Open display niches look simple on a drawing. A recess in a wall, a shelf inside it, a finish that matches the rest of the joinery. That apparent simplicity is exactly why quotations for them vary so widely, and why two proposals that appear identical can produce very different results on site. If you are specifying Santerson Open Display Niches for a villa or apartment fit-out, the sample and the written proposal are where the real differences between suppliers become visible. This article walks through what to ask for, what to compare line by line, and which details usually decide whether the finished wall reads as built-in joinery or as furniture pushed against a wall.

What you are actually buying when you order open display niches

Santerson Open Display Niches sits within the Integrated Storage Walls collection, alongside Santerson Mixed Open & Closed Storage and Santerson Full Height Storage Walls. The catalogue describes the range as designed for residential wall-system projects, with project-specific dimensions and finish options: sizing is made to measure, and layout, material and finish are specified per space rather than chosen from a fixed size grid.

That description matters for comparison work, because it means there is no single standard price or standard build for this product. What you receive depends on the specification you and the supplier agree. Two quotations can both say "open niche, oak veneer, 1200 mm wide" and differ in how the niche box is constructed, how the shelf is supported, how the finish wraps the visible edges, and how the unit meets the surrounding wall. Comparing proposals therefore means comparing build details, not just headline dimensions and a total.

A practical rule: if two quotations for the same niche differ by a large margin, the difference is almost always in what is not written down, such as edge treatment, substrate, fixing method, or how the surrounding panels are carried. Ask each supplier to state those items before you treat their price as comparable.

Step 1: Put both proposals on the same specification sheet

Before requesting samples, write one neutral specification sheet in your own words and send it to every supplier you are quoting. Include the information a factory needs to price the same thing twice:

  • Clear opening width, height and depth of each niche, and whether those dimensions are finished faces or structural openings.
  • Position relative to floor, ceiling and adjacent doors or windows, plus the wall build-up if you know it.
  • Number and position of internal shelves, and whether they are fixed, adjustable or on concealed supports.
  • Required finish for interior surfaces and for the visible frame reveal, including grain direction where grain-matched panels meet.
  • Lighting intention: none, recessed line lighting, or integrated cabinet lighting coordinated with the panel build.
  • What abuts the niche: full-height storage wall, media wall, wardrobe run, or plain plasterboard.

Suppliers who receive a specification like this price against it. Suppliers who receive only a marked-up plan will each interpret it differently, and you will end up comparing three different products at three different prices. Santerson's own workflow starts with a project brief and design proposal before quotation and detail confirmation, which is the same logic from the manufacturing side: details are fixed first, then priced.

Step 2: Request samples that show the joint, not just the colour

A colour chip tells you almost nothing about an open niche. Ask instead for a sample that reproduces the detail you will actually receive. For this product type, request:

  • A corner or edge sample showing the visible reveal of the niche, so you can see how the finish wraps the return and whether the edge is a solid banding, a mitred wrap or a moulded profile.
  • The shelf-to-side junction, showing how the shelf is fixed and whether any fixing is visible from the front.
  • The finish surface in both matte and reflective light. Veneers and lacquers read very differently at an angle and straight on, and a sample photographed flat hides this.
  • The substrate cross-section, so you can see the board construction behind the decorative face rather than taking it on trust.

Where the proposal mentions material families such as wood, metals, engineered stone or laminates, which are the finish options described on Santerson's Custom & OEM service page, ask for the sample in the exact combination quoted rather than a representative panel. A laminate face on one substrate and the same face on another behave differently at edges and in humid rooms.

Step 3: Score each sample against five practical tests

Once samples arrive from each bidder, evaluate them the same way. These five checks separate useful detail from a good-looking photograph:

TestWhat to look forWhy it matters on site
Edge and reveal qualityContinuity of grain or colour around the corner; no gaps, telegraphing or thin spots on the wrap.The niche reveal is the part you look at every day; flaws read as poor workmanship from a metre away.
Shelf supportWhether supports are concealed, and how the shelf resists deflection at the quoted span.Long open shelves loaded with books or stone objects sag; a sample shows whether the quoted build is adequate.
Finish durabilityWipe the surface, then check for dulling, lifting at edges, or colour change.Display niches are dusted and touched constantly; a finish that marks becomes a maintenance problem for the owner.
Lighting integrationHow cable routes, drivers and any recessed channel are handled in the sample build-up.Reworking lighting after installation means removing panels; it should be resolved at sample stage.
Dimensional accuracyMeasure the sample against your stated dimensions and check squareness.Built-in wall systems meet floors and ceilings that are never perfectly true; tolerances must be agreed, not assumed.

Record the results in one table and send it back to each supplier with the gaps highlighted. A supplier who answers those gaps in writing has shown you their real capability; a supplier who replies "don't worry, we always do it properly" has told you something too.

Step 4: Compare the written proposals line by line

With samples scored, turn to the paperwork. The following items are where quotations for a made-to-measure wall system diverge most often, and each one should appear explicitly:

Proposal itemGood proposal saysWeak proposal says
Scope of supplyWhich panels, niches, shelves and trims are included, and which are excluded."Storage wall as per drawing", with no exclusions listed.
Specification referenceYour specification sheet or shop drawing number quoted on every line item.A product name only, with no revision or drawing reference.
Finish identificationNamed finish plus sample reference, including grain direction for veneers."Oak", "grey", or a colour code with no physical sample attached.
Site interfaceWho prepares the wall, who supplies setting-out, and how skirting and cornices are dealt with.Silence, leaving the builder and joiner to argue it out later.
Survey and measurementWho takes final site dimensions and when, and how discrepancies are handled.Assumes client-supplied dimensions with no verification step.
Delivery and packagingPackaging standard, container or pallet arrangement, and delivery point for cross-border projects.A single "freight" line with no detail on scope or trade terms.
InstallationWhether installation is included, by whom, and what site conditions are assumed.Supply only, discovered after the order is placed.
After-sales termsWhat is covered, for how long, and how spares or replacement panels are ordered."Warranty on request".

For cross-border work this last group of items carries more weight than it would with a local shop. Santerson's stated services include custom and OEM manufacturing, logistics with door-to-door delivery, and installation and after-sales support; the site also describes a six-stage flow from consultation through design, production, logistics and installation to after-sales. Read those as scope options you must confirm for your project rather than automatic inclusions: which stage is included in your price, who coordinates on site, and what documentation you receive are all things to fix in writing before production starts.

Step 5: Check the supplier's track record on comparable walls

Ask for photographs and drawings of storage walls and display niches the supplier has actually delivered, ideally in the same market. Santerson publishes project cases including villa work in Willoughby, Perth, North Turramurra, Melbourne and Sydney, with cabinetry and joinery shown for some of them. When you review any case study, yours or another supplier's, ask three questions: what was the actual scope, can the supplier show shop drawings as well as finished photographs, and are the images of delivered work rather than a showroom.

A supplier who can walk you from drawing to sample to installed wall is demonstrating process. A supplier with beautiful photographs only is demonstrating photography.

Common comparison mistakes and how to avoid them

  • Comparing totals instead of build-ups. The cheapest total usually omits an interface someone else will have to solve later. Price the interfaces, not the panel.
  • Accepting "standard" dimensions for a made-to-measure product. If a supplier quotes a fixed niche size for a wall-system product, ask whether that is a genuine standard module or simply their default.
  • Judging veneer on a small offcut. Grain-matched panels across a wide wall cannot be judged from a 100 mm chip; ask to see a larger panel or a previous installation.
  • Ignoring the reveal depth. A niche framed 20 mm deep reads as intentional joinery; one framed 8 mm deep reads as a cut-out. Specify it, then check every proposal against the same number.
  • Leaving lighting to the electrician. Recessed channels need to be built into the panel build-up. Decide at specification stage and show it on the shop drawing.

Pre-order checklist

  • Specification sheet issued to every bidder, with niche dimensions, shelf layout, finish and lighting.
  • Edge, shelf-junction and substrate samples received and scored against the five tests.
  • Shop drawing signed off, including reveal depth, grain direction and cable routes.
  • Final site dimensions taken and confirmed by the manufacturer, not assumed from architectural drawings.
  • Delivery scope, packaging standard and delivery point written into the order.
  • Installation responsibility, site prerequisites and after-sales terms agreed in writing.

Bringing it together

Comparing samples and proposals for Santerson Open Display Niches comes down to controlling the specification. Write one neutral spec, demand samples that reproduce the real joint rather than a colour chip, score them against fixed tests, and read every proposal for what is missing as much as what is included. Do this once and the price differences stop being confusing: they become evidence, and you can place the order with the details already agreed instead of discovering them during installation.

SANTERSON is a China-based furniture and building materials manufacturer working on villa, hospitality and office projects, with made-to-measure wall systems in the Integrated Storage Walls collection. Send your niche dimensions, drawings and finish references through our contact page and we will return a specification-based proposal with sample options for review.