A mid-century whole house custom cabinetry and built-in storage project is not one purchase but dozens of small decisions stacked on top of each other. The style itself — warm wood grain, low clean lines, curved niches, a mix of display and concealed storage — looks simple on a render. In production it depends on board choices, drawer hardware, handle details, tolerance at the wall, and how each room's joinery relates to the next. Buyers who raise these points early, in writing, usually end up with fewer site problems and a far more accurate quotation.
The list below follows the order of an actual project: what you agree on before drawings, then what you confirm before production starts. It is based on how we deliver our Mid-century Whole House Custom Cabinetry & Built-in Storage Project, where a bay window desk with storage drawers, an open staircase bookshelf and wood-grain kitchen cabinets were produced as one coordinated package.
1. Scope: which rooms are in, and what each one has to do
Start with a room-by-room brief rather than a style reference. A whole-house package typically covers the entry storage unit, living room sideboard or media wall, kitchen cabinetry, bedroom wardrobes, bay window seating and desk areas, laundry or utility tall cabinets, and staircase shelving or partitions. For each space, write down what must be stored — books, glassware, small appliances, linen, luggage, cleaning supplies — because that determines drawer counts, shelf depths and where closed doors go.
Mid-century schemes lean on a balance between open display and hidden storage. That balance should be decided per room, not applied house-wide. Open shelving beside a staircase reads well and holds books; the same openness in a kitchen next to a hob collects grease. Tell us which items you want visible and which must be out of sight, and we will split the carcasses accordingly.
2. Materials and finishes: what to specify, not just name
"Warm wood tone" is not a specification. Buyers should confirm the substrate, the surface material, and the finish separately, since each affects cost, edge treatment and how the piece ages.
| Item to confirm | Why it matters at production |
|---|---|
| Board substrate and thickness | Determines load on long shelves, hinge fixing strength and whether a door will bow across a tall span. |
| Surface: wood veneer, melamine, lacquer or acrylic | Sets the sheen level, fingerprint behaviour, edge banding appearance and cleaning routine for each room. |
| Wood colour and grain direction | Grain running vertically on a door versus horizontally on a drawer front changes the whole look; approve samples before cutting. |
| Complementary surfaces | Stone, travertine or countertop elements and any metal inlay need to be ordered against the same dimensions as the carcass. |
Our Custom Mid-century Modern Whole House Custom Furniture Project pairs warm wood grain with travertine blocks and cream wall paint, and carries hidden pull-free handles across every unit so the facades stay quiet. If you want that combination, ask for the handle detail to be drawn on the shop drawings rather than assumed from a photo.
3. Dimensions and tolerances: settle this before drawings are signed off
Built-in storage only works if it is measured against the actual building. Every dimension in a whole-house project should come from an on-site survey, not from architectural plans alone, because floor levels, wall alignment and skirting depths shift during construction. We measure precisely on site so kitchen cabinets sit correctly around appliances and a bay window desk fits the reveal it was designed for.
Confirm these with your builder or site manager before production:
- Final floor finish levels in every room, and where threshold transitions will fall.
- Positions of sockets, switches, data points, radiators and any pipework that must be boxed in or bypassed.
- Appliance schedule with model numbers and dimensions, including integrated fridge, oven, dishwasher and laundry machines.
- Door and drawer clearance against skirting, architraves, handles and each other when open.
- Ceiling heights and whether units run floor-to-ceiling with a scribe or a shadow gap.
Where a unit abuts an uneven wall, decide in advance whether you want a scribed filler, a shadow gap or an out-of-plinth reveal. That single decision changes the shop drawing and should not be improvised by an installer on site.
4. Internal fittings and hardware: the part that decides daily usability
Hardware is where a quotation can look cheap and still disappoint in use. Specify it item by item, and ask for brands or load ratings to be stated on the quotation.
- Drawers: depth, run type, soft-close, and full-extension versus partial. Deep metal drawers under a kitchen worktop hold pots properly; shallow wooden boxes do not.
- Hinges: opening angle at corners, soft-close, and whether the door is inset, overlay or flush.
- Handles: profile handles, integrated pulls or push-to-open. Handleless mid-century fronts need a routing detail drawn explicitly.
- Corner access: pull-out carousels, lazy Susan or angled shelving for corner cabinets.
- Integrated lighting: shelf or niche lighting needs a driver location, a switched or sensor circuit, and a cable route agreed with the electrician.
- Specialist fittings: pull-out laundry hampers, ironing stations, charging drawers, cutlery dividers and display shelving for glassware.
In our staircase bookshelf and partition work, vertical slat screens separate zones while still letting daylight pass. If you want a similar screen, confirm the slat spacing, the fixing method at floor and ceiling, and whether any slat doubles as a concealed access panel.
5. Design process and approvals: what to ask for in writing
A reliable supplier should hand back more than one pretty render. For a whole-house package, request space planning first, then 3D design, then dimensioned production drawings you can circulate to your builder and electrician. Our service covers site survey, 3D design, production, delivery and professional on-site installation, so the same team carries the measurements from the property into the factory.
Nominate one decision-maker on your side. Whole-house joinery stalls when colour approvals come from three people at three different times, because production cannot start on a partial sign-off.
6. Packaging, delivery and sequencing to site
For overseas projects, the customisation conversation has to include logistics. Whole-house cabinetry arrives as many separately numbered carcasses, doors and worktops, and it should arrive in the order your installer needs it. Confirm with your supplier how crates are labelled per room, what protection is used for pre-finished fronts, and whether doors travel loose or pre-hung.
As an one-stop furniture and building materials supplier, we also handle freight arrangements and door-to-door delivery, so cabinetry can be timed around flooring, painting and fixed lighting rather than landing in the middle of wet trades. Agree the delivery sequence at contract stage: built-in storage usually goes in after plasters are dry and floors are protected, but before loose furniture and final cleaning.
7. Installation, snagging and what happens afterwards
Ask who installs, and how defects are handled. Our scope includes on-site installation with inspection and snag lists at handover, plus spare parts support for hinges, runners and handles over the life of the fit-out. Response-time figures quoted in marketing should be confirmed against your actual contract before you rely on them.
Practical points to settle in the same conversation:
- Who prepares the walls, and what tolerance the installer will accept.
- Whether site protection, waste removal and making-good are included.
- What is covered for a worktop seam, a colour match or an alignment adjustment after handover.
- How replacement panels or drawer runners are ordered later, and which reference numbers to keep.
Buyer's checklist before you request a quotation
- Room-by-room storage brief with the items each space must hold.
- Appliance schedule with model numbers.
- Preferred substrate, surface material and finish for each room.
- Hardware expectations: drawer runs, hinges, handles, lighting.
- Confirmation that an on-site survey will be carried out before drawings.
- Delivery sequence, crate labelling and site access route.
- Named installer, snag process and spare-parts terms.
Materials, wood colour, sizes and storage layouts in a mid-century whole-house package can all be tailored to your floor plan and daily habits. Send us your drawings or a room list, and we will come back with a design proposal and an itemised quotation for the full cabinetry scope.
SANTERSON — China-based manufacturer and one-stop project furnishing supplier for villa, hospitality and office projects. Custom cabinetry, wardrobes, kitchen cabinets, interior fixtures and building materials, from site survey and 3D design through production, delivery and on-site installation.
Contact: PHILLIP | Phone / WhatsApp: +86-13928214007 | Email: santerson@qq.com | Enquire about whole-house custom cabinetry