A wood grain PVC cabinet order rarely stalls at the design stage. It stalls in production, when a door that looked warm and low-sheen on a screen arrives with a shallower emboss, a joint detail nobody drew or an edge treatment nobody chose. If you are specifying cabinets for a villa kitchen, an apartment fit-out or a serviced-apartment unit, the working list below is what we ask buyers to settle before a board is cut.

1. Core construction: substrate, door profile and carcass

Ask for three items in writing, because "PVC cabinet" describes the surface wrapping, not what sits underneath it. In our custom and OEM service, each one is a separate line on the quotation detail sheet: the panel substrate; the door profile and its radius; the carcass and back-panel specification. The product listings state made-to-measure sizing, material and finish options and a layout tailored to the project, so name your preference for all three instead of accepting a default build.

Two quotations can both read "PVC cabinet, 18 mm" and still not be comparable. Ask for substrate name and board thickness for doors, carcass and back panels separately, and the comparison becomes possible.

2. The wood grain itself: pattern direction, emboss and sheen

This is where a matte PVC cabinet front diverges furthest from solid timber, and where an approved sample earns its freight cost. Four things need specifying: the grain pattern reference; whether the grain runs vertically or horizontally across each door; whether the surface is smooth or wood-textured embossed; and the sheen level. Then check how the same film behaves over a rebate, a grooved shaker rail or a rounded profile. Wrapping softens the grain line, and raking light will show it.

Approve a full-size wrapped door, not a film offcut, and photograph it under both daylight and warm LED before sign-off. Grain direction is the detail most often left unstated and most visible once a row of doors is installed.

3. Edge treatment on doors and panels

Wrapped edges, edge banding and mitred returns look different up close and price differently. Decide which applies to door fronts, visible carcass edges, shelf fronts and returned end panels, then show it on the drawing. If you want a mitre, say so. An unmitred wrapped edge is a normal default, not a fault.

4. Hardware, load ratings and opening geometry

Confirm hinge brand and closing action, drawer runner type and load rating, handle or handleless profile, and the door layout on tall units. Then cross-check the clearances: a 600 mm double-door unit with an internal pull-out tray needs side room for the runners, and an appliance housing needs its ventilation gap drawn rather than assumed on site.

Have every hardware item listed by model number in the quotation. A substitution accepted at order stage is straightforward; the same change after production starts is not.

5. Verified dimensions, site tolerances and interfaces

Our custom kitchen cabinets for residential and hotel projects are made to measure, which puts the responsibility for verified dimensions on whoever records them. Settle finished floor levels, wall straightness, skirting treatment, ceiling or cornice heights, and the exact interface with worktops, splashbacks, tiling and appliances. Scribe gaps, filler panels and returns belong on the drawing rather than in the installer's judgement on the day.

6. Matching the tone across the rest of the joinery

Where cabinets sit beside wardrobes, media walls or panelling, confirm the wood grain repeats across those items too. A wood grain melamine cabinet and a wrapped PVC front in a nominally similar oak will not read as one set unless the film or board reference is matched on purpose. If gloss surfaces appear nearby, view them against high gloss wood effect cabinets in the same room light before committing.

7. Packaging, delivery and receiving at site

Wrapped doors and assembled carcasses travel differently, so confirm panel orientation in the crate, corner protection, and a packing list keyed to the unit numbers on your drawing. If the site takes deliveries in stages, ask for container loading to follow the installation sequence. Our logistics and door-to-door delivery service arranges freight and shipping paperwork; customs clearance and last-mile handling at your address still need agreeing in writing, together with Incoterms.

8. Quality checkpoints before shipment

Agree the checkpoints before production opens: the approved sample kept to hand, first-article doors photographed against that reference, colour and emboss read under both light sources, a function test on each drawer type, and an inspection record packed with the units. Set out at the same time how a discrepancy is raised and settled, and what installation and after-sales support covers, spare panels included. Those cost far less while the reference batch is still running.

Before you release the order: six confirmations on one drawing

Send your layout and expect a marked-up detail drawing back showing substrate, door profile, film reference, edge treatment, hardware models and verified dimensions. If one of those six is missing, the job is not ready for production. That single sheet is the difference between the finish you specified and the cabinets that turn up.