A tall dining cabinet is one of the easiest pieces in a dining room to get wrong, because almost everything that matters happens before the unit reaches the site: measured openings, floor level, service runs for lighting, and an agreed sequence between the cabinet, the wall finish and the floor. The Santerson Tall Dining Cabinet is made to measure for each project, with material, finish and layout chosen per space, so an installation plan written around the actual unit rather than a catalogue item is what keeps the site programme intact.

The plan below is the one we ask buyers, contractors and interior teams to sign off before production starts. It applies to residential dining rooms, villa pantries and hospitality food-and-beverage back-of-house joinery alike.

1. A measured survey of the opening, not a nominal one

Tall units fail most often on height. A drawing may show a 2,400 mm storey height while the finished floor, plasterboard and skirting reduce the usable clear opening by tens of millimetres at different points along the wall. The survey should record:

  • Finished floor level at the front and rear of the unit footprint, measured with a laser level rather than inferred from the slab.
  • Clear width and height at head, waist and toe level, plus wall plumb and square in both directions.
  • Position of switches, sockets, radiators, downpipes and any ductwork that the carcass will pass or butt against.
  • Door and traffic clearances, so a full-height door can swing or slide without fouling a table chair or an adjacent run of cabinetry.

Because sizing is made to measure, these figures go straight into the carcass dimensions instead of being absorbed on site by packing and scribing. That is also where custom and OEM service earns its keep: a niche that is 20 mm narrower than standard, or a cabinet that has to stop short of a ceiling reveal, is resolved in the workshop drawings.

2. Carcass build, anchorage and floor loading

A full-height cabinet loaded with dinner services and glassware is heavy, and it becomes a tipping hazard if it is left free-standing. The plan must state:

  • Wall build-up behind the unit — masonry, stud and boarding, or a timber frame — and where solid blocking is required for fixings.
  • Anchor type and spacing, plus whether the unit is strapped to the wall, braced to an adjacent run, or both.
  • Whether the carcass sits on an integrated plinth, adjustable feet behind a removable toe kick, or a site-built platform, and who builds that platform.
  • Allowance for floor movement in timber-framed and new-build structures, so doors do not bind after the building settles.

If the unit is one of a matched run — a glass front dining cabinet beside it, for instance — the plan should also fix the order of assembly and how the runs are scribed to each other, so the shadow lines and hardware heights stay consistent.

3. Interior layout agreed before the doors are made

Storage that is specified after production begins gets cut on site, which is where finishes get damaged. Lock the interior down first: shelf spans and load for heavy plates, drawer versus door at waist height, dedicated deep storage for serving dishes, an open niche zone for daily use, and clear internal dimensions for anything the client intends to store — decanters, platters, a wine cooler, small appliances. Layout is specified per project on these cabinets, so this list belongs in the approval pack rather than in a site conversation.

4. Lighting and electrical first fix

Where glass fronts or lit display shelves are part of the design, the electrical rough-in has to precede the carcass, not follow it. The plan should record:

  • Lamp type and colour temperature for display shelving, and whether strips sit in a rebate or surface-mount.
  • Transformer and driver location — accessible, ventilated, and outside the sealed cabinet body where required.
  • Switch position, or the route for a sensor or remote if no wall switch is wanted.
  • Cable entry point in the carcass, and any socket inside the unit for an appliance.

For lit display work, matching the tall unit with an illuminated display cabinet keeps driver and wiring details on one specification instead of two.

5. Finish schedule and the interface with other trades

A tall cabinet reads as a wall, so its edges decide how the room looks. The plan should name the floor finish return at the toe, the plaster or panel reveal at the head, whether the unit is flush with the wall face or proud of it, and how skirting is dealt with. Record the selected material and finish from the approved sample — panel colour, surface texture, edge treatment, hardware — against a reference, so what arrives matches what was signed off.

6. Delivery route, handling and site sequence

Full-height carcasses will not turn a tight stair or a narrow lift lobby. Confirm before shipping: the delivery route from kerb to room, lift and doorway dimensions, whether panels come assembled or flat-packed for site assembly, and where the units are stored between delivery and installation. Then fix the sequence — wet trades and floor finishes complete, paint touch-up after fitting, hardware and lighting commissioning last.

For overseas projects this is also where freight planning sits: packaging and container loading, customs paperwork and door-to-door delivery are covered in logistics and door-to-door delivery, so the delivery date in the plan matches what the site programme expects.

7. Snag list and handover

Close the job with a documented check rather than a handshake: door alignment and gap consistency, drawer run and soft-close operation, anchorage confirmed, lighting working at every switch, finish free of handling damage, and internal layout as drawn. Installation and after-sales support covers on-site fitting and inspection, so the snag list is the shared document that both sides sign.

Before you order: send the measured survey, the interior layout sketch, the finish reference and the electrical rough-in drawing together. Those four documents are what turn a made-to-measure tall dining cabinet into a clean installation instead of a two-week site problem.

Plan itemWho confirms itWhen it is needed
Clear opening dimensions and FFLSite contractor / surveyorBefore production release
Wall build-up and blocking for anchorsMain contractorFirst fix
Interior storage layoutClient / design teamWith shop drawings
Lighting and cable routesElectrical contractorFirst fix, before carcass
Finish and hardware referenceDesign teamAt order confirmation
Delivery route and lift sizeBuyer / site managerBefore shipment
Snag list and sign-offInstaller / clientAt handover

If your project needs a tall dining cabinet coordinated with sideboards, display cabinets or a wider run of built-in joinery, send the drawings and we will return shop drawings and a quotation for review before anything goes into production.