A pocket door disappears into the wall cavity, so nothing swings into the room and no floor track collects dust. That is exactly why buyers specify classic pocket doors for bathrooms, pantries, studies and bedroom suites where every square metre of floor area matters. It is also why they cause so many site problems when the opening detail is settled too late.
The difference between a clean installation and a snag list usually comes down to what was agreed before production started. Below are the points worth putting in front of the manufacturer while the drawings are still open.
1. Rough opening, wall build-up and pocket depth
Pocket doors are sized by the opening they close, but they are installed into a cavity they must disappear into. Before anything is quoted, confirm three numbers: the clear opening width and height, the finished wall thickness, and how deep the pocket can be.
A single pocket needs the full door leaf plus clearance; a bi-parting pair needs two pockets inside one opening. Where the wall build-up is thinner than the frame assembly requires, that decision changes the stud setting, not the door. Raise it early, while the partition layout can still move.
- Clear opening width and height, plus finished floor level on both sides of the opening.
- Wall build-up — stud size, lining material and the finished face treatment either side.
- Available pocket depth, and whether services run through the section that has to be boxed out.
- Whether the header carries load, which affects how much of the opening can actually be framed out.
2. Single or bi-parting, and what sits in front of the door
State the operating arrangement in the enquiry rather than leaving it to be inferred. A single pocket suits a narrow bathroom or store. A bi-parting pair suits a wide opening between a bedroom and its dressing area, where two leaves meet at the centre and each leaf slides into a pocket at its own end.
Then check what competes with the pocket. Skirting, architraves, wall lights, switches, towel rails, robe interiors and cabinetry returns all sit in the same wall. A light switch placed on the pocket side leaves nowhere to slide. Fix the furniture layout first, then set the door.
3. Panel design: keeping a classic door classic
A classic pocket door carries its style in the leaf — moulded or recessed panels, stiles and rails, and the profile of the edge. Because the leaf is made to measure for each project, panel layout can be matched to the joinery and hinged doors elsewhere in the same dwelling, so the profiles read as one set rather than separate purchases.
Decide these with the drawings:
- Panel style and count, and whether the stiles and rails line up with the architrave or skirting profile you are already using.
- Whether both faces of the leaf are finished, since a pocket door is visible from two rooms — and from both when the leaf sits part open.
- Edge treatment on the hanging stile and the meeting edge, particularly for a bi-parting pair where the two edges close together.
- Glass or glazed panels, if wanted. A glazed pocket door suits studies and dressing rooms where borrowed light matters; a wood veneer leaf in Wood Veneer Pocket Doors suits a more traditional scheme.
4. Finish and how it is protected in transit
Say what the finish has to match — a floor, a wardrobe front, a painted joinery set — and send the reference rather than a description. Lacquer sheen, veneer cut and grain direction, and colour all read differently on a tall, narrow leaf than on a wide cabinet door.
Ask how finished leaves travel. Loose or field-applied architraves, edge protection, and separated hardware packs are the practical difference between leaves that arrive ready to hang and leaves that need touching up on site after the walls are painted.
5. Hardware: track, runners, and what you want to feel when you pull it
The hardware is invisible once installed but determines how the door behaves every day. Specify:
- Track and runner duty rated for the finished leaf weight, not the bare panel.
- Soft-close or soft-start action, if the door serves a bathroom or bedroom next to a sleeping space.
- Flush pull, edge pull or finger recess — and whether you want visible hardware at all.
- Lockset, privacy set or plain passage, plus dummy handles on the opposite face where symmetry is expected.
- Floor guide or top-hung arrangement, and clearance for the carpet or flooring you have specified.
Send the door schedule as a list of openings with an operating note against each. Hardware ordered to the wrong weight class is one of the most common reasons a pocket door needs to come back out of the wall.
6. Alignment with the wall face
A pocket door should sit flush with the lining on both sides and read as part of the wall when closed. Where a shadow gap, a feature architrave or a panelled wall is intended, that detail needs to be drawn before the frame is made — not resolved with packers on site.
If the design calls for the door to vanish entirely into a panelled surface, discuss Decorative Concealed Doors and integrated panelling at the same stage as the pocket doors, so one wall detail governs both.
7. Making it with the rest of the joinery, in one order
Pocket doors rarely stand alone in a project. Wardrobe fronts, cabinetry, skirting and architraves are usually specified around them. Ordering the doors together with turnkey villa furnishing and fit-out work means one party reconciles the profiles, finishes and opening sizes, instead of three trades each working from a different drawing revision.
For buyers outside China, this also collapses several shipments into one coordinated delivery. The Custom & OEM Service covers made-to-measure sizing, material and finish selection and prototype review before full production — useful when a classic profile has to match existing joinery on a renovation.
8. What arrives on site, and who fits it
Confirm the delivery scope in writing: whether frames, leaves, architraves and hardware ship together or in separate consignments; how the leaves are packed; and what installation support is available. Pocket doors need setting out while the wall is still open, so a late frame delivery means the cavity gets closed without the frame inside it.
Agree who sets the frame, who hangs the leaf, and who carries out the final adjustment after flooring and painting are complete. The installation and after-sales support service covers on-site fitting, inspection and snagging — but the sequence has to be written into the programme before the partitions are closed.
A short list to send with your enquiry
Send these items and you will get a quotation that does not need reopening:
- Door schedule: opening width and height, single or bi-parting, and the room each door serves.
- Wall build-up drawing for each type, with pocket depth and finished wall thickness noted.
- Panel style reference and finish sample or colour reference for both faces.
- Hardware preference: track duty, soft-close, pull type, lockset.
- Floor finishes at the opening, so the guide and clearance are set correctly.
- Delivery address, target on-site date, and who is fitting the frames.
Confirm dimensions and selected specifications for each project before production begins. Once those details are agreed at drawing stage, a classic pocket door does what it promises: it closes flush with the wall, and the floor space in front of it stays yours.