A swim spa is one of the few site elements where a specification error surfaces after handover, not during construction. If your project has specified or is evaluating the Outdoor Swim Spa WS-P001, the conversation with a supplier should move quickly past brochure language and into three areas: what the catalogue sheet actually commits to, which equipment sits inside the quoted price, and who carries the work from factory floor to the finished terrace. The following checklist is written for buyers, project managers and contractors coordinating villa, resort or hospitality grounds.

1. Start with the dimension set your site can actually accept

The WS-P001 is listed in our swimming pool range with catalogue dimensions of 3500 × 950 mm. That single line tells you two things, and it deliberately does not tell you a third. It gives you the plan footprint and the height to design around — seating level, coping detail, access steps and clearance for maintenance panels all follow from it. What a two-number entry does not settle is water depth, shell geometry or the position of equipment compartments.

Before you compare prices, ask the supplier to confirm in writing: the internal water depth for the configuration you are buying; where the pumps and filtration sit relative to the shell; the minimum plant-room or cabinet clearance needed for service access; and the load path — whether the unit is designed to sit on a fully supported slab, a perimeter beam, or a suspended deck. A supplier who answers these with drawings rather than adjectives is telling you they build to specification, not to a picture.

2. Read the equipment list as an inclusion boundary

The published specifications for this model show a jet total of 81 pcs, two water pumps, one filter pump, one control system and two LED lights, with a total power figure of 8.35 kW. Treat those numbers as the starting point of a negotiation, not the finished scope. Our catalogue notes that availability and compatibility of options vary by model, and the same caution applies to every supplier you speak to.

Specification shownWhat to confirm before ordering
Jet total: 81 pcsJet types and zoning, which seats they serve, and whether the count includes air or hydrotherapy jets that carry separate power draw.
Water pumps: 2 pcs / Filter pump: 1 pcPump duty and flow rate against the shell volume, plus which pumps run for swimming use versus massage use.
Total power: 8.35 kWWhether the figure covers the base unit only, and what it becomes once a heat pump, insulation package or UV sterilization is added.
Features shown: water jets, LED lighting, ozoneWhether ozone is the complete sanitation system for your application, or whether UV sterilization is specified on top of it.
Swim training system: not listedIf your brief calls for lap swimming or resistance training, ask explicitly whether a swim training unit is offered for this model and what it adds to the power load.

The same discipline applies to the options our catalogue lists for this range — control systems, UV sterilization, water pumps, heat pumps, sand filtration, insulation and steps. Ask for each as a priced line item with its own make and rating. A lump-sum quotation hides substitutions; a line-item quotation lets you compare two suppliers on equal terms.

3. Put the electrical and plumbing interface in writing early

Most delays we see on projects of this type are not caused by the shell. They are caused by the handover point between the spa supplier and the site contractor being left undefined. Confirm the supply arrangement — phase, voltage and circuit protection — against the total power figure for your chosen configuration, then agree who provides the isolator, who runs the sub-main, and who terminates at the control system. Do the same for drainage, overflow, fill supply and any heat pump condensate.

A competent supplier will ask you for the site electrical arrangement before finalising the quotation. If nobody on the supply side has asked that question by the time a price is agreed, raise it yourself; an 8.35 kW base load plus optional heat pump is not a detail to discover after the deck has been poured.

4. Test whether the supplier can configure, not just catalogue

Standard units are easy to source anywhere. The value of working with a custom furniture and interior products manufacturer shows up when the site stops being standard — a spa recessed into a terrace edge, a shape that follows a curved landscape line, or a finish that has to match adjacent cabinetry and cladding. Our Customizable Shape Outdoor Spa covers square, round, oval and curved forms with an acrylic shell and structural reinforcement for gardens and terraces, and is the sort of brief a catalogue-only trader cannot take further.

Ask any supplier three questions to test this: can they produce shop drawings from your architect's setting-out; can they prototype or mock up a junction detail such as coping or step interface; and what minimum order quantity applies once you move off the standard specification. Vague answers here are usually a sign that manufacturing is being subcontracted.

5. Check who carries freight, installation and the defects period

A swim spa arrives as a heavy, awkward unit with glass, acrylic and electrical assemblies inside one package. Our logistics service covers sea, air and rail freight forwarding, customs documentation, packaging and container loading, shipment tracking and door-to-door delivery — but you should still confirm the Incoterms on your own quotation, who handles import clearance at destination, and where liability transfers from crate to installed unit.

Then look past delivery. Our service scope runs through consultation, design and planning, production, logistics, installation and after-sales, which for a spa means site setting-out, crane or access arrangements, commissioning of pumps and control system, handover documentation, and a defined route for warranty claims and spare parts such as jets, pumps and LED fittings. Ask which of these sit inside your contract price and which are quoted separately. The answer usually explains more about total project cost than the unit price does.

6. Compare against adjacent models before you commit

Buyers often fix on one model number too early. The WS-P001's 3500 × 950 mm catalogue footprint suits compact terrace and courtyard settings; where the landscape allows a longer run, models in the same range are listed at larger dimensions — for example the Outdoor Swim Spa WS-130AⅢ at 8000 × 3000 × 1400 mm with a swim training system, or the Outdoor Swim Spa WS-S12 at 11740 × 2200 × 1470 mm. Longer shells change the jet layout, the pump duty and the power demand, so compare whole configurations rather than model names.

If the brief is hydrotherapy and entertaining rather than swimming lengths, a dedicated spa such as our Luxury Outdoor Swim Spa with Massage Jets, LED & Water Features may serve the site better at a smaller footprint. Set the intended weekly use pattern down first — exercise, therapy, children, hospitality guests — and let that drive the model choice instead of appearance.

What to send the supplier on day one

To move a WS-P001 enquiry from price check to firm quotation in one round, send: the setting-out drawing with deck levels and access route; the intended use pattern and expected user numbers; your site electrical arrangement; the required finish for cabinet and coping interfaces; and your programme milestones for delivery and commissioning. With those five items a serious supplier can return a configuration, an itemised quotation and an honest lead time.

SANTERSON has operated since 2008 as a China-based furniture and building materials manufacturer and one-stop supplier, covering outdoor structures, interior fixtures and building finishes for villa, hospitality and office projects. Send us your swim spa brief — dimensions, use pattern and site constraints — and we will confirm the configuration, included equipment and electrical requirements before you commit to a price.