A pocket door looks simple on a plan: a slab that slides into a wall cavity and disappears. In practice it is one of the few joinery items where the designer's intent, the buyer's schedule and the site builder's setting-out all have to agree before anything goes into production. This article sets out what designers and procurement teams should settle together when specifying Santerson Wood Veneer Pocket Doors on a villa or residential fit-out, and where misalignment usually causes rework.
Start with the opening, not the door
Pocket doors consume wall thickness and wall length that a hinged door does not. Before anyone discusses veneer species, both sides should confirm what the wall can actually absorb. That means the clear opening width and height, the finished wall build-up on both faces, the depth of the cavity the leaf will travel into, and whether that cavity wall is load-bearing or a partition.
- Clear opening dimensions taken from the finished floor and finished wall face, not the structural slab.
- Wall thickness available for the pocket, including the lining on both sides.
- Obstructions inside the cavity - studs, services, ducting, insulation, bracing.
- Sweep length: a single leaf needs its own width of clear travel; bi-parting or double-pocket layouts need more.
Santerson's pocket door range is made to measure for each project, so these dimensions are the specification input rather than a catalogue constraint. The same applies to Classic Pocket Doors where a project calls for a profiled or panelled look instead of a flat veneer face.
Made-to-measure wood veneer pocket door from the Santerson Pocket Doors collection.
Decide who owns the finish continuity decision
Wood veneer is specified for one reason: the door should read as part of the wall, not as an item hung on it. That only works if the veneer on the door matches the veneer on the surrounding surfaces - same species, same cut, same grain direction, and ideally the same cutting run so figure and colour variation stay consistent.
This is where designers and buyers most often diverge. A designer will typically call out a species and grade; a buyer sourcing separately may accept an equivalent-looking panel. For veneer that assumption fails visibly. Where a project already uses Wood Veneer Panels on the walls, specify the door and the panelling together, from the same production batch, so grain matching can be controlled at the cutting stage rather than on site.
Agree in writing, before order: species and cut; whether the leaf is single-face or double-face veneered; edge treatment; lacquer sheen level; and which sample both parties sign off against.
Hardware and operating requirements are a shared call
The leaf is only half the assembly. Hardware choice determines how the door feels, how wide the opening can be, and whether the detail survives daily use.
| Item to align on | Who decides | Why it belongs in the specification, not on site |
|---|---|---|
| Track, hanger and load rating | Designer + manufacturer | Set by leaf size, veneer substrate weight and cycle frequency. |
| Soft-close or plain close | Client / designer | Affects pocket length and the jamb detail at the closing end. |
| Pull, recess pull or no visible ironmongery | Designer | A visible pull on a flush veneer face breaks the wall reading. |
| Threshold and floor finish transition | Buyer + site team | Floor build-up changes the clear drop under the leaf. |
| Acoustic and privacy expectation | Designer | A pocket cavity transmits sound; a veneer pocket door is not a sealed acoustic assembly unless detailed as one. |
| Lock, catch or flush bolt | Client / designer | Bolt edge preparation must be in the shop drawing. |
Sequence the pocket wall with the rest of the build
A pocket door fails as a project item when it is treated as the last line in the door schedule. The cavity has to be built, lined and braced before wall finishes close up, and the frame has to be set true before plasterboard or cladding goes over it.
- Set-out drawings issued early enough that the framing contractor can build the pocket, not adapt to it.
- Service routing resolved before the cavity is closed - re-routing after lining means opening the wall back up.
- Finish levels confirmed so the door height and the floor transition are calculated against the completed surfaces.
- Site access for delivery and installation, particularly on overseas-sourced joinery where the leaf arrives with other cabinetry rather than with local doors.
Santerson handles project coordination from production through door-to-door delivery, installation support and after-sales, so buyers should place the pocket door order in the same batch as the associated joinery and wall panelling. Splitting it out is where matching and timing problems appear.
Where a veneer pocket door is the wrong answer
Part of good alignment is knowing when not to use this product. Designer and buyer should both be comfortable flagging:
- Insufficient wall length for the leaf to travel - a half-pocket or a Flush Wall Aligned Door may serve better.
- Bathroom and wet-zone exposure, where the wall build-up and the veneer edge detail need explicit agreement before specifying a veneered leaf.
- Structural or services-heavy cavity walls that cannot be opened without redesign.
- High acoustic separation requirements, where the cavity itself undermines the target.
For circulation that needs a flush, minimal face but no cavity, hinged alternatives in the same veneer - such as Santerson Wood Veneer Hinged Doors - keep the design language consistent without the pocket wall.
What a complete specification pack should contain
- Signed-off opening dimensions from finished surfaces, with tolerance stated.
- Veneer species, cut, grade and matched sample reference, cross-referenced to the wall panelling schedule.
- Lacquer sheen and edge detail on both faces.
- Hardware schedule: track, hangers, soft close, pull type, catch or bolt.
- Pocket frame and lining build-up, with responsibility assigned to the framing contractor.
- Floor finish build-up and threshold detail.
- Delivery package, storage location on site, and installation sequence.
- A named point of contact for shop-drawing approval before production release.
Project-specific confirmation is required on every item above. Santerson's product pages list made-to-measure sizing with material and finish options, and dimensions and selected specifications must be confirmed per project - nothing in this article should be read as a standard dimension, a fixed build-up or a performance guarantee.
Checklist for the alignment meeting
- Has the wall been verified as able to accept a pocket, with services resolved?
- Is the veneer on the door matched to the wall panelling by sample, not by description?
- Is hardware selected and load-rated for the actual leaf, not a nominal size?
- Who signs off the shop drawings before production starts?
- Does the delivery schedule put the doors in the same consignment as the joinery they sit against?
If those five questions have written answers, the pocket door stops being a site problem and stays what it was designed to be: an opening that disappears into the wall.
Specify your doors with the joinery
Santerson manufactures made-to-measure wood veneer pocket doors, hinged doors and matching wall panelling for residential and villa projects, with production coordination, door-to-door delivery and installation support. Send your opening dimensions and finish schedule to discuss a matched specification.