A spa that is not square rarely fails in the factory. It stalls in the approval chain. Once a shell moves beyond standard geometry and becomes a site-specific shape, everyone on the project — architect, landscape designer, builder, procurement lead, operations team and owner — is asked to sign off on something that does not appear on any catalogue page. Below is how we run those approvals on customizable shape outdoor spa orders, so the plan is agreed before tooling starts instead of being argued over on site weeks before handover.
Who signs, and what each signature actually covers
On a villa or hospitality project the approval chain normally runs through five roles. Overlook one of them and you get a change order after production has already begun.
- Architect or design lead — footprint, alignment with terrace lines and setbacks, sightlines, drainage direction, maintenance access.
- Landscape designer — coping material, deck interface, planting proximity, how the spa reads against surrounding paving and outdoor furniture.
- Builder or site contractor — slab and sub-base preparation, waterproofing, electrical routing, plant location, lifting and access for delivery.
- Owner or operator representative — usable depth, seating layout, jet positions, water features, lighting, cover and cleaning routine.
- Procurement or project manager — budget ceiling, approval dates, delivery window, and the point after which shape changes carry a cost.
Our task as manufacturer is to hand each of these people something they can genuinely approve. A rendering is not that thing. What works is a drawing pack with dimensions, sections and an equipment schedule, released in stages.
Stage 1 — Site constraints before any talk of shape
The most common error on a personalized hydrotherapy pool is opening the conversation with "we want an oval". Shape should be fixed last, because everything else constrains it. Before we draw anything we ask the project team for:
- a dimensioned terrace or garden plan, including parapets, columns, steps and existing planting;
- the intended sub-base — ground slab, suspended slab, deck on bearers, or podium structure;
- available electrical supply, and where plant and control equipment can sit;
- the access route from street to installation position, including gate widths and overhead clearance;
- who carries out waterproofing, tiling or coping around the shell, and who owns the joint between them.
This stage produces a constraint sheet, not a design. Builder and design lead sign it together, which prevents the dispute that follows: the spa fits the drawing but not the slab.
Stage 2 — Shape options drawn to real geometry
With constraints on paper we return two or three shape options rather than one. Our outdoor spa shells are made in acrylic with balanced structural reinforcement, which is what makes square, round, oval and curved plans feasible at all. Each option comes back as a scaled plan with overall outer dimensions, an inner water-line dimension, seating positions marked and the depth profile noted.
Two factors decide approvals here:
- Curved plans are priced by their curves. A single sweeping radius is straightforward. A free-form plan with several reversing radii adds forming work and makes the coping harder to fabricate. We state this in the option comparison so the client chooses knowingly rather than discovering it at quotation two.
- Reinforcement follows geometry. The reinforcement layout has to suit the chosen plan, which is why a curved shape cannot be altered after tooling without being re-checked structurally.
The client signs one option. The architect countersigns that it sits inside the agreed footprint. From this point the shape is frozen and everything after it is detail, not form.
Stage 3 — How the spa meets the deck
This is where custom shapes earn their difficult reputation, and one drawing removes almost all of it. The junction between shell, substructure, coping and finish has to be settled on paper before anyone orders stone.
| Interface | Who decides | What the approval drawing must show |
|---|---|---|
| Shell to sub-base | Builder, with our structural note | Bearing line, support perimeter, access void for plant |
| Shell to coping | Landscape designer and stone supplier | Coping width, overhang, fall away from the rim |
| Spa to decking | Architect | Expansion joint position, finish level, drainage route |
| Plant and controls | Electrical contractor with us | Equipment positions, isolation points, service access |
We ask for a single combined signature on this pack. When the landscape designer and the stone supplier approve the same drawing, curved coping is ordered once instead of twice.
Stage 4 — Water experience sign-off
Owners rarely read dimensioned plans; they judge how the water behaves. For the hydrotherapy side we put the following on a one-page schedule for approval: jet positions set against the seating layout, whether a swim-training unit is wanted along the long axis, waterfall or water-column features, underwater lighting colour and control, sanitation approach, and heating arrangement.
Where a brief asks for both exercise and soaking, an outdoor swim spa with hydrotherapy and relaxation zones is often the more efficient plan than one open pool — the long channel takes the laps, the quieter end takes the jets. Where the brief is purely relaxation on a smaller terrace, a round outdoor hot tub spa with hydrotherapy jets usually approves faster, because there is less interface detailing around it.
Equipment schedules separate what is included in the quoted configuration from what remains optional. Settling that at sign-off rather than at commissioning is the single largest saving on a custom spa project.
Stage 5 — The approval log
Every custom shape order carries a short approval log: date, item approved, who signed, what changed since the previous version. It is not bureaucracy. It is the document that resolves "I thought the depth was different" without halting production while people reconstruct history from emails.
The log follows the sequence our project work normally runs — brief and design proposal, quotation and detail confirmation, then production, shipment and follow-up — with one addition for custom spas: a hard cut-off date after which geometry changes are quoted separately. Every stakeholder sees that date before they approve Stage 2.
Rules that keep approvals moving
- Name one decision-maker per discipline at kickoff. Two architects with opinions on the same radius will cost a fortnight.
- Set review dates by working backwards from the production start date, not forwards from today.
- Issue plans in metric with a tolerance note; coping suppliers need to know what can be adjusted on site.
- Never approve a curved plan on a rendering alone. It must carry dimensions.
- Confirm electrical supply and service access before the shape is finalised. Plant access is the constraint most often found too late.
- Approve the spa alongside the surrounding outdoor furniture layout, so loungers, shade and circulation are signed off as one zone rather than as separate purchases.
Where we fit into this
SANTERSON has manufactured furniture and building materials in China since 2008, supplying villa, hospitality and office projects with custom products produced under our own roof — which is why a non-standard spa plan can go from drawing to shell without an intermediary re-quoting it at every step. Our project work covers design coordination, custom and OEM production, door-to-door logistics, installation support and after-sales service, so the team that drew your shape is the team that answers when the site asks about the coping junction.
Send us a terrace plan and the shape you have in mind. We will return two or three feasible options, dimensioned, with the reinforcement and equipment implications already marked — so your stakeholders approve something buildable rather than an idea.