A glass-front bookshelf looks simple on a drawing until the first shelf height, door hinge and light fitting have to be decided. For residential living projects, Santerson Glass Front Bookshelves are supplied as configurable built-in units: made-to-measure sizing, material and finish options, and a layout tailored to the room. The list below is what we ask buyers, designers and contractors to settle before an order is placed, so that what arrives on site matches what was drawn.

1. Dimensions: the wall first, then the unit

Glass-front units are usually specified as built-in furniture, so we start from a measured opening rather than a catalogue width. Please send us the overall width and height of the wall, the depth you want to keep in the circulation space, and where the room runs out of plumb or has skirting, architraves, radiators or switches in the way.

  • Overall width, height and carcass depth, plus whether the unit stops below the ceiling or is taken up to it.
  • The position of sockets, switches, air diffusers and curtain lines that the carcass has to avoid or sit around.
  • Floor level across the wall. On long walls we check the deviation so the plinth and toe-kick can be scribed on site instead of cut back later.
  • Access route and lift or stair dimensions, because a full-height glazed unit is handled differently from a knocked-down carcass.

2. Interior layout: what actually goes on the shelves

Tell us what the shelves will hold — books, display objects, binders, ceramics or a mix. That single answer sets shelf spans, shelf depths and load handling. Long spans loaded with hardbacks behave differently from shallow display niches, and adjustable shelving only works if there is room for the pitch to move.

  • Fixed or adjustable shelf positions, and the pitch you want between them.
  • Open display bays combined with closed lower cupboards — a mix we build into the same run so heavy storage stays near the floor.
  • Integrated media or work surfaces in the same wall. If the bookshelf shares a wall with Santerson Glass Front Media Units, we coordinate the module widths and shadow gaps once, rather than letting two trades interpret the same elevation separately.
  • Interior back panel: plain, textured or lit recess. This is decided with the layout, not after it.

3. Glass and door type

The glazing choice changes cleaning effort, how much of the contents you want visible, and how the unit reads in a room. Clear glass opens the wall up and shows everything, including the spines you meant to hide; frosted or ribbed glass softens the contents while keeping light passing through; smoked glass tints the view and works well against pale joinery.

  • Clear, frosted, ribbed or smoked glass, confirmed as a physical sample before sign-off.
  • Hinged, sliding or lift-up doors. Sliding doors need track clearance and a solid fixing line; hinged doors need the swing checked against the room layout.
  • Frame detail: slim aluminium frame or an all-board door with a rebated glass rebate, matched to other joinery in the property.
  • Handles, push-open hardware or finger pulls — and whether children use the room.

4. Materials and finishes across the whole fit-out

A bookshelf rarely stands alone. In villa and apartment work we produce it in the same board, edge and lacquer schedule as the wardrobes, media wall and kitchen run, so grain direction and sheen match from room to room. Our custom furniture materials and finishes service covers carcass substrate, door core, veneer, lacquer, melamine and acrylic surfaces, plus metal frame colours.

Two practical notes we always raise at this stage. First, ask for a finish sample of the exact door, carcass and edge band together — a board sample can look right while the edge band reads lighter under site lighting. Second, decide how the unit meets built-in furniture next to it: butted, shadow-gap, or trimmed with a beading. That detail belongs on the drawing before production.

5. Lighting inside the cabinet

Glass fronts and lighting are decided together, not left to the electrician. Interior lighting turns a bookshelf into a display wall, but it needs a driver location you can reach, cable routes inside the carcass, and a switch or sensor position agreed with the electrical plan. Where a run includes lit niches or an integrated cabinet lighting detail, we confirm the electrical specification and compatibility for that specific configuration before the carcass panels are cut.

6. Hardware, tolerances and site conditions

  • Hinge and slide brand or duty class, plus soft-close where required — written into the specification rather than left to “equivalent”.
  • Wall fixing method for the substrate on site: masonry, stud partition or a timber batten frame. Full-height glazed units need a designed fixing line.
  • Glazing protection and packing for shipping. For overseas projects we agree how doors and glass panels travel — assembled or loose — and how they are unpacked on site.

7. Commercial terms to settle before production

Custom built-in work only goes smoothly when the approval sequence is agreed at the start. For SANTERSON projects we confirm: a signed elevation with dimensions and shelf pitch; a material and finish sample pack approved in writing; the electrical and fixing details issued by your side; then production release. Assembled units, glazed doors and interior lighting each have their own sign-off points, so build them into your programme instead of assuming one approval covers all three.

As a China-based manufacturer of furniture and building materials, we handle design, custom/OEM production, door-to-door delivery, installation support and after-sales service as one package — useful when the bookshelf, wardrobes, wall panelling and finishes for the same property come from different suppliers on a drawing.

What to send us for a quotation

  • A marked-up elevation or sketch with overall width, height and depth, plus shelf pitch you want.
  • Door type and glass type, with the frame detail if it has to match existing joinery.
  • Finish references (board, veneer, lacquer or colour code) for doors, carcass and interior back panel.
  • Whether interior lighting is required, and who supplies the driver and control.
  • Delivery address, access constraints and the on-site substrate the unit fixes to.

If you send those six items, we can price the run properly and flag the details that normally cause rework — shelf spans, glass type, driver access and fixing lines — while they are still cheap to change. Santerson Glass Front Bookshelves are made to the dimensions and finishes of your project; confirm the final dimensions and selected specifications against the approved drawing before production begins.

To discuss a bookshelf wall, media wall or a wider joinery package for a residential project, contact SANTERSON — PHILLIP, phone/WhatsApp +86-13928214007, email santerson@qq.com.