Why corner quotes are hard to compare

Corner units decide whether an L Shaped Corner Cabinet feels generous or cramped once the doors are on. The trouble is that two suppliers can both quote "one L corner unit, made to measure" and deliver completely different furniture. One returns a carcass you can actually reach into; the other returns a box with a shelf you have to kneel on the floor to use. Comparing samples and proposals side by side is how you find out before the containers are booked.

Start with the sample, not the price sheet

Ask every shortlisted supplier for a physical sample of what they intend to build. A door and drawer-front sample tells you about colour and edge treatment; a carcass cross-section tells you far more. Look at the panel thickness, how the edges are closed, whether the back is fixed into a groove or simply nailed on, and how the hardware is anchored into the substrate. That single cutaway answers questions no proposal line item ever will.

Handle the sample. Open and close the door on its hinges, run the drawer slide through its full travel, and press the finished face with a thumbnail. Then leave the sample in a warm, humid room for a week and look again. If an edge lifts or a front cups, you have learned it for the cost of a parcel instead of the cost of a site rectification order.

Read what the proposal actually specifies

Most corner-cabinet disputes start because a proposal describes a product rather than a specification. Before you compare numbers, make sure each quotation states the same things in writing:

  • Finished dimensions on both legs of the L, measured to the face of the cabinet and not to the back of the carcass, including any scribe or filler panel needed for out-of-plumb walls.
  • The access mechanism — pull-out carousels, a rotating Lazy Susan corner cabinet shelf set, bi-fold doors on a swing rack, or simply an open shelf. Each behaves differently once loaded.
  • Panel material and surface finish, stated by name — matte lacquer, melamine, acrylic, wood veneer — not "as per sample", unless the approved sample is numbered and attached to the quotation.
  • Hardware brands and load ratings for hinges, slides and carousel bearings, plus whether soft-close is included or optional.
  • What the price excludes: plinths, scribes, splashbacks, in-cabinet lighting, appliance housings, and on-site adjustment.

Only when all suppliers have answered these points can you compare totals honestly. A quotation that looks 15 percent cheaper often simply moved the excluded items to someone else's scope.

Compare how each supplier handles the dead corner

The geometry of an L corner wastes space in the same place every time: the wedge behind the return run. Ask each supplier to show, on a drawing, exactly what mechanism fills that wedge and how far the frontmost item sits from the cabinet opening. A pull-out tower brings everything to you; a fixed shelf hides half of it permanently. Where display matters more than capacity, an Open Shelf Corner Cabinet or a glazed unit reads lighter in a small kitchen and costs less to fit.

Also check the return leg. In a run of Custom Built-in Kitchen Cabinets, the corner unit sets the datum for everything that follows; if one supplier draws the corner 20 mm shorter than the next, your tall appliance housing at the other end of the wall no longer lines up. Ask for elevation drawings, not just a bill of quantities.

Score the proposals on the same sheet

Build one comparison table and fill it from each document. Columns: measured dimensions confirmed or assumed; access mechanism named; finish specified in writing; hardware stated with brand and rating; sample supplied and approved; drawing revision attached; exclusions listed; packing method for corner carcasses; and who carries out on-site adjustment. Score each row as yes, partial or no.

Two rows on that sheet matter more than buyers usually admit. The first is packing: a corner carcass arrives damaged far more often than a straight one, because the mitred return is the weakest point in the crate. Ask how the unit is blocked, braced and corner-protected. The second is site adjustment responsibility. Corner units meet two walls that are rarely square; someone has to scribe them on site, and the proposal should say who.

Check the supplier's coordination scope

Cabinets do not arrive alone. Worktops, appliances, tiling and electrical all interface with the corner run, so ask whether the supplier also handles adjacent interior fixtures and can coordinate them in one production and delivery plan. A manufacturer that supplies cabinetry alongside other Interior Fixtures can sequence one shipment and one installation team instead of three trades arguing over who damaged whose work.

Ask for a named contact who answers dimension queries in writing, and confirm the supplier will re-issue drawings after your site survey rather than before it. That single step prevents most corner-cabinet claims.

Approve before you order

Close the comparison with a signed approval pack: the numbered sample, the final dimensioned drawing showing the corner mechanism, and the exclusions list initialled by both sides. When two proposals look identical on price, that pack is what tells you which one will still look correct in five years.