A design brief says the master bathroom needs corner open shelving. That single line has to become a quotation, a drawing and a production order. The gap between those two things is where most custom joinery projects lose time: dimensions are assumed, finishes are described in words rather than samples, and the wall conditions behind the unit are never checked. Below is the sequence we use at SANTERSON when a brief for Santerson Corner Open Shelving arrives, and exactly what we need from you at each stage so the first quotation is the last one you wait for.
Start with the room, not the shelf
Corner open shelving in a bathroom is a built-in, made-to-measure item. It sits against two walls that meet, usually next to a basin, a shower enclosure or a doorway, and it shares those walls with pipework, waterproofing and sometimes an extraction duct. Before any shelf depth is discussed, send us the shell condition: which wall is finished, which is still open, where the waste and supply lines run, and whether the substrate can carry a fixed unit.
For a new build this information comes from the construction drawings. For a renovation it usually means photographs of the corner from both sides, plus a note on what you intend to keep. Both are acceptable; we work from whatever exists and tell you what is missing rather than guessing.
What to put in the enquiry
The items below are the ones that change a price or a lead time. Anything else can be settled later during design coordination.
| Item | What we need to see | Why it changes the outcome |
|---|---|---|
| Location and quantity | Which room, how many corners, and whether other rooms use the same detail | Repeat details are produced as one set of tooling and finishes, which keeps colour and grain consistent across the job |
| Corner geometry | Included angle of the two walls, clear height to the ceiling, and any obstruction within 300 mm of the corner | A 90° corner and an angled bay are built differently; ceiling height decides whether the unit stops short or runs full height |
| Fixing substrate | Timber stud, masonry, plasterboard, or tiled surface already in place | Determines bracket type, whether tiles need cutting, and who carries that work on site |
| Layout | Number of shelves, spacing between them, and whether the base is open, closed or sits on a plinth | Spacing drives the vertical members; a closed base hides plumbing but removes shelf-adjustment access |
| Depth and projection | Usable depth at the deep end of the corner and clearance from the basin or shower door | A corner unit projects further into the room than a straight shelf, so clearances must be checked against doors and fittings |
| Finish | Body colour, shelf material, edge treatment, and any metal hardware finish | We match finishes across cabinetry, wardrobes and vanities from one production batch |
| Use | Towels and heavy bottles, or decorative items only | Sets shelf thickness, span and bracket detail |
| Delivery terms | Destination city, port or site address, and who receives the goods | Determines packaging specification and whether door-to-door delivery applies |
If a dimension is not final, mark it as provisional on the drawing. We quote against a provisional figure, flag it, and reconfirm before cutting. What we cannot do is start production on an unconfirmed opening.
How the enquiry becomes a quotation
Our cooperation steps are fixed: project brief and design proposal, then quotation and detail confirmation, then production, shipment and follow-up. The corner shelving follows the same route as the rest of our turnkey interior project solutions, whether it is one unit for a private bathroom or the same detail repeated across a floor of guest rooms.
1. Brief review and design proposal
We read the brief against the room, then come back with questions rather than a price. Typical gaps: no ceiling line, no finish reference, no note on whether the corner is tiled. Expect this exchange to take one or two rounds; it is cheaper than a change order in the factory.
2. Specification and quotation
Once geometry and use are settled, we specify the unit: made-to-measure sizing, material and finish options, and a layout tailored to the space. The quotation follows with the specification attached, so you can see what you are approving rather than reading a single line item.
3. Production and quality control
After your confirmation the unit enters production with our own inspection at each stage. Where the shelving is part of a larger fit-out — vanities, bathroom sanitary fixtures, wardrobes or kitchen cabinetry from the same order — panels are batched together so the finishes match on site.
4. Packing, freight and handover
Units are packed for export freight, with a packing list keyed to the room they belong to. Freight moves by sea, air or rail with customs paperwork handled on our side, and door-to-door delivery is available where the site address supports it. Installation and after-sales support complete the handover.
Deciding what else goes into the corner
A corner rarely carries one function. Before the drawing is frozen, decide whether the same wall also holds a mirror light, a niche, or storage that needs to be behind a door. Related details we produce for bathrooms and living areas include:
- Niche shelving — recessed into the wall build-up, so it must be set out before tiling.
- Freestanding open shelves — no wall fixing, useful where the substrate cannot carry a load or where the arrangement may change.
- Shelving accessories — brackets, rails and lighting elements that must be ordered with the unit to match finish.
- Wall sconces — if a light sits above the shelving, its cable route has to be planned before the wall is closed up.
Where the corner sits in a kitchen rather than a bathroom, an open shelf corner cabinet is usually the better starting point, since it carries the load and closes off the dead space behind the door swing. If the wall runs to the ceiling and needs storage rather than display, corner tall cabinets cover that case; in a bedroom, shelf-focused modular wardrobes repeat the same open-shelf language behind a door.
Common reasons a corner shelving quotation stalls
- The angle is assumed to be 90°. Older properties frequently sit a degree or two off. We build to the measured angle, so send the measurement rather than the drawing intent.
- Finish named in words. "Matte oak" covers a wide range. A sample reference, a photograph of an existing panel, or a batch we have already supplied for your project pins it down.
- Tiles already fixed. A tiled wall changes the fixing detail and may require cutting. Tell us before quoting, not after delivery.
- Load not stated. Folded towels and glass bottles are heavy. If the shelf is decorative only, say so — it simplifies the build.
- No receiving contact at destination. Door-to-door delivery needs a named receiver and site access details; without them the shipment stops at the port.
Send us the brief
Santerson Corner Open Shelving is configured per project: dimensions, layout, material and finish are set from your drawings, and specifications are confirmed with you before production. If you have a floor plan, a photograph of the corner, or even just a sentence describing what the space needs to do, send it through and we will come back with the questions that matter and a specification you can price.
SANTERSON — furniture and building materials manufacturer, one-stop supply for villa, hospitality and office projects. Contact us to start an enquiry.