Glass shelves look like the smallest line item in a bathroom or living-area package, and that is exactly why they cause problems on site. A shelf arrives without a written glass specification, the fixings do not match the wall build-up, and the joiner spends half a day on a bracket detail nobody agreed. Before an order is placed, procurement teams should have six items in writing for every Santerson Glass Shelves position: the dimension set, the glass specification, the load duty, the support and fixing method, the substrate behind the shelf, and the sign-off route for shop drawings.
Start with the dimension set, not the finish
The catalogue presents these shelves as configurable units for residential bathroom projects, with made-to-measure sizing and material and finish options. That is useful for design freedom but dangerous for procurement if nobody owns the dimensions. Record depth, width and the vertical spacing between shelf levels for each position, and state which room drawings those dimensions came from. Where a shelf returns into a corner, or where a project also uses Santerson Corner Open Shelving, note the return dimension and the wall it lands on.
Second, record who measured. If dimensions come from a site survey rather than issued drawings, say so in the requisition. A made-to-measure item ordered off an unsurveyed drawing is a variation order waiting to happen.
Write down the glass specification you actually want
The product page does not publish a fixed glass build, and that is deliberate: the specification is confirmed per project. Your purchase document should state the glass type, the thickness to be quoted, edge finish, and whether any corner or cut-out detail applies. Do not let "glass shelf" travel through three emails and become an assumption.
For bathroom positions in particular, ask how the specified glass is intended to be cleaned and maintained, and record the answer. The same discipline applies across the wider glass range: the pages for Santerson Glass Sliding Panels explicitly ask buyers to confirm glass type and safety requirements for each project, which is a reasonable template for how to handle shelf glass as well.
State the load duty in the requisition
The listing asks buyers to confirm load limits and installation requirements for each project. That means the intended use belongs in your document, not in a designer's head. Write down what the shelf will carry: bottled product and light accessories on one hand, heavier ceramic vessels, glass front storage or stacked stock on the other. Then ask for the span, support spacing and fixing pattern that matches that duty.
If a position is expected to carry anything unusual, such as a display piece in a glass front bookshelf, or product weight in a tall storage run next to Santerson Open Shelf Tall Cabinets, flag it as its own line item with its own load note. Grouping it under "general shelving" is how load questions get lost.
Name the support method and who installs it
Shelves are supplied as part of an open shelving family that also includes Santerson Metal Frame Shelves, Santerson Freestanding Open Shelves and Santerson Floating Modular Shelves. Each support logic behaves differently on site: a wall-fixed glass shelf needs brackets, fixings and a suitable substrate; a freestanding unit needs floor clearance and stability confirmation; a modular system may involve hardware and, where lighting is integrated, electrical coordination. Record which option you ordered and what interface your trades own.
Where the design includes shelving accessories or integrated lighting in a modular wall system, add a line confirming compatibility and the electrical specification to be provided. Pages for those systems ask buyers to verify hardware and electrical options per configuration, so put that question in writing before production rather than at handover.
Describe the wall behind the shelf
This is the item most often missing. A glass shelf fix detail only works if someone has documented what it is fixing into: tiled masonry, a framed partition with lining, timber battening, or a panelled surface from the Santerson Glass & Glossy Panels range. Note the wall build-up, any waterproofing layer that must not be penetrated, and whether blocking or reinforcement is required behind the fixing line.
In wet areas, also record shelf position relative to showers, basins and mirror cabinets so the fixings do not clash with services. Where a project uses Santerson Glass Partitions or niche detailing alongside shelving, list those adjacent items on the same drawing sheet so the coordination is visible.
Put the sign-off route in the order
Because these are configurable products supplied by a one-stop project furnishing supplier, the practical control is a shop-drawing cycle: dimensions, glass specification, load note, fixing detail and finish sample on one sheet, signed by whoever holds design authority on your project. Record the revision number of the drawing that sheet answers to.
| Document | What it must state for a glass shelf position |
|---|---|
| Requisition / PO line | Room and position code, ordered configuration, made-to-measure dimensions, finish reference |
| Glass schedule | Glass type and quoted thickness, edge detail, cut-out or corner notes, maintenance expectation |
| Load note | Intended contents and duty, span and support spacing as confirmed for that duty |
| Fixing sheet | Bracket and fixing type, substrate build-up, reinforcement behind the fix line, waterproofing constraints |
| Interface list | Adjacent basins, showers, mirror cabinets, partitions and panelled surfaces; who installs what |
| Approval record | Signed shop drawing, drawing revision it answers to, date and name of approver |
Frequently asked questions
Why is there no standard size published for these shelves?
The listing is written as a configurable, made-to-measure product: sizing, finish and layout are specified to suit each space. The confirmed dimension set for your project is the specification.
Can one load note cover every shelf in a bathroom package?
No. The page asks for load limits to be confirmed per project, and positions differ in what they carry and how far they span. Write a duty note per position or per group of identical positions.
Who is responsible for the fixing detail?
Installation requirements are confirmed project by project, so the fix detail should be agreed in writing between supplier and your site team, with the wall build-up documented before production starts.
If you are packaging glass shelves with other bathroom fixtures or built-in joinery for a villa or hotel fit-out, send the six documents above with your enquiry so the quotation answers them. That single step turns a small accessory line into a controlled scope item.