A Santerson Storage & Display Combo is specified on paper long before a single panel is cut. Layout drawings, finish codes and hardware schedules all get signed off in an email thread, and then production starts. When the finished wall unit arrives on site, the two things buyers argue about most are rarely the dimensions — they are the colour of the laminate under site lighting and how the open shelves read against the closed doors. A finish sample round, done properly and done before tooling, settles both questions at a fraction of the cost of re-making a wall system.
This is especially true for configurable systems in the Media & TV Walls collection. The Santerson Storage & Display Combo listing does not carry a fixed specification: finish, layout and dimensions are set per project, and the storage configuration is confirmed for each job. That flexibility is the point of the product — and it is exactly why the sample stage matters more here than it would for a catalogue item.
Why a render is not a finish approval
3D visualisations are useful for proportion, massing and how the unit sits in the room. They are not reliable for surface appearance. A renderer applies a texture name; a press applies a real decorative paper over a real substrate with a real glue line and a real edge band. The gap between the two shows up as sheen level, grain depth and colour shift.
Treat the render as approval of intent and the physical sample as approval of execution. Nothing about the drawing stage should be read as sign-off on how the surface will look once it is installed under the lighting in the actual space.
Request the right sample set, not one convenient swatch
For a wall system that mixes open display with closed storage, one small chip is not enough. Ask for a sample pack that covers every surface family in the specification, and ask for each piece large enough to judge at normal viewing distance rather than in the hand.
- Panel bodies and door fronts. The carcass material and the door or panel material are often different products, even when they are meant to read as one colour. Request both, side by side.
- Edge banding in the same finish. A matching board colour with a mismatched edge strip is one of the most common sample-stage catches. Check the edge against the face at an angle, not only straight on.
- Glass and glazed fronts where used. Tinted, bronze or frosted glass changes character with the light behind it. Sample it against the panel finish it will sit next to.
- Metal hardware and profiles. Handleless rails, frames and any metal trim should be sampled in the same batch round as the boards, because finishes across suppliers drift.
- Worktop or shelf surfaces if they continue the design. Where a stone or engineered surface meets the cabinetry, the junction is what people notice first.
Where the specification includes integrated cabinet lighting, include that in the sample round as a decision, not a surprise. Light colour and fitting position change how a warm wood grain or a matte lacquer reads at night, and electrical specifications need confirming for each cabinet design rather than assumed from the drawing.
Judge the samples in the room they will live in
Do not approve a finish at the factory, in the showroom, or on a desk. Send the sample pack to site and fix it in position against the actual wall.
- Check it under daylight and under artificial light. North light, warm LED downlights and a feature fitting each pull a different cast out of the same surface.
- Check it against the neighbouring finishes. Flooring, wall paint or cladding, curtains and any existing joinery. A finish approved in isolation can clash the moment it is installed next to the floor covering.
- View it at distance and at an angle. Sheen and texture are judged from three metres and from a raking angle, not from ten centimetres away.
- Leave it up for a few days. Colour fatigue is real; the finish that looked safe on day one sometimes reads too cool or too yellow once it stays in view.
Confirm the configuration details while the samples are out
The sample round is the natural moment to close out the specification items that configurable systems leave open. Because dimensions, storage layout and material choices are set per project, this is when the drawing and the physical build get reconciled.
- Which modules are open display and which are closed — and how the two alternate across the elevation. The same question governs Santerson Full Height Media Walls if the wall runs floor to ceiling.
- Shelf spans and shelf fixing method, which determine whether an open shelf sags over its working life. Where the display bays need adjustable heights, note now whether you want niche shelving recessed into the carcass or open modular shelves sitting proud, because the two detail differently and sample differently.
- Door type for each closed bay — hinged or sliding — and the clearance each needs to open fully in the room.
- Cable routes, socket positions and equipment ventilation behind the media zone, agreed before panels are drilled.
- Where services sit for any integrated media storage modules, so power and data land where the drawing says they do.
If the brief calls for both display and concealment on the same wall, look at how Santerson Mixed Open & Closed Storage resolves that balance before fixing your own split. It is a useful reference point for the ratio of open to closed, and it keeps the sample round focused on one coherent material palette.
Record the approval so it survives the project
A verbal "that is the correct finish" is worth nothing eighteen months later when a replacement panel is needed. Put the sample decision on paper and keep the physical pieces.
- Photograph each signed sample next to its label and send the photo back with a written confirmation of the finish code, substrate and edge band reference.
- Have one named person approve every surface family, so the decision is not split across three consultants.
- Keep two signed samples: one for the project file, one held at the factory or with the supplier for future matching.
- Note the date and the batch round. Decorative papers and hardware are revised, and a finish re-ordered years later may not match what was installed.
What to do when two samples are too close to call
When the decision comes down to two near-identical surfaces, stop deciding on the swatch and decide on the build. Ask for a small made-up section — one open bay and one closed bay in the two finishes — so you can judge the combination rather than the material. Where the project needs a true bespoke surface rather than a catalogue option, that request fits naturally into custom furniture design and prototyping, which covers bespoke finishes and materials alongside the manufacturing route.
For projects sourcing wall systems together with flooring, wall panelling, lighting and other joinery, the sample round is easier to control when one supplier coordinates it. That is the working basis of our one-stop furniture and building materials project procurement service: finishes for the different elements come back in one pack, judged against each other once, before production starts.
A short pre-production checklist
- Every surface family sampled, including edge banding and hardware.
- Samples assessed on site, in both light conditions, against adjacent finishes.
- Open-to-closed split, door type and shelf spans confirmed against the drawing.
- Lighting, cable routes and ventilation positions agreed and marked.
- Approval recorded in writing with finish codes, plus retained signed samples.
Work through those five points and the Santerson Storage & Display Combo that arrives on site is the one you approved — not an interpretation of it. If you are specifying a wall system for a villa or hospitality project and want the sample round organised before production, send us the drawings and finish schedule and we will return a matched pack to review. Our installation and after-sales support then covers on-site fitting and inspection, so the same specification carries from the sample table through to handover.