A tall bar cabinet rarely fails because of one wrong decision. It fails because the designer and the buyer each answered a different question — the designer drew a joinery elevation, the buyer priced a cabinet — and nobody reconciled the two before production started. Aligning on six items up front removes most of the rework that appears at site handover.

1. The use case behind the elevation

Before dimensions are discussed, both sides should agree on what the unit is actually for. A dry goods store, a bottle display, a coffee and tea station and a full beverage prep point each drive different internal layouts, different services and different door types. In our catalogue these needs map to separate configurations rather than one adjustable product: Tall Bar Cabinets for full-height closed storage, Santerson Glass Front Bar Cabinets where the contents are part of the interior composition, and Santerson Integrated Bar Systems when the bar is a designed element within a larger wall.

Record that decision in writing on the drawing issue. "Bar cabinet" in a specification note is not enough for a factory to build from; state whether glass, lighting and services are included.

2. Dimensions — and which ones are fixed

Made-to-measure sizing means the unit is built to the drawing, so the two parties must agree on which dimensions carry constraints. Typical points of disagreement:

  • Floor-to-ceiling height versus a designed headroom, including skirting, cornices and any ceiling reveal.
  • Door swing and clearance against adjacent cabinetry, an island edge or a traffic route.
  • Aperture depth versus the depth of what is being stored — glassware, bottles, small appliances.
  • Whether the carcass is flush with the surrounding panelling or expressed as a separate box.

Buyers should confirm that final site dimensions are taken from the completed floor and wall finishes, not from construction drawings alone. Designers should mark which faces are visible and therefore need matched grain, edge treatment and finish continuity.

3. Materials, finish and the reference that governs

Material and finish options are broad, which is exactly where verbal agreement breaks down. The specification should name a physical reference: a signed-off sample board, a supplier code, or an approved photograph with the batch noted. Specify the substrate, the surface (matte, high gloss, lacquer, veneer, glass), the edge and handle detail, and the hardware brand or model where the designer has a preference.

Where a tall bar cabinet sits inside a run of kitchen or living joinery, both parties need to agree which element governs the finish — usually the larger visible run — and who signs the match sample before the rest of the order is released.

4. Internal layout and services

This is the section most often left open until too late. Agree the shelf positions, drawer configuration, integrated lighting, power and any plumbing before fabrication, because each affects the carcass and the site works.

ItemDesigner decidesBuyer confirms
Shelving and drawersOpen versus closed ratio, display niches, shelf heightsMade-to-measure sizing and load requirements for glass and appliances
LightingFitting type, colour temperature, switching positionDriver location and access for maintenance
Power and dataAppliance positions and outlet heightsCircuit capacity and the site electrician's scope
Glass and doorsGlass type, frame profile, hinge or sliding directionGlazing specification and hardware selection for each project

For compact rooms where a full-height unit competes with circulation, Santerson Compact Bar Cabinets and Santerson Wall Mounted Bar Units are the usual alternatives designers fall back on — decide early, because switching later changes both the joinery order and the wall works.

5. Scope of supply and the interface with site trades

State plainly what is included in the order and what stays on site: plinths, scribes to uneven walls, cornices, worktops, splashbacks, appliances, and the making-good of the wall behind. A tall unit that meets a finished ceiling needs an agreed reveal detail; without it, whoever installs first improvises.

For villa and hospitality projects where bar cabinetry is one line among many, Turnkey Interior Project Solutions place the joinery, loose furniture and finishes with a single supplier, which reduces the number of interfaces to coordinate. Where a buyer places their own order against design drawings, bespoke sizing, material and finish selection and OEM production are handled as custom furniture work.

6. Approvals, sign-off and handover

Agree the sequence before anything is cut: drawing issue, sample approval, order release, production, then delivery and installation. Both parties should know who signs each stage and what happens if a site dimension changes after release — this is the most expensive late change on built-in joinery.

At handover, walk the unit against the approved drawing: door alignment, drawer runners, lighting function, glass condition, and finish consistency under the room's own lighting. Record snags with photographs, not descriptions.

Alignment checklist to close before production: use case confirmed on the drawing · final dimensions taken from finished surfaces · signed finish sample in hand · internal layout and services resolved with the site trades · supply scope and interfaces written down · approval sequence and sign-off names agreed.

If you are specifying tall bar cabinetry for a villa or hospitality project and want an elevation reviewed against these points, send us the drawing and the room's finish schedule and we will confirm what can be built to it.