A swim spa that looks right on a mood board can still stall on site. Before the Outdoor Swim Spa WS-S06 reaches a villa terrace, a resort deck or a hotel outdoor level, the model has to survive contact with drawings: setting-out plans, structural slab notes, electrical layouts, drainage routes and access paths. The following coordination checklist is written for architects, contractors and procurement teams who need the spa reflected accurately in documentation before anything is ordered.
Start With the Catalogue Envelope, Not a Rendering
The first job is to transfer the published footprint into the drawing set as an envelope with working clearance, not as a picture block. The WS-S06 is listed at 5820 × 2220 × 1110 mm (length × width × height). Treat those figures as the shell dimension and then add what the installation actually consumes: steps or an access platform at one end, plant and control access on the equipment side, a maintenance gap behind removable panels, and clearance for anyone walking past the water features. A spa that fits on paper by a few centimetres becomes a site problem the moment someone needs to open a panel or replace a filter cartridge.
Plot the envelope on the plan at the same scale as the surrounding hardscape, then dimension it against fixed references — the pool deck edge, a pergola post line, a balustrade, a drainage channel and any structural beam above. That single step exposes most conflicts early: a door that will not swing past the spa corner, a lounger zone that loses its walking route, or an overhead structure that clashes with the waterfall discharge.
Confirm the Model Designation Inside the Drawing Set
The WS-S06 sits in a family of closely related configurations — variants with different overall heights and equipment packages, some carrying swim training systems or temperature controls that this model does not list. Because the sub-designations differ by only a letter or two, a specification written as "WS-S06 series" invites substitution at tender stage. Record the exact model code on the schedule, on the quotation reference and on the packing documentation, and state in the notes which features are required for the project.
| Model | WS-S06 |
| Catalogue dimensions | 5820 × 2220 × 1110 mm |
| Total power (catalogue) | 6.35 kW |
| Water pump / filter pump | 2 pcs / 1 pc |
| Jet total (catalogue) | 56 pcs |
| LED lighting (catalogue) | 2 lights plus 18 small LED lights |
| Control system | 1 set |
| Features shown on the product page | Water jets, LED lighting, Ozone, Waterfall, 4 water columns |
Values transcribed from the published WS-S06 product page. Confirm them against the quotation for the specific configuration before they are frozen into a construction document.
Read the Power Figure as a Starting Point for the Electrical Design
The catalogue states total power of 6.35 kW for this model. Use that number to position the electrical room, cable routes and isolation points in your first coordination round — but do not let it become the final load schedule entry on its own. Optional equipment commonly added to swim spas in this range, such as a heat pump, UV sterilization or an additional water pump, changes connected load, circuit sizing and protection requirements. Ask for the load figure of the exact configuration selected, including which options are included, and have the electrical engineer design to that figure rather than to the base catalogue value.
Practical drawing items worth marking at this stage:
- A dedicated supply point and local isolator placed outside the splash zone but within reach of an operator.
- Cable containment routed away from the excavation and drainage works, so later trenching does not cut through it.
- Conduit spare capacity for control wiring, lighting circuits and any future heat pump.
- A labelled note on the electrical drawing stating which equipment list the load was based on and its revision date.
Set the Support Structure and Tolerance Before the Deck Is Built
A filled swim spa is a heavy, point-loaded object sitting on a finish build-up, so the structural question belongs with the slab or deck design rather than with the landscaping package. Confirm with the structural engineer what bearing the finished terrace provides at the spa location, and whether a upstand, reinforced pad or steel frame is needed to carry the shell evenly. Where the spa is set into a deck, agree how the finish material meets the shell edge and who owns that interface — usually it is worth showing a separate detail for the perimeter trim rather than leaving it to site discretion.
Level tolerance is the second item that generates rework. Show the level requirement for the supporting surface on the drawing, and check the finished deck level on site before delivery. A shell seated on an uneven base transmits stress to the cabinet and shows up later as trim gaps and drainage falls running the wrong way.
Check the Delivery Route Before the Unit Is Manufactured
The WS-S06 is a single long shell, so the access question is decided by the tightest point on its route from the vehicle to the terrace: gate width, a side passage, a turning corner, a lift car or a balcony door. Measure those openings and record them in the drawing notes while there is still time to change the delivery method — an upper-level installation may need a crane, which affects both cost and the site programme. Confirming access early also lets you decide whether the spa should be delivered before or after the deck finishes are laid.
Plan Water Supply, Drainage and Commissioning Access
Fill, drain and overflow routes need a home on the services drawings before the spa position is fixed. Mark the fill connection with a shut-off valve that stays reachable once the deck is complete; mark the drain route with its fall and termination point; and confirm where water from the waterfall and the four water columns discharges, so it does not land on a walking surface or a drainage inlet that cannot take the flow. Add a drain-down or winterisation point if the installation will ever be taken out of service.
Then walk the route with your eyes on the maintenance panel rather than the water feature. The filter pump, control system and jet plumbing sit behind panels, and they need real access — enough room for a person to work in, plus a path from the plant area to the spa that stays clear of finished planting and furniture. Commissioning also needs somewhere to test: a place to fill, run the pumps and jets, check the ozone and lighting circuits, and hand over records. Building that sequence into the programme avoids a situation where the spa is installed but cannot be handed over because the surrounding works are unfinished.
Coordinate the Spa With the Rest of the Outdoor Package
A swim spa rarely sits alone. In villa and resort projects it shares a terrace with outdoor furniture, shade structures, loungers and circulation routes, and all of those need to be resolved on one drawing rather than in separate tenders. Check sightlines from the main viewing points, make sure shade structures do not sit over the waterfall discharge, and keep sun lounger positions clear of spray zones. Where pergolas or hardtop gazebos are part of the design, confirm their post bases do not conflict with the spa envelope or its cable and drainage runs.
Because SANTERSON supplies both the Swimming Pools and Swim Spas range and the surrounding outdoor furniture, pergolas and interior fixtures, one supplier can align the product schedule, the delivery sequence and the site instructions across those packages. For projects that need it, turnkey project solutions cover design coordination, production, logistics and installation support, which keeps a single party accountable for the interfaces around the spa instead of leaving them to be sorted out between trades.
What to Send With an Enquiry
To get a coordinated quotation back rather than a generic product sheet, send:
- The plan extract showing the spa envelope with clearances and finished deck levels.
- A section through the intended support structure and perimeter trim.
- The equipment list you want quoted, including heating, sterilization, insulation and steps if required.
- Delivery access details: vehicle size, lift or crane availability, gate widths and storage area on site.
- Your target installation window, so production and shipping can be sequenced against the site programme.
Planning a swim spa into a villa, resort or hotel outdoor area? Send us the drawings and the configuration you have in mind, and our project team will return a coordinated proposal for the WS-S06 — product schedule, options, delivery sequence and installation support.
Contact SANTERSON: PHILLIP · Phone/WhatsApp +86-13928214007 · Email santerson@qq.com · Enquiry page