A quotation for Santerson Glass Front Dining Cabinets usually arrives as a PDF with an elevation drawing, a finish code and a price. Two suppliers can send drawings that look almost identical and still produce very different cabinets on site. The difference is decided by what the paperwork actually pins down — and by what it quietly leaves open.
Because these cabinets are made to measure rather than picked from a catalogue, the proposal is the contract for the finished item. Before you compare prices, here is how to read one properly.
Start with what a made-to-measure proposal has to state
The product page for this line describes three configurable points: made-to-measure sizing, material and finish options, and a layout tailored to the project. Treat those as a checklist. A proposal that answers all three can be compared with another supplier’s on price. A proposal that leaves any of them open is not yet comparable — it is an estimate.
The practical test is simple: could a different workshop build the same cabinet from this document without calling you? If the answer is no, something in the drawing or specification has to be resolved first, and that gap will surface later as a variation.
Check 1 — Dimensions tied to your site condition
Ask where each number came from. A width taken from a set-out drawing is not the same as a width measured on site after the flooring, skirting and plasterboard are finished. Glass-front dining cabinets usually sit against a wall run that includes switches, power points, archheads or an uneven old wall, and those details change both carcass width and door swing.
- Overall height, width and depth stated as finished dimensions, with the reference line they are measured from.
- A note on which site works must be complete before the cabinet is templated or manufactured.
- Clearances for door swing and drawer pull-out shown on the plan, not assumed.
Terminology varies by region: “joinery”, “cabinetry” and “built-in furniture” are used interchangeably for this product type. Ask the supplier which they mean, because it decides who supplies the carcass, the doors and the installation.
Check 2 — The glass specification, in writing
The visible part of this product is the glass, so it should be the most specific line in the document. Suppliers commonly write “glass front” and leave everything else to habit. Push for the details, because tint and treatment are what you see every day from the dining room.
| Item | What to look for in the proposal |
|---|---|
| Glass type | Tempered or laminated safety glass, stated explicitly. “Safety glass” alone is too vague. |
| Tint and tone | Clear, bronze, grey, frosted or ribbed. Names vary between workshops, so ask for a physical sample before you sign off. |
| Thickness | A figure in millimetres for the infill panel. |
| Edge treatment | Polished, seamed or painted edges, and whether the edge is visible from the room side. |
| Pattern and division | Mullion positions, glazing bead style, and whether the glass divides in line with the doors below it. |
| Handle and hardware | Model or drawing reference for hinges, handles and any door mechanism, plus who supplies them. |
Check 3 — Carcass, interior and finish continuity
The cabinet body has to match the rest of the joinery in the room. A proposal that specifies only the door front leaves the carcass, interior and edges to whoever builds it. Ask for the substrate, the panel thickness, edge banding or paint treatment, and the interior fitout — shelf heights, glass shelves versus timber shelves, drawer configuration and any cutlery or stemware provision.
If the dining cabinetry is part of a wider package, ask how the finish is matched across pieces. A tall dining cabinet or a wall-mounted sideboard in the same room reads badly when the veneer or lacquer tone drifts. The matching method — same batch, same production run, same lacquer code — should appear in the specification.
Check 4 — Lighting and electrical coordination
Glass-front cabinets are usually specified with internal lighting, and this is where drawings most often contradict the site. If lights are shown on the elevation, ask who supplies them, where the driver sits, how it stays accessible for service, and which trades run the cable and the switch. Where integrated lighting is part of the package, confirm electrical ratings and compatibility for your configuration before the carcass goes into production.
Check 5 — The commercial fine print
- Inclusions: is delivery, installation or site supervision priced in, or quoted as a separate line later?
- Freight basis: which Incoterms apply, and who handles customs clearance at the destination.
- Packaging: how glazed doors and glass shelves are packed for ocean freight, and how spare panels travel.
- Approval sequence: what you sign off — shop drawing, finish sample, or both — and the cut-off after which dimensions are frozen.
- Change handling: how a late site change is priced, since glass has a longer lead time than the carcass.
Check 6 — How one supplier covers the whole scope
Dining cabinetry rarely stops at one item. When the fitout continues into display shelving, the same workshop should be able to carry the language through — for example glass front display cabinets in an adjoining wall, with matching glass tint and hardware. Coordinating those pieces with one manufacturer reduces the risk of two sets of tolerances meeting on one wall.
SANTERSON is a China-based furniture and building materials manufacturer working on villa, hospitality and office projects, with services that run from design coordination through production to door-to-door logistics and installation support. For a buyer, that scope means one point of accountability for drawings, finishes and delivery — which is exactly what makes a proposal assessable in the first place.
A five-minute red-flag scan
- No finished dimensions with a stated reference point.
- “Glass” without type, thickness or tint named.
- Carcass and interior described as “standard”.
- Lighting drawn but not specified or priced.
- Finish matched by description (“natural oak effect”) rather than a sample or code.
- Delivery, installation and after-sales absent from the document.
Before you sign
Send one short email back to the supplier listing the six checks above and ask them to confirm each in writing. What comes back tells you as much about the build as the price did. A manufacturer who answers precisely, offers a physical glass and finish sample, and states the approval cut-off is telling you the process will hold on site. Vague replies at proposal stage almost always become variations later.
If you are assessing cabinetry for a villa or hospitality project, send us the drawing set and we will confirm sizing, glass specification and finish options for your configuration before production starts. Enquiries: SANTERSON contact.