A wall hung bidet rarely fails because of the ceramic. It fails because the fixing frame, the waste connection and the clearances around the bowl were decided after the tiles were ordered. If your installation plan for the Wall Hung Bidet 1004F is being drawn now, here is the list of items that should already be on it before any material is ordered.
What the 1004F actually gives you
Model 1004F is a wall-mounted bidet in solid vitreous ceramic with a smooth glossy glaze, fixed to the wall through its back panel. The rectangular outline carries rounded corners, so it reads as a modern piece without sharp edges at hip height. Because nothing touches the floor, the tile beneath stays clear and mopping the bathroom floor is a single pass rather than a scrub around a pedestal.
The published dimensions are 545 mm long, 360 mm deep and 410 mm high. Treat those numbers as planning references until your technical sheet for the production batch is in hand; trap arrangement, rough-in depth and the applicable product standard should all be confirmed on that sheet before the wall is closed up.
Items that belong in the installation plan
1. Supporting wall and concealed frame
A wall hung bidet carries a loaded body, so the plan must state what holds it: a steel fixing frame inside a stud partition, or direct fixings into masonry with a suitable bracket arrangement. The plan should record the finished rim height you intend to work to, the position of the fixing points relative to the finished floor level, and whether the wall build-up is thick enough to take the required fixings without breaching the opposite face.
2. Water supply and mixer position
- Hot and cold isolation points, set out on the centre line of the bidet and at a height that stays behind the pan but stays reachable for maintenance.
- The mixer or bridge set you intend to use, with its spout reach checked against the rim so water lands in the bowl and not on the glaze edge.
- Whether tap holes are pre-formed on the production unit for your chosen fitting, confirmed on the technical sheet rather than assumed.
3. Waste route and trap
Decide early whether the waste drops into the floor or runs back into the wall, because that decision moves the frame. The plan should show the trap type, the fall on the waste run, an access point for cleaning, and the distance from the finished wall face to the centre of the connection. This is the single most common reason a wall hung bidet ends up sitting proud of the tiles.
4. Clearances and layout neighbours
- Side clearance from the bidet centre to the adjacent fixture or wall, kept consistent with the rest of the WC suite so the row looks intentional.
- Knee space in front of the rim, checked against the finished floor build-up, including any underfloor heating screed.
- Relationship to the Wall Hung Ceramic Basin 1004B or another wall hung basin on the same wall, so heights and exposed fittings line up.
- Access to the isolation valves after tiling; they should never be sealed behind fixed tiles.
5. Suite consistency across the project
On a hotel or villa package, specify the bidet as part of a set rather than as an isolated item. Pairing it with a matched wall hung WC such as the Wall Hung Toilet 1038W, and keeping one ceramic finish and one tapware family across guest bathrooms, removes most of the visual inconsistency that shows up at handover. Where a floor-mounted option suits some rooms better, the Floor Standing Bidet 1038F covers those positions while keeping the same hygiene provision.
6. Finishes, cleaning and handover
- Tile set-out drawn so cut tiles fall behind and below the pan, not in the eye line.
- Sealant type at the wall interface, agreed with the tile supplier so it does not discolour against the glaze.
- A cleaning schedule for the buyer's facilities team that avoids abrasive products on the glossy surface.
- Spare-parts provision recorded at order stage, since replacement units arrive after the room is finished.
Quick pre-order checklist
| Item to confirm | Where it belongs in the plan |
|---|---|
| Fixing frame type and finished rim height | Wall build-up drawing, before partition close-up |
| Waste route, trap type and fall | Drainage layout, before slab or screed |
| Hot and cold outlet positions with isolation | First-fix plumbing setting-out |
| Tapware model and tap-hole arrangement | Product schedule against the technical sheet |
| Suite pairing across guest bathrooms | Sanitaryware schedule and room data sheets |
| Sealant and cleaning products | Finishes specification and handover manual |
SANTERSON supplies bathroom sanitary fixtures alongside the rest of the project package — Bathroom Sanitary Fixtures and other Interior Fixtures — with custom and OEM options, door-to-door logistics and installation support for villa and hospitality projects. Send us the room layout and we will return a setting-out sheet for the 1004F together with the matching suite.