changes to width or height mean remaking doors, not adjusting them.

A practical pre-order checklist

  • Width, height and depth measured at multiple points, with the smallest figure identified
  • Floor finish level confirmed, or the intended build-up stated
  • Clear floor space in front of the unit measured against the door swing
  • Sockets, switches, radiators, grilles and beams marked on the sketch
  • Hanging, drawer and shelf quantities listed per unit
  • Finish sheen chosen from a physical sample, not a photograph
  • Access route to the room checked for full-height sections
  • Other joinery in the same finish identified so colour and edge detail match across the project

Putting it together

Specify a black acrylic wardrobe by giving us the constrained dimensions, the room conditions around it, the internal layout you need, and the access route to the room. With those four inputs we can draw the module split, recommend a door type that the floor space supports, confirm the finish against a sample and price the job without a second round of questions.

Send your measurements, sketches and photographs through our contact page, or speak with PHILLIP on WhatsApp +86 13928214007. We supply fitted wardrobes and full joinery packages for villas, hotels and residential projects, with the same finish carried across cabinetry, panelling and built-in storage.