A glass-front PVC cabinet looks simple on a rendering and complicated on site. The glazed door that makes crockery and glassware readable is also the part most likely to arrive chipped, sit out of alignment, or fog up from the wrong internal lighting choice. Because this type of unit is made to measure for each project, what happens after the order leaves the factory matters as much as the quotation. Below is the practical list of after-sales questions a buyer or procurement officer should put in writing before placing an order for a Santerson Glass Front Pvc Cabinet.

Start With What the Order Actually Confirms

The product page for this cabinet describes it as a PVC kitchen cabinet design within the PVC Kitchen Cabinet collection, offered with project-specific dimensions and finish options. The stated configuration covers made-to-measure sizing, material and finish choices, and a layout tailored to the project, with an explicit instruction to confirm dimensions and selected specifications for each order. That wording sets the baseline for every after-sales conversation: there is no single standard size or fixed specification to fall back on.

So the first question is not "what is the warranty" but "which document governs this order". Ask for a signed-off specification sheet that records the carcass and door material as ordered, the glass type and finish of the glazing frame, the hardware set, the internal lighting provision if any, and the dimensional drawing with your site dimensions on it. Any later claim about what was supplied is judged against that sheet. If your purchase order and the manufacturer's confirmation differ, get the difference resolved before production starts, not after the container ships.

Ask How Glass Is Handled in Transit

Glazed components are the most common source of claims on cabinet shipments, and the fix is agreed before loading rather than after. Concrete questions to put to the supplier:

  • Are glazed doors packed loose and labelled per unit, or fitted to the carcass for shipping? Ask which method is used and why.
  • What is the packing standard for glass panels — edge protection, corner boards, crating, and how are they positioned in the container?
  • Is each carton or crate marked with the room and unit reference from the layout drawing, so a damaged piece can be identified without opening everything?
  • Who inspects the glazing at the factory before loading, and is that inspection recorded in photos you receive?

Then agree the inspection window on your side. Counting cartons is not an inspection. Specify how many days after delivery you will open glazed items and report damage, and photograph anything questionable at the moment of unloading. A replacement request filed after installers have already fitted the units is far harder to accept, because it becomes difficult to separate a shipping defect from site handling.

Get the Replacement Terms in Writing

For made-to-measure joinery, "we will send spare parts" means little unless you know what is replaceable and how long it takes. Ask for these specifics:

  • Which items can be reordered as single pieces after the project — a glazed door leaf, a shelf, hinges, handles, an internal light strip — and which cannot.
  • What information you must supply for a replacement order: unit reference from the packing list, the dimensional drawing, or a photograph with a scale.
  • How a replacement is produced when finishes are batch-matched. Timber-look and coloured foil finishes can vary between production runs, so ask whether a replacement door is matched to the original batch or accepted as a close match.
  • Who pays freight on a replacement, and whether it travels with the next consolidated shipment or separately.
  • What happens if a unit is beyond repair — is it re-manufactured to the original approved drawing, and who signs that drawing off again?

A useful clause to request is a retained digital record: the approved layout drawing, hardware schedule, and finish codes kept against your project reference. That record is what makes a second-phase order or a hotel room refresh match the first installation.

Clarify What the Warranty Covers for Glazed and PVC Components

Warranty language on furniture and cabinetry usually separates material and workmanship faults from damage caused by handling, site conditions, or misuse. For a glass-front PVC cabinet specifically, ask where these sit:

  • Seal integrity on the glazing frame and whether moisture ingress between the panel and frame is covered.
  • Edge banding or foil wrap on PVC-wrapped panels lifting near a heat source, and what clearances to ovens and hobs are required for that reason.
  • Hinge and slide mechanisms — the supplier's own hardware versus a branded fitting, which may carry its own terms.
  • Internal lighting drivers and transformers, which often fail before the strip itself and may be excluded from the cabinet warranty.

Also ask what voids cover: cleaning agents on glazed panels, over-tightening of hinges during site adjustment, and cutting a unit to fit on site. Get the recommended cleaning and maintenance instructions for both the glass and the PVC surface in writing, since these are the instructions your client's facilities team will follow.

Installation Support Decides Whether After-Sales Is Ever Needed

Installation and after-sales support are part of the service scope SANTERSON lists, alongside logistics and door-to-door delivery, so the question is how far that support extends on your project. Establish early whether installers or a supervisor attend site, whether alignment and door adjustment are included, and whether a snag list is produced jointly at handover with target dates for closing each item. Glazed doors show misalignment more clearly than solid doors, so a joint snag inspection is worth arranging deliberately.

If your own trades fit the units, ask for an assembly instruction set specific to glazed doors — the correct order of fitting glass before or after hanging, the torque setting for hinges on a loaded glass leaf, and whether two people are required per door. Getting this wrong is the most common cause of a cabinet that looks fine on day one and sags by month six.

Before you order, ask what happens if site dimensions change after production has started. Made-to-measure joinery with glazed doors cannot be trimmed on site without losing the warranty on that unit, so the change procedure — cut-off date for drawing revisions and the cost of a late revision — should be agreed in the contract.

Plan for the Life of the Project, Not Just Handover

Hotels, serviced apartments and villa developments replace or extend joinery years after the original order. Two questions protect that future: can the supplier keep your specification on file long enough to reorder an identical door, and are discontinued finishes flagged before you commit rather than after a component fails? Ask also whether the hinges and slides are standard catalogue items you can source locally if a replacement is needed urgently.

For multi-unit work such as guest-room kitchens or apartment blocks, request that one complete set be signed off as an approved reference unit and stored. That sample becomes the benchmark for every later batch and removes most disputes about colour, glazing tint and door alignment.

A Short Pre-Order Checklist

Confirm before production starts

  • Approved specification sheet, dimensional drawing and finish codes on file for every unit.
  • Written packing method for glazed doors and panels, with pre-loading inspection photos.
  • Defined inspection window after delivery, and how damage must be reported and photographed.
  • Named list of reorderable spare components, plus freight responsibility for replacements.
  • Warranty scope separated for panels, glazing frame, hardware and lighting, with what voids it.
  • Cleaning and maintenance instructions for glass and PVC surfaces supplied in writing.
  • Installation responsibility, snag list process, and handover sign-off recorded on site.
  • Long-term record retention so later phases can be matched to the original order.

SANTERSON works as a one-stop furniture and building materials supplier, covering design coordination, custom and OEM production, logistics and door-to-door delivery, then installation and after-sales support. If you are specifying glass-front cabinetry for a villa, apartment or hospitality project, send the layout drawings and finish preferences with your enquiry so the specification, packing method and after-sales terms can be confirmed in writing before production is scheduled. Use the SANTERSON contact page to start that conversation.