A tall cabinet with a glass front looks simple on a drawing. It is one of the easiest items in a joinery schedule to get wrong, because the visible part, the glass, carries decisions about frame, storage, safety, lighting and site clearance all at once. When we quote Santerson Glass Front Tall Cabinets for a residential project, the enquiries that come back fastest to confirm are almost always the ones where the buyer has written down what they actually need rather than what a catalogue picture implies. This guide sets out the fields worth filling in before you request a quotation, and what each one changes on site.
What the product is, and what it is not
Santerson Glass Front Tall Cabinets sits inside our Tall Cabinets collection. The units are made to order for each project: dimensions, finish and internal layout are specified rather than chosen from a fixed size ladder, and the same applies to the glass and the storage configuration behind it. That configurability is the point of the product, and it is also why two cabinets that look identical in a photograph can carry quite different prices.
It helps to be precise about scope. A glass front tall cabinet in this family is a full-height built-in unit with glazed door panels, used where a project wants display or a lighter visual weight in a run of cabinetry. If the requirement is storage for appliances, cleaning equipment or household stock, the closer matches are Santerson Utility Tall Cabinets or Santerson Integrated Appliance Tall Cabinets. If the requirement is open display with no door at all, look at Santerson Open Shelf Tall Cabinets. Specifying the wrong member of the collection is a common and expensive mistake, because a glazed door that was never needed adds cost, and an open bay that was meant to be closed cannot be fixed later without remaking the carcass.
The seven fields a specification needs
Treat the enquiry as a form with seven sections. Missing information in any one of them produces a quotation that is either padded or unusable.
| Field | What to write down | Why it matters |
|---|---|---|
| 1. Opening and clearance | Finished floor level to finished ceiling, plus the wall build-up on each side and whether a cornice, skirting or service run sits in the way. | A full-height unit is dimensioned against the completed room, not the slab. Ceiling services and floor finishes are usually installed after the joinery drawing, so state which levels are final. |
| 2. Door and frame | Hinged or sliding, number of leaves, which hand the door opens, frame profile and frame colour. | Door swing needs clearance in front of the unit. Sliding leaves need a pocket or an overlap. Both decisions change the carcass. |
| 3. Glass | Clear, frosted, smoked or ribbed; thickness and any toughening requirement for the position; whether the panel is full-height or split. | Glass choice controls how much of the contents you see, and where a glazed panel must be safety-rated. Confirm the glass type and its fitting detail per unit. |
| 4. Internal layout | Shelf heights and count, whether shelves are adjustable, drawer or basket sections, hanging rail, and anything you intend to store on each level. | Shelf spacing is where a display cabinet either works or becomes a cupboard full of dead space. Tell us what goes in, not just how many shelves you want. |
| 5. Carcass and finish | Board material and thickness, edge treatment, interior colour versus exterior colour, and the finish family used elsewhere in the room so the unit can be matched. | A tall cabinet rarely stands alone. Send the finish reference of the adjacent run - lacquer, melamine, veneer or acrylic - so the tones match under site lighting. |
| 6. Lighting and services | Whether the unit is lit, how many circuits, where the driver sits, switch location, and whether power or data must pass through the carcass. | Integrated lighting has to be planned with the carcass, not added afterwards. Our Santerson Integrated Cabinet Lighting range is specified alongside the cabinet so driver access and electrical ratings are settled before production. |
| 7. Load and fixing | What each shelf carries, whether the wall behind can take a full-height fixed unit, and any anti-tip or anchoring requirement for the site. | A tall glazed unit loaded with dense items behaves differently from one holding light display pieces. Shelf depth and span follow from the load, and the fixing method follows from the wall. |
Reading your own drawings before you send them
Most specification gaps are visible on the buyer's side of the exchange. Before sending anything, check four things on the room drawing.
- Is the height dimension taken to a finished surface? A ceiling set down 100 mm changes the unit from a standard full-height box into a made-to-measure one, and it changes where the top shelf sits relative to eye level.
- Does the door have somewhere to go? Sketch the swing arc against the circulation route. In narrow bathrooms and laundry recesses a hinged leaf often loses to a sliding or pocket arrangement.
- What is behind the cabinet? Wet areas, pipework and insulation all affect the fixing detail and sometimes the board choice for the back panel.
- Is the glass doing a job? If it hides storage you use daily, a frosted or ribbed panel does the same work with less visual noise. If it is there to show something, plan the lighting and shelf at the same time.
How we quote configurable tall cabinets
Santerson Glass Front Tall Cabinets falls under our custom and OEM route. You send the opening dimensions, the finish reference and the layout intent; we come back with a proposal that states the carcass build, the glass, the internal configuration and what is excluded. Where a project needs several units across several room types, we group them so the finishes, ironmongery and lighting are consistent across the whole joinery package rather than matched item by item.
For buyers coordinating more than cabinetry - bathroom fit-outs, flooring, wall panels, lighting and loose furniture in the same programme - consolidating these with one supplier reduces the number of interfaces to manage. Our Custom & OEM Service covers bespoke design and prototyping, material and finish selection and production coordination; Logistics & Door-to-Door Delivery handles freight, packaging and documentation; and Installation & After-sales Support covers site fitting and snagging. Terms, lead times and the scope available in your country are confirmed project by project, so treat nothing on this page as a standing guarantee.
A short checklist to send with your enquiry
- Room type and the number of units, with a marked-up plan showing each opening.
- Finished-level heights and the wall build-up at the location.
- Door type, leaf count and handing; glass type and finish.
- Shelf layout with intended loads, plus any drawers, baskets or rails.
- Finish reference from the adjacent cabinetry run.
- Lighting intent and where the driver and switch will sit.
- Delivery address, target programme dates and who is fitting on site.
Send that and a quotation for Santerson Glass Front Tall Cabinets can be prepared without a round of clarifying questions. If you are unsure which member of the tall cabinet family suits the space, send the same information and we will tell you where a utility, appliance-integrated or open-shelf unit would serve the room better.
Talk to us about your joinery package
Contact PHILLIP by phone or WhatsApp on +86-13928214007, by email at santerson@qq.com, or through the contact page. Include your drawings and the checklist above for the fastest response.