A glass-front tall cabinet looks simple on a drawing: one floor-to-ceiling box, one glazed door, a run of shelves inside. On site it is often the piece that decides whether a pantry, laundry or bathroom joinery wall reads as designed or as cluttered. That is exactly why we get so many enquiries about Santerson Glass Front Tall Cabinets that arrive before the drawing is finished and after the tender date has been set. The cabinets in this collection are made to order for each project, with the finish, layout and dimensions specified per space, so the quality of your questions determines the quality of what arrives in the container.
Below is the checklist our production and project teams actually work from when a glass-front tall unit moves from enquiry into manufacturing. Read it before you send a drawing, and you will shorten the confirmation round instead of adding one.
1. Which room is this cabinet serving?
The Tall Cabinets collection covers several very different jobs, and the specification conversation changes with each one. A unit closing a kitchen run has to hold dry goods, small appliances or glassware at heights people reach daily. A unit in a bathroom or laundry stores towels, linen and cleaning products, where humidity, splash zones and ventilation enter the picture. A unit that carries an appliance brings dimensions, clearances and services into the frame.
Tell us the room first, then the use. If your glazed tall unit sits next to a shower enclosure or a wet area, say so on the drawing rather than leaving it to be inferred from the elevation. Where a laundry or bathroom fit-out also needs closed storage, Santerson Utility Tall Cabinets are usually specified alongside the glass-front units so the open display and the concealed storage share one line, one finish and one shadow gap.
2. What is actually going behind the glass?
Glazing is not decoration; it is a promise about what people will see. So the first question we ask is what you intend to display and what you would rather hide.
- Fixed shelves, adjustable shelves or a mix? Shelf centres should follow the tallest item you plan to store, not a default grid. Bring bottle heights, plate stacks and appliance heights to the drawing.
- Full-height glazing or glazed upper with a closed lower section? A closed base hides the items nobody wants on show and gives the carcass a solid plinth detail.
- Interior lighting or none? Lit display cabinets read very differently at night; if you want lighting, plan the driver position and a switch or sensor at the design stage, not after production.
- Doors hinged or sliding, and which way do they swing past the traffic lane? Check the door against the room circulation before confirming the elevation.
Where part of the wall should stay open for daily access, Santerson Open Shelf Tall Cabinets let you alternate open bays with glazed bays in the same run while keeping one carcass construction and one finish.
3. Which glass, and what does it have to survive?
Glass is where specification mistakes become expensive, because the panel is custom cut and cannot be trimmed on site. Be explicit about:
- Clear, frosted, ribbed or tinted glass. Clear shows everything inside; frosted and ribbed soften the view while still reading as a glazed door. Tinted glass changes how the interior contents and any lighting present.
- Framed or frameless door. An aluminium-framed glazed door gives a crisp shadow line and a rigid edge; a fully framed timber-look door carries the panel profile of the surrounding cabinetry.
- Handle detail. Routed, integrated or applied handles change finger clearance, and on a tall unit they set the visual rhythm of the whole wall.
- Glass type and thickness for the location. We will confirm the glass specification for each selected configuration with you before production. Ask for it in writing rather than assuming the showroom sample is what ships.
One practical note: a glazed door that looks right on a render can show fingerprints, shelf shadows and stored clutter in daylight. If the cabinet sits opposite a window, ask us for a larger sample of the glazing option so you can judge it against your own light.
4. What are the real dimensions, and what is fixed around them?
Tall units fail most often on site because of what sits next to them, not because of the cabinet itself. Before you order, confirm:
- Finished floor level and finished ceiling or soffit height, including tile thickness and any screed build-up.
- Whether the unit runs to the ceiling with a filler, a bulkhead or a shadow gap — and who is building the bulkhead.
- The position of outlets, switches, water points and floor drains relative to the carcass.
- Door and skirting returns, plus any corner condition. Corner conditions in the same collection are covered by Santerson Corner Tall Cabinets.
- Floor flatness and wall plumb over the full height of the run. On a unit close to the ceiling, a leaning wall is visible.
Send us the measured survey, not the architectural model dimension alone. Made-to-measure sizing means we build to your numbers, so the numbers have to be the ones that exist on site at handover.
5. Is an appliance going into this cabinet?
If the tall unit is meant to stack ovens, take a drawer microwave, or hide a washer or dryer, that decision changes the carcass, not just the shelf plan. You need the exact appliance model, its cut-out dimensions, its ventilation route and its electrical requirement before we confirm the elevation. For those runs we specify Santerson Integrated Appliance Tall Cabinets, where appliance dimensions, ventilation and electrical requirements are confirmed for each project.
If the appliance has not been selected yet, do not let that hold up the rest of the joinery package. Tell us the intended category and we will reserve a standard carcass width and ventilation provision, then close it out once the model is fixed.
6. Which finish, and does it match what has already been ordered?
Glass-front tall cabinets rarely stand alone; they sit inside a wider cabinetry package. Specify the panel material, the surface finish and the edge treatment in the same language your other suppliers are using, and check the glazed door against the solid doors beside it under the same light. Colour, sheen and grain all shift between samples.
Our custom and OEM service covers bespoke finishes, textures and materials alongside custom furniture design and prototyping, so a glazed door can be brought to the same finish as the surrounding run rather than being accepted as a mismatch. For projects that need matching cabinetry elsewhere in the building — kitchens, wardrobes, vanities, media walls — ordering the whole joinery package from one factory removes the reconciliation problem entirely.
7. Who is checking it before it ships?
Ask for a production drawing you can sign: elevations with dimensions, shelf positions, door swing and glazing type marked on each unit. That signed drawing is the reference for both sides when the crates arrive.
Then agree the inspection and packing detail. Tall glazed units travel differently from flat packs — glazing needs protection, corner protection and clear crate labelling so the right unit goes to the right wall on site. Our logistics covers freight forwarding by sea, air and rail, customs paperwork, packaging and container loading, shipment tracking and door-to-door delivery, so we plan how these units are crated and loaded rather than leaving it to the consolidator.
8. Who installs it, and what happens if something is wrong?
Decide early whether your local trades or our team handles installation. Glazed tall units need the carcass packed, plumbed and anchored properly before a glass door is hung, and a misaligned carcass shows immediately once the glazing is on. Our services include on-site installation with inspection and snagging, plus warranty coverage, spare parts and ongoing maintenance; confirm the scope, terms and response arrangements for your project location before the order is placed.
A short note on what we do not promise
We will not quote you dimensions, glass thickness or load ratings that have not been confirmed for your configuration. Specifications for these cabinets are set per project, and the figures on a product page are indicative rather than fixed. That is deliberate: a tall glazed unit specified from memory is the fastest way to an expensive correction after production has started.