Classic folding doors solve a problem most project teams meet twice: an opening that needs to be wide when the room is in use and compact when it is not. They fold against the reveal instead of swinging into circulation or sliding across a fixed track, which makes them useful for pantry entries, service servery openings, dressing-room fronts, partition walls between living and dining areas, and store rooms tucked into villa joinery. Shortlisting the wrong manufacturer, however, turns that benefit into a door that binds, a leaf stack that fouls the architrave, or a finish that does not match the cabinetry beside it. The checklist below is what we ask buyers to settle before they compare quotations.
Start With the Opening, Not the Door
Folding doors fail at shortlist stage for one recurring reason: the opening was specified before anyone decided how the leaves would stack. Before you request prices, fix four facts on drawing.
- Clear opening width and height, measured to the finished floor and finished ceiling level, not the structural shell.
- Stack side and stack depth — which wall the leaves collapse against, and how much of that wall you are willing to give up.
- Leaf count and leaf width — wider leaves look cleaner but need stronger hardware; more leaves fold tighter but multiply the number of hinge lines.
- Track decision — top-hung, bottom-rolling or a combination. This follows from your floor finish and threshold requirement, not from preference.
A manufacturer who quotes without these four items is quoting a catalogue item, not your door. Made-to-measure sizing is the baseline for this category; if a supplier cannot state how they take or verify site dimensions, treat that as an early exclusion.
Six Checks That Separate Manufacturers From Resellers
1. Can they build to your size and finish, in-house?
Ask what is manufactured under the same roof as the doors: leaf cores, frames, finishes, ironmongery preparation. A factory that also produces wardrobes, wall panelling and cabinetry is a useful signal for classic folding doors specifically, because the door has to disappear into surrounding joinery. Our built-in furniture range sits in the same production stream as our doors, so panel profiles, veneer species and lacquer colours are matched rather than approximated.
2. Do they show you a folding-door family, not one product?
Classic detailing has variants: paneled timber leaves, glazed leaves for borrowed light, veneered leaves that continue a wall finish. A supplier with several folding types can advise on which suits the room; a supplier with one SKU cannot. Our collection covers classic folding doors, wood veneer folding doors and glass folding doors, all specified per project for dimension, layout and finish.
3. How do they handle the interface details?
The expensive mistakes are interfaces: the head condition where the track sits, the threshold at a tiled junction, the architrave return, the seal against an adjacent panelling system. Ask for detail sketches of these four conditions on your project before award. If a supplier will not draw them, they will be invented on site.
4. What is their finish and material range in practice?
Ask which species, veneers, lacquers and glass options are stocked versus made to order, and whether a physical sample can be issued for the exact finish quoted. Marketing images do not settle colour; a sample does.
5. What is the site-measurement and approval sequence?
A reliable sequence looks like this: drawing-based enquiry, quotation with confirmed dimensions and specification, site verification or second-fix measurement check, production approval, then dispatch. Written confirmation of dimensions and selected specifications before production protects both parties; a manufacturer who starts work on unverified openings is carrying your risk on their clock.
6. Who answers when the door arrives?
Confirm what happens for transit damage, missing ironmongery, and a leaf that needs adjustment after handover — and who coordinates it. For overseas manufacturing this is where project teams feel the difference: one contact through design, production, logistics and installation support, or several parties passing messages.
Shortlist Scoring Sheet
Score each candidate 0–2 per row. Two points means they have done it on a comparable project and can show documentation; one point means they say they can; zero means silence.
| Criterion | Evidence to ask for |
|---|---|
| Made-to-measure sizing | How site dimensions are verified before production release |
| Folding-door range breadth | Panelled, veneered and glazed types in one collection |
| Interface detail drawings | Head track, threshold, architrave, panel junction |
| Finish matching to joinery | Sample of the quoted finish; same factory as cabinetry |
| Custom/OEM capability | Prototype or mock-up route for bespoke profiles |
| Packaging and container loading | Packing method for glazed and tall leaves |
| Installation and after-sales | Named support contact, snag and spare-parts process |
Common Shortlisting Mistakes
- Comparing prices before the stack is fixed. Two quotations for the same opening can differ because one assumes four leaves and the other six, or because one includes a floor track and the other does not.
- Treating ironmongery as an accessory. Hardware duty follows leaf weight and width; ask who specifies it and what load rating is being supplied.
- Accepting a finish name instead of a sample. "Oak" or "matte white" covers many different products.
- Ignoring the neighbours. A classic folding door read against mismatched skirting, architrave or wall panelling looks like an afterthought no matter how well it operates.
Working With a One-Stop Supplier
Doors rarely sit alone on a project bill. Wardrobes, vanities, wall panelling, lighting and flooring are usually specified in the same window, and split suppliers mean split responsibility for the junctions between them. SANTERSON has operated since 2008 as a China-based furniture and building materials manufacturer, supplying doors together with the joinery and finishes around them under turnkey solutions for villa, hospitality and office projects. Enquiries move through design and planning, production, logistics and door-to-door delivery, then installation and after-sales support — a single route you can hold to account.
Send us the opening dimensions, the intended stack side and the joinery the door must match, and we will confirm the layout, finish options and specification for your project before any production is released.