A drawer unit looks identical in two quotations and behaves very differently on site three months after handover. If you are specifying Santerson Drawer Units for a bathroom fit-out, the only reliable way to tell those two offers apart is to compare physical samples against written proposals, item by item, before you place the order.
What you are actually comparing
Santerson Drawer Units sit in the bathroom Storage Units range and are made to order: dimensions, layout, board material and surface finish are all specified per project. That flexibility is the reason two quotations can carry the same product name and still describe different pieces of joinery.
A sample tells you what a finish looks like in your lighting and how the fronts feel in daily use. The proposal tells you what will be built, where it goes, and what has to be true on site before it can be installed. Comparing one without the other is how specification gaps survive right through to the snag list.
Before you request samples: fix the scope
- Room set. How many bathrooms, and which unit type in each: a drawer unit beside the vanity, corner storage for an awkward return, or open storage in a recess.
- Opening sizes and constraints. Finished floor level, wall build-up, door swing, and the position of waste and water outlets.
- Who installs. Your contractor, or the supplier's installation support. This decides who signs off site conditions.
- Sample list. Front finish, carcass edge, worktop or counter material where relevant, plus one drawer front pulled from the actual production batch rather than a display offcut.
Send the same scope to every quotation. If the scopes differ, the prices are not comparable and no sample review will fix that.
Sample checklist: what to look for on the physical piece
- Colour and sheen under your own lighting. Check the front next to the tile, paint and counter samples you have already fixed. Matte, lacquer and veneer surfaces read differently under warm bathroom lighting than in a showroom.
- Edge treatment. Look at how the panel edges are closed on a drawer front and a shelf. Edging quality is where cheap units fail first in a humid room.
- Front flatness and grain direction. Lay the sample on a flat surface. Check that grain or pattern runs consistently across fronts that will sit side by side.
- Hardware as built, not as named. Note the slide type, how far the drawer opens, whether it closes softly, and whether the handle detail matches the drawing you were sent.
- Moisture exposure. Ask which board and finish are used in zones that will get splashed or sit near a shower enclosure, and confirm the same specification appears on the sample label.
Proposal checklist: reading the quotation line by line
Compare proposals on the same page, and treat anything missing as a cost waiting to appear later.
| Line item | What a complete entry looks like |
|---|---|
| Dimensions | Width, height and depth for each unit, with finished dimensions and tolerances, referenced to your drawings. |
| Layout | Drawer stack, shelf positions and hanging zones drawn out per unit, not "as per standard configuration". |
| Board and finish | Named board type for carcass and fronts, named finish system, and the sample reference you approved. |
| Hardware | Slide brand or specification, load rating as stated, soft-close where required, handle or handleless detail. |
| Interface items | Countertop or basin interface, cut-outs, skirting, and how the unit meets tile and plasterboard. |
| Site prerequisites | Wall strength, level and dry conditions required before installation, and who is responsible for them. |
| Commercial terms | Packaging, freight mode and delivery point, import responsibility, and what is excluded. |
| After the order | How approved samples are archived, how production deviations are reported, and the snag and spare-parts process. |
Where a proposal says "made-to-measure" or "custom", ask for the drawing that shows the measurement. Made to measure is only useful once someone has written down what it is being measured to.
Scoring the offers side by side
Score each quotation on four things, using the sample and the document together:
- Specification match. Does the drawing match the sample you approved, in material, finish and hardware?
- Completeness. Are interface items, site prerequisites and exclusions written down, or left to be discovered?
- Delivery reality. Packaging, container plan and delivery point stated for your site, not a generic freight note.
- Accountability after handover. Named process for snags, replacements and spares, with the responsible party identified.
The cheapest offer usually wins on price alone and loses on completeness. Two offers that match on specification are worth a second round of questions; two offers that do not match are not comparable at all until the gap is closed in writing.
How one supplier makes this comparison easier
When drawer units, vanities and tall storage come from one manufacturer, the sample review covers a whole set of joinery at once instead of three separate trades. Bathroom pieces are frequently specified alongside floating vanities and other fit-out joinery, so approving one finish family across the range keeps bedrooms and bathrooms visually consistent.
As a China-based furniture and building materials manufacturer working on villa, hospitality and apartment projects, SANTERSON handles design coordination, custom/OEM production, logistics and installation support under one scope, which means the same drawing set can carry storage, double vanities, cabinetry and interior fixtures rather than being split across vendors.
That single scope is also where you should concentrate your questions. Ask for the production drawing, the archived approved sample, the packaging and container plan, and the snag process, and get each in writing before you commit.
Common comparison mistakes
- Judging a finish from a photograph. Screen images flatten sheen and shift colour; approve the physical front, not the render.
- Comparing drawer counts instead of usable depth. Two units with six drawers each can hold very different loads depending on slide quality and drawer depth.
- Ignoring site conditions. A made-to-measure unit installed against a damp or out-of-square wall will fail whatever the price was.
- Treating "custom" as a specification. Custom is a method, not a description. It says nothing about the board, finish or hardware until it is written down.
Before you sign
- Every quotation covers the identical scope and unit list.
- Each approved sample is dated, labelled and referenced in the proposal.
- Drawings show finished dimensions, layout and hardware for every unit.
- Interface items and site prerequisites are written, with responsibility named.
- Freight, delivery point, exclusions and the snag process are on the page.
Work through those five points and you are no longer choosing between product names but between documented scopes. For a project enquiry about bathroom storage, vanities or wider joinery, send your drawings and unit list to SANTERSON and request the production drawing that matches the samples you approve.