A minimalist black frame wardrobes submittal is the document set a contractor, designer or project owner reviews before approving the joinery for manufacture. It records what will actually be built: the opening dimensions, the frame and infill specification, the internal layout, the hardware and the coordination details that keep a slim black aluminium profile reading crisp once it is on site. A submittal that answers these questions up front removes most of the back-and-forth between the design team and the factory.
1. Drawings That Match the Room, Not the Catalogue
Our built-in wardrobes are made to measure for each project, so the first item in the pack is a dimensioned drawing of the specific opening — overall width, height and depth, plus the floor, ceiling and adjacent wall conditions. We supply elevation drawings for every run, a plan view where the wardrobe turns a corner or meets a door swing, and setting-out dimensions relative to fixed site reference lines.
For a minimalist black frame detail this is where problems are usually caught. The drawing should show the finished floor level, whether the unit is scribed or packed to the wall, how the profile resolves at an unlevel ceiling, and how skirting, cornice or niche panelling is dealt with around the frame. A single section through the head and one through the base tell the reviewer more than a rendered perspective.
2. Frame Profile and Infill Schedule
The visual character of the wardrobe sits in two decisions: the aluminium profile and the panel inside it. The submittal should list, for every door and fixed panel, the frame colour and surface treatment, the infill material, the infill thickness and the edge detail. Glass, acrylic, lacquer, veneer and solid panel infills all behave differently in a slim black frame, so the schedule needs to state which one applies where rather than leaving it to a general note.
We work through the same family of finishes across the wider built-in furniture range, so a bedroom wardrobe, a tall cabinet and a media wall can be specified to one consistent black frame detail. If the infill is glass, record the glass type and whether the surface is clear, frosted, ribbed or tinted, and confirm which side faces out.
3. Door Type, Hardware and Operating Clearances
State the door type — hinged, sliding or open — and then everything that makes it work: hinge brand and model, slide system and load rating, soft-close provision, handle or handleless detail, and the pull clearance each door needs. For sliding door wardrobes, the submittal must show the track position, the overlap between leaves and the recess or face-fix arrangement, because a black frame sliding detail fails visually when the leaf overlap is left to the installer.
Include a hardware schedule with quantities, a note on load capacity for hanging rails and drawers, and the door weights if they approach the hardware limit. Where a handleless profile is specified, show the finger pull or push mechanism in section.
4. Internal Layout and Storage Zoning
The internal layout is approved once, with the submittal, so it should be drawn rather than described. We provide hanging zones, drawer banks, shelf spacing, shoe and accessory storage, lighting provisions and any mirror or glass shelf detail, dimensioned for each compartment. Where a walk-in arrangement is part of the scheme — an island walk in wardrobe or an L-shaped run — the plan should show circulation width and the relationship between opposing runs.
Confirm shelf span and thickness against the intended load, and note where adjustable shelves are used so that a reviewer can see what may be reconfigured later without affecting the carcass.
5. Materials, Finishes and Sample Sign-Off
List the board material, the substrate, the surface finish and the edge treatment for every component type, and attach physical samples: a black frame corner sample showing the profile and its joint, plus infill samples in the approved finish. A sample reference number on the drawing that matches the sample tag on site prevents a colour substitution during production.
For hotel and apartment work, this is also where the wear and cleaning expectation is recorded — which finishes are intended for high-frequency use and which are decorative only. We specify materials for long-term residential and commercial use, but the reviewer should still see the finish choice tied to the room type.
6. Site Conditions, Tolerances and Interfaces
A black frame shows every misalignment, so the submittal should record the site conditions assumed at design stage: floor flatness, wall plumb, allowable tolerance, and how the unit is packed or scribed. It should also show interfaces with flooring, skirting, wall panelling, lighting circuits and any adjacent minimalist black aluminum frame cabinets in an open-plan scheme, so that reveals and shadow gaps line up across trades.
7. Manufacturing, Packing and Installation Information
Close the pack with the information procurement needs to place and receive the order: unit numbers matching the drawings, a bill of quantities, packing and labelling schedule, container or pallet arrangement, and the installation sequence with fixing details for the wall type on site. We handle production coordination through to door-to-door delivery and on-site installation guidance, so the submittal can also state who fixes, who supplies the fixings and what needs to be prepared before the wardrobes arrive.
Add an approval sheet with space for the consultant, contractor and client signatures, and a revision table. Any change to frame colour, infill, door type or internal layout after approval should be reissued as a numbered revision rather than absorbed into site correspondence.
A Short Pre-Submission Checklist
- Dimensioned elevations and plan for every run, tied to site reference lines
- Head, base and reveal sections showing the black frame resolution
- Frame and infill schedule with finish references matching physical samples
- Hardware schedule with door weights, pull clearances and track or hinge positions
- Internal layout drawn to dimension, with shelf spans confirmed
- Site tolerance assumptions and interface details for flooring, panelling and lighting
- Unit numbering, bill of quantities, packing schedule and installation sequence
- Signed approval sheet with a revision table
If you are preparing a submittal for an apartment, villa or hotel bedroom package, send us the room drawings and the finish direction you are working to. We will return dimensioned shop drawings, a frame and infill schedule with samples, and a quotation built on that specification — so what is approved on paper is what arrives on site.