Ribbed glass wardrobe doors look simple on a mood board and complicated on a purchase order. The vertical reeded pattern diffuses light, softens the view of what sits behind the door and reads as a design feature rather than storage furniture — which is exactly why it gets specified late and documented loosely. Procurement teams who have ordered flat glass panels before often carry the same paperwork across, then discover that fluted glazing changes what has to be recorded: panel orientation, reveal direction, frame interface, hardware set, and how a made-to-measure unit is dimensioned on site.

This guide sets out the record a buyer should build before a ribbed glass wardrobe enters production, and why each line item prevents a specific failure on site. It is written for purchasing managers, project buyers and main contractors coordinating built-in furniture in villas, serviced apartments and hospitality guest rooms.

Start With the Room Record, Not the Door Specification

Wardrobes in this category are made to measure. Nothing on the order can be finalised before the opening has been recorded against the finished floor and finished ceiling levels, because reeded glass panels are cut to size, framed to size, and set into tracks or hinges that have almost no tolerance for a wall that is out of plumb.

Before any glazing decision is made, capture the following for each wardrobe position:

  • Room identification and wardrobe reference number, matched to the drawing set so the same code appears on drawings, the bill of quantities, the packing list and the delivery note.
  • Width, height and depth measured at three points — top, middle, bottom for width; left, centre, right for height — with the smallest dimension noted alongside the nominal one.
  • Finished floor level and finished ceiling level, stated explicitly. A wardrobe ordered against a structural slab rather than the completed floor arrives short or proud.
  • Wall plumb and square readings, plus written confirmation of which walls are in contact with the carcass and whether those walls are plasterboard, masonry or an existing lined surface.
  • Positions of skirting, architraves, light switches, thermostat heads, sprinkler heads and ceiling recessed fittings within the wardrobe envelope.
  • Adjacent trade interfaces: where the flooring stops, where electrical containment terminates, whether a lighting strip is required inside the carcass and who supplies it.
Record measurements on a dated, signed site sheet with the surveyor's name. When a unit does not fit, the difference between an expensive remake and a resolved snag is usually a documented measurement record rather than an email thread.

Document What "Ribbed" Actually Means on the Order

Reeded, fluted, ribbed and reeded-flute are used interchangeably in catalogues and mean different physical products. Two panels can both be called ribbed while differing in flute pitch, flute depth, whether the pattern sits on the outer or inner face, and whether the glass is clear, low-iron, bronze, grey or frosted beneath the pattern. A purchase order that says only "ribbed glass" cannot be compared between suppliers.

For every door and side panel, write down:

ItemWhat to recordWhy it fails if omitted
Pattern faceWhich face carries the flutes — room side or wardrobe interior sideReversed glazing changes reflections, and cleaning access to the grooves
Flute directionVertical or horizontal, with a marked sample fixed to the orderA horizontal flute on a tall door reads as an error even when it is ordered correctly
Glass tint and clarityClear, low-iron, bronze, grey or frosted base glass, stated by nameBronze and grey tints shift colour noticeably once the panel is backlit by a window
Panel thicknessNominal thickness of the glazing as it enters the frame channelFrame channels and hardware are matched to a thickness range, not to a look
Edge treatmentSeamed, polished or seamed-and-polished edges on visible panel bordersReeded glass with unfinished visible edges is commonly rejected at handover
Safety requirementWhether tempered, laminated or tempered-and-laminated glazing is required by the project specificationRe-cutting toughened glass is not possible; a wrong spec means a full remake
Approved sample referenceSample code, date approved and who approved itColour and pattern disputes are settled by the signed physical sample

Keep a physical or high-resolution photographed sample of the exact reeded panel with the order file. Photographed samples should be shot in daylight against a neutral background, because reeded glass changes appearance completely under warm artificial light.

Fix the Door System and Frame Interface Early

Ribbed glazing is a door face, not a wardrobe. The operating system behind it — sliding, hinged or an open walk-in arrangement with glazed partitions — determines the track load, the number of panels, the overlap, and whether the pattern reads as continuous across the front.

Where the plan shows doors that run in a track, glass sliding door wardrobes require documentation of the track length, the number of panels and stiles, the panel overlap at the closing stile, and the clearance needed for the doors to pass each other. Where hinged doors are used instead, record hinge type, hinge count per door, door weight class, and the opening sweep against beds, doors and bathroom entrances.

Frame detail also matters more with reeded glass than with a plain painted panel. Record whether the glazing is framed in an aluminium or timber border, the visible width of that border, and the colour or finish of the frame — for example a slim black frame against fluted glass, or a bronze-toned frame that picks up the tint of the glass. Frameless reeded doors need a written detail for the top track, bottom guide and any patch fittings, because there is no border to absorb a cutting tolerance.

Specify the Interior Layout Separately From the Front

A common procurement mistake is treating the wardrobe as one line item. The front is a glazing and joinery decision; the interior is a storage planning decision with its own dimensions, quantities and change history. Document them on separate schedules that reference the same wardrobe number.

  • Hanging zones: single or double hanging rails, rail length, and rail height for each zone.
  • Shelf stack: number of shelves, shelf spacing, and whether any shelf is adjustable or fixed.
  • Drawer bank: number of drawers, drawer type, and whether the front matches the glazed door or the carcass.
  • Specialist items: shoe shelving, trouser pull-out, jewellery tray, valet rod, integrated lighting, soft-close fittings.
  • Carcass material and finish, back panel thickness, and whether the unit is scribed to an uneven wall or installed with a face reveal.

Where a project mixes wardrobe types across room types — for instance glazed doors in master bedrooms and open or modular systems in second bedrooms — keep one schedule per type so that quantities, finishes and hardware sets stay traceable. Comparing the frosted glass wardrobe option against reeded glazing in the same table is useful when a designer wants privacy with a similar light quality, since both diffuse the view of stored clothing but differ in how much detail they hide.

Write Down the Verification Steps Before Production

Made-to-measure built-in furniture has one cheap checkpoint and one very expensive one. The cheap one is a pre-production confirmation pack; the expensive one is site delivery. Require, in writing, that the following are returned for approval before cutting starts:

  • Shop drawings at each wardrobe position, with overall dimensions, panel sizes, door split and hardware positions.
  • A glazing schedule listing every ribbed panel by size, thickness, tint, pattern face and safety spec.
  • A finishes schedule naming carcass, door frame, internal and hardware finishes with reference codes.
  • Confirmation that on-site dimensions were re-taken after the flooring, plastering and ceiling trades completed.
  • Packing and crate marks matched to room references, so a site team can place each crate in the correct room instead of opening everything in the lobby.

For projects where the wardrobe is one package among many built-in items, this confirmation pack is also the point at which custom and OEM requirements are locked — bespoke finishes, texture and hardware substitutions should be recorded as approved deviations with a date and an approver, not left in correspondence.

Plan Delivery, Handling and Installation Records

Glazed doors are the breakage risk in the shipment. Document the packaging standard for reeded panels — edge protection, glazing tape or film, interleaving, crate orientation markings and "fragile glazing" labelling — and record who inspects each crate on arrival and what happens when a panel is found damaged.

For international orders, the buyer's file should also hold the shipping documents that let goods clear without delay: commercial invoice, packing list with crate marks, transport document and any origin documentation required by the importing country. State the delivery term and who is responsible for the last leg to the apartment or villa floor, since glazed panels frequently cannot pass through a service lift and need a manual carry.

At handover, record the installation items that get argued about later: which rooms were completed and signed off, snags raised against glazing and frames, spare parts issued such as replacement rollers, tracks, handles and one spare panel per wardrobe type where the project allows it, and the contact route for warranty claims with the purchase order number attached.

Frequently Asked Questions

Should ribbed glass be specified on the inside or outside face of the door?

It depends on the design intent and the frame system. Record the face explicitly on the order and on the shop drawing, because reversing the glazing changes both appearance and how easily the grooves can be cleaned.

Can reeded glass panels be cut down on site to fit?

No. Toughened and laminated glazing cannot be re-cut after manufacture, and the pattern position relative to the panel edge is fixed once the panel is made. This is why the dimension record must be taken after the finishing trades have completed.

Do ribbed glass wardrobes suit small bedrooms?

They usually work well where a fully clear glass front would expose stored clothing, because the flutes hide shape while still reflecting daylight. The decision is about how much visual noise a project can accept, so it should be made against a sample in the actual room.

What single document most often gets skipped?

The glazing schedule. Wardrobe orders routinely describe the door finish in words and never list panel sizes, thickness, tint and safety spec — the four fields a supplier needs to quote accurately and the four fields a buyer needs when something arrives wrong.

Putting It Together

A ribbed glass wardrobe order is defensible when five documents exist and agree with each other: the site measurement record, the glazing schedule, the door and frame detail, the interior layout schedule, and the pre-production confirmation pack. Build those before production starts and the expensive arguments move from site to the desk, where they are cheap to settle.

SANTERSON manufactures built-in wardrobes and other fitted furniture for villa, apartment and hospitality projects, with made-to-measure sizing, selectable materials and finishes, layouts tailored to each project, and support across production, door-to-door delivery, installation and after-sales. Send the room schedule and the glazing requirements for a quotation against your own drawings.